Translations:Manuals:MB Plus:Receiver setup menu B/3/en

From BEASTX Wiki
Jump to: navigation, search

Teaching of customized channel order

If you need a customized channel order, please first prepare your transmitter as described here. Additionally make sure that each control function of your transmitter activates one and only one channel, for example by using the servo monitor of your transmitter. This can be tricky especially for throttle/collective pitch functions which are usually coupled by a mixer in the transmitter. In this case set the throttle channel quiet, for example by using the throttle hold switch or providing a flat throttle curve, so that the thrust stick actually controls only the channel for the collective pitch. For the later, keep the possibility to control also the throttle channel like by flipping a switch or similar.

In the following menu points you can assign the different functions by simply actuating the appropriate channel function on your transmitter.

 

Menu point Function
B Collective
C Aileron
D Elevator
E Rudder
F Tail gyro
G Throttle
H CH6 Output
I RPM Governor
J AttitudeControl

 

When you move the control stick/adjust the channel with the transmitter a blue flash of the Status-LED indicates that a channel has been detected. It does not matter how far or in what direction you move the stick or in what position the stick/switch was. Note the channel value itself is not important, but the change of this value is. It is therefore important that only the requested function is activated and not by accident several simultaneously. Otherwise MICROBEAST PLUS may not recognize the allocated channel correctly. If you have moved the wrong stick/switch, you can reactivate the correct function again. The MICROBEAST PLUS remembers only the last function that was operated and confirms it with blue flashing of the Status-LED.

Press the button after learning each function to save the assignment and to go to the next function. Once a channel was assigned, it is no longer available and is ignored by MICROBEAST PLUS for the remaining process. Thus, after learning of the collective pitch function (menu point B) you can enable the throttle function (remove throttle hold and switch to a linear or V shape curve) and teach the throttle channel by re-operating the thrust stick at menu point G. Now the collective pitch channel is no longer considered as this channel has already been assigned previously and MICROBEAST PLUS will detect and use the throttle channel as actuator for throttle function!

The first 6 functions must be assigned as they are necessary for the basic flight control and the button remains locked until you operate a new control function. The other options are optional to assign and can be skipped. If special features like AttitudeControl or RPM Governor are not installed on your device, the specific menu points for assignment will not be accessible at all.

  • The assignment for CH6 Output can be skipped by pressing the button without teaching a channel for this function in case it is not used.
  • Likewise, the assignment of the channel for nitro RPM Governor can be skipped in case it is not needed or if you don‘t want to control the RPM Governor by a separate channel, e. g. if your transmitter does not provide enough free channels. By skipping the assignment the RPM Governor function will use a different operating mode that allows to control it via the throttle channel (set at menu point G) if you like. When used in an electric model the RPM Governor generally is controlled via the throttle channel (set at menu point G). In this case the assignment at menu point I can be skipped anyway, as an assignment will have no effect.
  • Finally at menu point J you have to assign the channel that is used to activate/deactivate the AttitudeControl. Again this can be skipped if not needed or if you don‘t want to use a separate channel. AttitudeControl can still be used then. In this case the channel for the tail gyro sensitivity (set at menu point F) is also used to switch AttitudeControl, see the section about using AttitudeControl for further details.

 

If the Status-LED stays red at one of the menu points this means that there is no valid remote control signal available. A channel assignment in this case is impossible! Check if the receiver is properly bound to the transmitter and that a receiver/transmission protocol of the correct type is selected at Receiver menu point A. Switch off the power and restart the receiver type setup procedure from the beginning.


Blank.png

Please note that the RPM Governor as well as the AttitudeControl will not work as long as these functions have not been enabled at the specific menu points (Setup menu point N and Parameter menu point L). Here in receiver menu only the transmitter channel assignment for controlling these functions is defined.


Blank.png


After the last menu point for channel assignment by pressing the button the Menu-LED jumps directly to Receiver menu point N for throttle failsafe setting.



Blank.png