Bureaucrats, Administrators, translate-proofr
15,689
edits
Changes
Jump to navigation
Jump to search
Line 1:
Line 1: − {{TOC_MBPlusV5}}+ + + Line 14:
Line 16: − + − <br /> − <br /> − + − +
Manuals:MBPlusFblV5:Governormenu B (view source)
Revision as of 08:03, 12 January 2018
, 6 years agono edit summary
<translate>
<translate>
<!--T:1-->
{{DISPLAYTITLE:Motor start position|noerror}}
{{DISPLAYTITLE:Motor start position|noerror}}
{{TOC_MBPlusV5|Manuals:MBPlusFblV5:Governormenu_A/en|Manuals:MBPlusFblV5:Governormenu_C/en|GOVMENU}}
__TOC__
__TOC__
<br />
<br />
<!--T:2-->
GOVERNOR MENU point B is used to set the lowest throttle position. This is necessary for different reasons, i.e. the system must now where is the motor starting point when beginning the automatic spool up of the rotor when enabling the governor from standing still.<br />
GOVERNOR MENU point B is used to set the lowest throttle position. This is necessary for different reasons, i.e. the system must now where is the motor starting point when beginning the automatic spool up of the rotor when enabling the governor from standing still.<br />
<br />
<br />
<br />
<br />
=Adjustment on the device=
=Adjustment on the device= <!--T:3-->
When setting the low throttle position make sure the Status-LED lights up in <font color="#0066FF">'''blue'''</font> color (both electrical as well as nitro). This means that a new valid throttle position has been detected. If the Status-LED lights up in <font color="#FF3300">'''red'''</font> then the throttle stick is too close to the throttle stick center position. This is not considered optimal and therefore can not be used as throttle position. In this case check the setting of the transmitter and the programming of the speed controller or readjust throttle servo, carburetor position and throttle linkage rod.<br />
When setting the low throttle position make sure the Status-LED lights up in <font color="#0066FF">'''blue'''</font> color (both electrical as well as nitro). This means that a new valid throttle position has been detected. If the Status-LED lights up in <font color="#FF3300">'''red'''</font> then the throttle stick is too close to the throttle stick center position. This is not considered optimal and therefore can not be used as throttle position. In this case check the setting of the transmitter and the programming of the speed controller or readjust throttle servo, carburetor position and throttle linkage rod.<br />
<br />
<br />
{{QUOTE|When entering menu point '''B''' initially the Status-LED is off. As long as you do not move the throttle stick, the currently stored position will not be changed. So you can skip menu point '''B''' by a brief push of the button without changing the throttle position when performing subsequent adjustments in SETUP MENU or GOVERNOR MENU later. Conversely this means that you need to move the throttle stick at menu point '''B''' at least once to change the current throttle position!}}<br />
{{QUOTE|When entering menu point '''B''' initially the Status-LED is off. As long as you do not move the throttle stick, the currently stored position will not be changed. So you can skip menu point '''B''' by a brief push of the button without changing the throttle position when performing subsequent adjustments in SETUP MENU or GOVERNOR MENU later. Conversely this means that you need to move the throttle stick at menu point '''B''' at least once to change the current throttle position!}}<br />
<br />
<br />
<br />
<br />
=Setup with StudioX=
=Setup with StudioX= <!--T:4-->
<br />
<br />
<br />
<br />
<br />
<br />
=Setup with StudioXm=
=Setup with StudioXm= <!--T:5-->
<br />
<br />
<br />
<br />