Changes

===How can I increase rotation rate for aileron, elevator and rudder?===

===How can I increase rotation rate for aileron, elevator and rudder?===

The rotation speed on all 3 axis is mostly limited by the capability of the sensors. This is appr. 600deg/s. Practically even less as due to calibration you loose some deg.

The rotation speed on all 3 axis is mostly limited by the capability of the sensors. This is appr. 600deg/s. Practically even less as due to calibration you loose some deg.

The roation speed is only determined by the length of the stick signal (and especially has nothing to do with your cyclic pitch adjustment at setup points J or L and also has nothing to do with the cyclic pitch when steering cyclic on the ground!). So increasing/decreasing the stick throw, mostly done by increasing/decreasing servo throw or using Dualrate in the TX for the specified function, will increase/decrease roation rate.

The roation speed is only determined by the length of the stick signal (and especially has nothing to do with your cyclic pitch adjustment at setup points J or L and also has nothing to do with the cyclic pitch when steering cyclic on the ground!). So increasing/decreasing the stick throw, mostly done by increasing/decreasing servo throw or using Dualrate in the TX for the specified function, will increase/decrease roation rate.

The presets in parameter B are nothing else than different preset dualrate/expo curves inside the MB. When using these it is recommended not to change the output signal in the TX as especially when using expo this will bend, compress or stretch the curves leading to very strange flight behavior (it just is not like adding 5% of expo as the curves between TX and Microbeast will multiply and not sum together!) If you like the feeling of course you can do this. For example a slight increase in stick throw for increasing the roll rate will not significantly deform the Microbeast's internal curve and can be done with no problem. But easiest thing would be to switch flight behaviour to "blue=TX" and adjust the curves in your transmitter as you like (therefor I'd suggest to start with 70% D/R and 25% expo on cylic and 85% D/R and 40% expo on tail).

The presets in parameter B are nothing else than different preset dualrate/expo curves inside the MB. When using these it is recommended not to change the output signal in the TX as especially when using expo this will bend, compress or stretch the curves leading to very strange flight behavior (it just is not like adding 5% of expo as the curves between TX and Microbeast will multiply and not sum together!) If you like the feeling of course you can do this. For example a slight increase in stick throw for increasing the roll rate will not significantly deform the Microbeast's internal curve and can be done with no problem. But easiest thing would be to switch flight behaviour to "blue=TX" and adjust the curves in your transmitter as you like (therefor I'd suggest to start with 70% D/R and 25% expo on cylic and 85% D/R and 40% expo on tail).

Also manufacturers use calculate expo curves different, so we can't tell you what our preset curves correspond to which TXs expo values as we use our own expo and there is no data available for comparing. We did outfly these values and programmed them in the source code so we can't tell what these are in Futaba or JR percentages.

Also manufacturers use calculate expo curves different, so we can't tell you what our preset curves correspond to which TXs expo values as we use our own expo and there is no data available for comparing. We did outfly these values and programmed them in the source code so we can't tell what these are in Futaba or JR percentages.

When parameter B is set to blue and the tail gain is switched to heading lock mode you can see by the status LED at which tail stick position the maximum possible rotation rate on rudder will be reached: At that specific tail stick position it will start to flash. At this point the maximum gyro controlled rotation rate is reached.

When parameter B is set to blue and the tail gain is switched to heading lock mode you can see by the status LED at which tail stick position the maximum possible rotation rate on rudder will be reached: At that specific tail stick position it will start to flash. At this point the maximum gyro controlled rotation rate is reached.

By increasing the stick throw any more the LED will go off. At this point the rate control is switched off and the tail will spin freely. Here the only limit is the maximum possible tail pitch throw and normaly the tail will spin ultra fast. This can be used for example for performaning tail slides or turns with very fast spinning tail. For normal flying around this is not recommended as you may accidentaly steer into the uncontrolled area and the tail may spin too fast or very uneven.

By increasing the stick throw any more the LED will go off. At this point the rate control is switched off and the tail will spin freely. Here the only limit is the maximum possible tail pitch throw and normaly the tail will spin ultra fast. This can be used for example for performaning tail slides or turns with very fast spinning tail. For normal flying around this is not recommended as you may accidentaly steer into the uncontrolled area and the tail may spin too fast or very uneven.

==Further observations==

==Further observations==