Bureaucrats, Administrators, translate-proofr
15,683
edits
Changes
Jump to navigation
Jump to search
Line 16:
Line 16: − + − + + + − + + + Line 37:
Line 41: − + + Line 58:
Line 63: − + + + − + − + Line 84:
Line 91: − + Line 153:
Line 160: − + + +
no edit summary
<!--T:17-->
<!--T:17-->
'''S.Port (inv.)'''<br />
'''S.Port'''<br />
When it comes to sending telemetry data back to the radio it get's more complicated. There is an older system called S.PORT that allows to send telemetry data using a second line. This was firstly introduced for RC drones. One problem here is that the signal is electricaly inverted similar as it is done with Futaba SBUS. But as most controllers do not have signal inverters by default, FRSky did add an inverted S.Port signal to some of their receivers. So that protocol can be read as "normal" UART. If you've got one of those receivers you can use it in combination with MICROBEAST PLUS / ULTRA and NANOBEAST. Please note that you need to add an additional '''10k resistor''' between signal line and ground/minus in order to stabilize the signal!<!-- The MICROBEAST ULTRA has an inverter built in, so here you can use receivers with the original S.PORT.--><br />
When it comes to sending telemetry data back to the radio it get's more complicated. There is an older system called S.PORT that allows to send telemetry data using a second line. This was firstly introduced for RC drones. One problem here is that the signal is electricaly inverted similar as it is done with Futaba SBUS. But as most controllers do not have signal inverters by default, FRSky did add an inverted S.Port signal to some of their receivers. So that protocol can be read as "normal" UART. If you've got one of those receivers you can use it in combination with MICROBEAST PLUS. MICROBEAST ULTRA has an inverter built in, so here you can use receivers with the original (uninverted) S.PORT.<br />
<br />
Please note that you need to add an additional '''10k resistor''' between signal line and ground (minus) in order to stabilize the signal!
<br />
<br />
<!--T:24-->
<!--T:24-->
{| style = "text-align:center;"
{| style = "text-align:center;"
| style = "width: 200px;" | [[File:ArcherRSPlus.png|border|x180px]] || style = "padding: 0px 0px 0px 50px; width: 200px;" | [[File:ArcherRSPlus_Res.png|border|x180px]]
| style = "width: 200px;" | [[File:ArcherRSPlus.png|border|x180px]]
<!-- | style = "padding: 0px 0px 0px 50px; width: 200px;" | [[File:ArcherRSPlus_Res.png|border|x180px]] -->
| style = "padding: 0px 0px 0px 50px; width: 200px;" | [[File:Archer RSPlus Res2.png|border|x180px]]
|-
|-
| Archer RS+ using SBUS and S.Port(inv.) signals || style = "padding: 0px 0px 0px 50px;" | Add 10k resistor between S.Port(inv.) and minus
| Archer RS+ using SBUS and S.Port(inv.) signals || style = "padding: 0px 0px 0px 50px;" | Add 10k resistor between S.Port(inv.) and minus
<!--T:25-->
<!--T:25-->
{| style = "text-align:center;"
{| style = "text-align:center;"
| style = "width: 200px;" | [[File:PullDown DI2 Signal.png|border|x180px]] || style = "padding: 0px 0px 0px 50px; width: 200px;" | [[File:Futaba SBUS2.png|border|x180px]]
| style = "width: 200px;" | [[File:PullDown DI2 Signal.png|border|x180px]]
| style = "padding: 0px 0px 0px 50px; width: 200px;" | [[File:Futaba SBUS2.png|border|x180px]]
|-
|-
| Add 4.7k between signal and minus || style = "padding: 0px 0px 0px 50px;" | Use a small PCB to make soldering easier
| Add 4.7k between signal and minus || style = "padding: 0px 0px 0px 50px;" | Use a small PCB to make soldering easier
| SBUS || - || - || - || - ||
| SBUS || - || - || - || - ||
|-
|-
| SBUS || - || S.Port (inv.) || ESC telemetry || - ||
| SBUS || - || S.Port (inv.) || ESC telemetry || - || MB PLUS & NANOBEAST
|-
| SBUS || - || S.Port || ESC telemetry || - || MB ULTRA
|-
|-
| - || ESC telemetry || F.Port || - || - || only MB ULTRA
| - || ESC telemetry || F.Port || - || - || MB ULTRA
|-
|-
| - || ESC telemetry || - || - || F.Port || only MB ULTRA
| - || ESC telemetry || - || - || F.Port || MB ULTRA
|-
|-
|}
|}
<!--T:21-->
<!--T:21-->
When using [SYS] for the F.Port signal, you must connect the BLE2SYS / USB2SYS adapter at the DI2 port in order to use the StudioX app. Here you need the optional adapter from standard servo connector to 5-pin JST. Alternatively you can simply disconnect the F.PORT signal from SYS temporarily, switch off your radio and power cycle your device. It will then enable "normal" SYS operation for programming purpose. Please note that in this case you will not be able to control the system from the radio during setup with StudioX.<br />
When using [SYS] for the F.Port signal, you must connect the BLE2SYS / USB2SYS adapter at the DI2 port in order to use the StudioX app. Here you need the [https://www.freakware.de/en/p/adapter-cable-telemetry-adapterkabel-micobeast-beastx-bxa76406-a174871.htm Telemetry adapter cable BXA76406] from standard servo connector to 5-pin JST. Alternatively you can simply disconnect the F.PORT signal from SYS temporarily, switch off your radio and power cycle your device. It will then enable "normal" SYS operation for programming purpose. Please note that in this case you will not be able to control the system from the radio during setup with StudioX.<br />
<br />
<br />
<br />
<br />
==Setup with StudioX== <!--T:13-->
==Setup with StudioX== <!--T:13-->
You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. Please note that when using S.PORT telemetry connected to [SYS], you must disconnect the receiver from [SYS]temporarily, switch off your radio and power cycle your device. It will then enable "normal" [SYS] operation for programming purpose. For further informations please refer to the StudioX instruction notes.<br />
You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. For further informations please refer to the StudioX instruction notes.<br />
<br />
Please note that when using S.PORT telemetry connected to [SYS], you must disconnect the receiver from [SYS] temporarily, switch off your radio and power cycle your device. It will then enable "normal" [SYS] operation for programming purpose. When using F.Port connected at [SYS] in combination with MICROBEAST ULTRA you can connect your BLE2SYS/USB2SYS at the DI2 port at the side of the device using the [https://www.freakware.de/en/p/adapter-cable-telemetry-adapterkabel-micobeast-beastx-bxa76406-a174871.htm Telemetry adapter cable BXA76406].<br />
<br />
<br />