View source for Manuals:MB Plus:Preliminary steps

<translate>
<!--T:1-->
{{DISPLAYTITLE: Preliminary steps|noerror}}
{{TOC_MBPlus}}
__TOC__

==Mounting the Microbeast PLUS unit== <!--T:2-->
Attach the Microbeast PLUS unit by using one of the provided 3M® gyropads at a preferably low vibrating position on your helicopter such as the gyro platform or receiver platform. You may need to choose another type of mounting pad depending on the vibration pattern of your helicopter. For more information please ask you Microbeast PLUS dealer.<br />
<br />
The MICROBEAST PLUS unit can be attached '''flat or upright''' on the helicopter. However, the '''servo connector pins must always point towards the front or rear''' of the helicopter. The small white sensor pinboard on the side must always be inline with flight direction.<br />
<br />
<gallery widths="350" heights="300" mode="nolines">
Image:450 flat.jpg
Image:450 upright.jpg
</gallery>
<br />
<br />
'''Pay attention that the edges of the Microbeast PLUS unit are all parallel with the corresponding rotational axes of the helicopter!''' Especially make sure that the mounting platform is perpendicular to the main shaft! On the other hand it is not important that the unit is directly placed on the rotation axis (which is nearly impossible).<br/>
<br />
<gallery widths="500" heights="300" mode="nolines">
Image:Mounting_trex500.jpg
</gallery>
<div class="clear"></div> 
<br />
<br />
'''There are eight possible mounting orientations:'''<br />
<br />
<gallery mode="nolines" widths=200px>
File:orient1.jpg|flat, cover on top, servo connectors showing to front
File:orient2.jpg|upright, button on top, servo connectors showing to front
File:orient3.jpg|flat, cover showing to bottom, servo connectors showing to front
File:orient4.jpg|upright, button on bottom, servo connectors showing to front
</gallery>
<br/>
<gallery mode="nolines" widths=200px>
File:orient5.jpg|flat, cover on top, servo connectors showing to rear
File:orient6.jpg|upright, button on top, servo connectors showing to rear
File:orient7.jpg|flat, cover showing to bottom, servo connectors showing to rear
File:orient8.jpg|upright, button on bottom, servo connectors showing to rear
</gallery>
<br/>

==Preparing the transmitter== <!--T:3-->
You can use nearly any transmitter that provides at least 6 channels. By default 5 channels are used for controlling Microbeast PLUS and one channel controls the motor. If using additional features like AttitudeControl or (nitro) RPM Governor more channels may be useful to have.<br />
<br />
Create a new model in your radio‘s model memory. Disable any mixing functions for the swashplate or rudder. Each function should be assigned to just one receiver channel.<br />
<br />
{{QUOTE|'''Never enable your radio‘s eCCPM mixing function!''' All the swashplate mixing will be done by Microbeast PLUS. Always set your radio‘s swash mixer to mCCPM (mechanical mixing) which is often called “H1”,  “1 servo” or “normal“ mixing or disable “swash mixing” if applicable.}}
<br />

<!--T:4-->
Be sure that all trims and sub trims are disabled and that all servo travels are set to 100%. Increasing or decreasing the servo travel/stick throw for aileron, elevator and rudder will later adjust the (maximum) control rates. For the moment to setup Microbeast PLUS let anything stay at default. Also do not adjust the collective pitch curve at the moment. For the setup procedures it has to be set as a straight line reaching from -100% to +100% (or 0 to 100% depending on radio brand).<br />
<br />
Again make sure that there are no mixing functions active (for example rudder revo-mixing). Have a look at the radio’s servo monitor: each stick has to control one channel/servo output (except for thrust stick which typically controls collective pitch and motor). Remember when using Microbeast PLUS you do not directly control the servos of the helicopter. By moving a stick you give a control command to the Microbeast PLUS unit which then performs the necessary servo movements to move the helictoper in the commanded direction. Each control command is bound to one servo output channel of the transmitter.<br />
<br />
Other functions such as throttle curves, ESC switches or auxiliary functions can be adjusted as usual. When using the RPM Governor function the throttle adjustment will be described later. Also the switch assignment for AttitudeControl will discussed at the specific topic.<br />
<br />
{{QUOTE|[[File:Warning.png|18px|sub]] '''Always make sure that the motor in electric models can not start when doing the adjustment work!''' If the drive battery is used as power supply for receiver, servos and Microbeast PLUS, disconnect the motor from the ESC.}}
<br />
</translate>