Help:StudioX:HMSoft - Revision history

Shornstein at 20:33, 21 August 2024

2024-08-21T20:33:05Z

← Older revision		Revision as of 20:33, 21 August 2024
Line 41:		Line 41:

	<!--T:9-->		<!--T:9-->
	At first enter: AT+~~BAUD?~~<br />		At first enter: AT+MODE2<br />
			The interface should reply: OK+Set:2<br />
	<br />		<br />
			Then enter: AT+BAUD?<br />
	The interface should reply: OK+Get:7<br />		The interface should reply: OK+Get:7<br />
	~~In case it show a different number, the baud rate is not set correctly.<br />~~
	<br />		<br />
			In case it shows a different number, the baud rate is not set correctly.<br />
	You can change the setting by entering the command: AT+BAUD7<br />		You can change the setting by entering the command: AT+BAUD7<br />
	~~<br />~~
	The interface will reply: OK+Set:7<br />		The interface will reply: OK+Set:7<br />
	~~<br />~~
	~~<br />~~

	~~<!--T:10-->~~
	~~Next please enter: AT+MODE?<br />~~
	~~<br />~~
	~~The interface should reply: OK+Get:1<br />~~
	~~In case it show a different number, the communication mode is not set correctly.<br />~~
	~~<br />~~
	~~You can change the setting by entering the command: AT+MODE1<br />~~
	~~<br />~~
	~~The interface will reply: OK+Set:1<br />~~
	~~<br />~~
	<br />		<br />

	<!--T:11-->		<!--T:11-->
	~~Finally~~ you can change the name of the device: AT+NAMEUSB2SYS~~<br />~~		If you like you can change the name of the device: AT+NAMEUSB2SYS<br />
	<br />
	The interface should reply: OK+Set:USB2SYS<br />		The interface should reply: OK+Set:USB2SYS<br />
	<br />		<br />

			<!--T:10-->
			Finally enter: AT+MODE1<br />
			The interface should reply: OK+Set:1<br />
	<br />		<br />

	<!--T:12-->		<!--T:12-->
	===Connection to StudioX app===		===Connection to StudioX app===
	Now setup should be finished. Disconnect the device from the app and close the app completely. Power cycle you BLE2SYS and reconnect to the BEASTX ~~systems~~'s SYS-port. The blue LED on BLE2SYS should be flashing steadily.<br />		Now setup should be finished. Disconnect the device from the app and close the app completely. Power cycle you BLE2SYS and reconnect to the BEASTX system's SYS-port. The blue LED on BLE2SYS should be flashing steadily.<br />
	<br />		<br />
	Start StudioX and search for the device ''BLE2SYS'', if needed (click '''Refresh'''). Then click the '''Connect''' button. The blue LED should light up steadily and you BEASTX system should connect now.<br />		Start StudioX and search for the device ''BLE2SYS'', if needed (click '''Refresh'''). Then click the '''Connect''' button. The blue LED should light up steadily and you BEASTX system should connect now.<br />

Shornstein at 07:58, 21 August 2024

2024-08-21T07:58:44Z

← Older revision		Revision as of 07:58, 21 August 2024
Line 1:		Line 1:
	<translate>		<translate>
	<!--T:1-->		<!--T:1-->
			{{DISPLAYTITLE:(Re)Configuration of BLE2SYS interface\|noerror}}
	The BLE2SYS interface is a bluetooth to serial bridge. The newer version 2 uses a HM-18 blueotooth stack from DSD Tech. In rare cases, the devices may not have been reconfigured at the factory for use with the BEASTX system. Usually this is the case when the device name is ''HMSOFT'' instead of ''BLE2SYS'' when searching for the device in StudioX.<br />		The BLE2SYS interface is a bluetooth to serial bridge. The newer version 2 uses a HM-18 blueotooth stack from DSD Tech. In rare cases, the devices may not have been reconfigured at the factory for use with the BEASTX system. Usually this is the case when the device name is ''HMSOFT'' instead of ''BLE2SYS'' when searching for the device in StudioX.<br />
	<br />		<br />

Shornstein: Marked this version for translation

2024-08-21T07:47:52Z

Marked this version for translation

← Older revision		Revision as of 07:47, 21 August 2024
Line 1:		Line 1:
	<translate>		<translate>
			<!--T:1-->
	The BLE2SYS interface is a bluetooth to serial bridge. The newer version 2 uses a HM-18 blueotooth stack from DSD Tech. In rare cases, the devices may not have been reconfigured at the factory for use with the BEASTX system. Usually this is the case when the device name is ''HMSOFT'' instead of ''BLE2SYS'' when searching for the device in StudioX.<br />		The BLE2SYS interface is a bluetooth to serial bridge. The newer version 2 uses a HM-18 blueotooth stack from DSD Tech. In rare cases, the devices may not have been reconfigured at the factory for use with the BEASTX system. Usually this is the case when the device name is ''HMSOFT'' instead of ''BLE2SYS'' when searching for the device in StudioX.<br />
	<br />		<br />

			<!--T:2-->
	To solve this issue you can send the device back to your dealer and ask for replacement. The faster solution maybe to simply reprogram the device by yourself. This is shown in the following section.<br />		To solve this issue you can send the device back to your dealer and ask for replacement. The faster solution maybe to simply reprogram the device by yourself. This is shown in the following section.<br />
	<br />		<br />

			<!--T:3-->
	=== Download configuration software ===		=== Download configuration software ===
	To be able to communicate with the device we need an app from the manufacturer. This is called ''DSD Tech Bluetooth'' and can be found on Apple's AppStore or Google Play store.<br />		To be able to communicate with the device we need an app from the manufacturer. This is called ''DSD Tech Bluetooth'' and can be found on Apple's AppStore or Google Play store.<br />
	<br />		<br />

			<!--T:4-->
	[[File:DSDTech AppStore.png\|none\|x300px]]		[[File:DSDTech AppStore.png\|none\|x300px]]
	<br />		<br />

			<!--T:5-->
	[https://apps.apple.com/us/app/dsd-tech-bluetooth/id1441528159 Click here to open the Apple AppStore]<br />		[https://apps.apple.com/us/app/dsd-tech-bluetooth/id1441528159 Click here to open the Apple AppStore]<br />
	<br />		<br />
Line 19:		Line 24:
	<br />		<br />

			<!--T:6-->
	===Setting BLE2SYS parameters===		===Setting BLE2SYS parameters===
	Now please open the DSD Tech Bluetooth app and establish connection with the ''HMSOFT'' device. When the software is connected to the interface, the blue LED lights up steadily. Tap the device to get to the configuration screen.<br />		Now please open the DSD Tech Bluetooth app and establish connection with the ''HMSOFT'' device. When the software is connected to the interface, the blue LED lights up steadily. Tap the device to get to the configuration screen.<br />
	<br />		<br />

			<!--T:7-->
	Make sure the buttons '''HEX Mode''' are set to '''off'''!<br />		Make sure the buttons '''HEX Mode''' are set to '''off'''!<br />
	<br />		<br />
Line 28:		Line 35:
	<br />		<br />

			<!--T:8-->
	[[File:HMSoft Baudrate.png\|none\|x300px]]		[[File:HMSoft Baudrate.png\|none\|x300px]]
	<br />		<br />

			<!--T:9-->
	At first enter: AT+BAUD?<br />		At first enter: AT+BAUD?<br />
	<br />		<br />
Line 42:		Line 51:
	<br />		<br />

			<!--T:10-->
	Next please enter: AT+MODE?<br />		Next please enter: AT+MODE?<br />
	<br />		<br />
Line 53:		Line 63:
	<br />		<br />

			<!--T:11-->
	Finally you can change the name of the device: AT+NAMEUSB2SYS<br />		Finally you can change the name of the device: AT+NAMEUSB2SYS<br />
	<br />		<br />
Line 59:		Line 70:
	<br />		<br />

			<!--T:12-->
	===Connection to StudioX app===		===Connection to StudioX app===
	Now setup should be finished. Disconnect the device from the app and close the app completely. Power cycle you BLE2SYS and reconnect to the BEASTX systems's SYS-port. The blue LED on BLE2SYS should be flashing steadily.<br />		Now setup should be finished. Disconnect the device from the app and close the app completely. Power cycle you BLE2SYS and reconnect to the BEASTX systems's SYS-port. The blue LED on BLE2SYS should be flashing steadily.<br />
Line 65:		Line 77:
	<br />		<br />

			<!--T:13-->
	<br />		<br />
	<br />		<br />
	<br />		<br />
	</translate>		</translate>

Shornstein: Created page with " The BLE2SYS interface is a bluetooth to serial bridge. The newer version 2 uses a HM-18 blueotooth stack from DSD Tech. In rare cases, the devices may not have been reconfigured at the factory for use with the BEASTX system. Usually this is the case when the device name is ''HMSOFT'' instead of ''BLE2SYS'' when searching for the device in StudioX.

To solve this issue you can send the device back to your dealer and ask for replacement. The faste..."

2024-08-21T07:47:45Z

Created page with "<translate> The BLE2SYS interface is a bluetooth to serial bridge. The newer version 2 uses a HM-18 blueotooth stack from DSD Tech. In rare cases, the devices may not have been reconfigured at the factory for use with the BEASTX system. Usually this is the case when the device name is ''HMSOFT'' instead of ''BLE2SYS'' when searching for the device in StudioX. To solve this issue you can send the device back to your dealer and ask for replacement. The faste..."

New page

<translate>
The BLE2SYS interface is a bluetooth to serial bridge. The newer version 2 uses a HM-18 blueotooth stack from DSD Tech. In rare cases, the devices may not have been reconfigured at the factory for use with the BEASTX system. Usually this is the case when the device name is ''HMSOFT'' instead of ''BLE2SYS'' when searching for the device in StudioX. 
 

To solve this issue you can send the device back to your dealer and ask for replacement. The faster solution maybe to simply reprogram the device by yourself. This is shown in the following section. 
 

=== Download configuration software ===
To be able to communicate with the device we need an app from the manufacturer. This is called ''DSD Tech Bluetooth'' and can be found on Apple's AppStore or Google Play store. 
 

[[File:DSDTech AppStore.png|none|x300px]]
 

[https://apps.apple.com/us/app/dsd-tech-bluetooth/id1441528159 Click here to open the Apple AppStore] 
 
[https://play.google.com/store/apps/details?id=com.reb.dsd_ble&pcampaignid=web_share Click here to open the Google Play store] 
 
 

===Setting BLE2SYS parameters===
Now please open the DSD Tech Bluetooth app and establish connection with the ''HMSOFT'' device. When the software is connected to the interface, the blue LED lights up steadily. Tap the device to get to the configuration screen. 
 

Make sure the buttons '''HEX Mode''' are set to '''off'''! 
 
Then enter the following commands at the lower section. After each command click the send button and check that you get an reply from the device as expected: 
 

[[File:HMSoft Baudrate.png|none|x300px]]
 

At first enter: AT+BAUD? 
 
The interface should reply: OK+Get:7 
In case it show a different number, the baud rate is not set correctly. 
 
You can change the setting by entering the command: AT+BAUD7 
 
The interface will reply: OK+Set:7 
 
 

Next please enter: AT+MODE? 
 
The interface should reply: OK+Get:1 
In case it show a different number, the communication mode is not set correctly. 
 
You can change the setting by entering the command: AT+MODE1 
 
The interface will reply: OK+Set:1 
 
 

Finally you can change the name of the device: AT+NAMEUSB2SYS 
 
The interface should reply: OK+Set:USB2SYS 
 
 

===Connection to StudioX app===
Now setup should be finished. Disconnect the device from the app and close the app completely. Power cycle you BLE2SYS and reconnect to the BEASTX systems's SYS-port. The blue LED on BLE2SYS should be flashing steadily. 
 
Start StudioX and search for the device ''BLE2SYS'', if needed (click '''Refresh'''). Then click the '''Connect''' button. The blue LED should light up steadily and you BEASTX system should connect now. 
 

 
 
 
</translate>