Manuals:AR7210FblV5:Setupmenu J/de - Revision history

Shornstein: Created page with "=Einstellung über StudioXm= Zu Beginn steht die Taumelscheibe waagrecht und die Rotorblätter sollten 0 Grad Pitchanstellwinkel haben. Befestige eine Pitcheinstelllehre am Bl..."

2018-07-19T09:59:35Z

Created page with "=Einstellung über StudioXm= Zu Beginn steht die Taumelscheibe waagrecht und die Rotorblätter sollten 0 Grad Pitchanstellwinkel haben. Befestige eine Pitcheinstelllehre am Bl..."

← Older revision		Revision as of 09:59, 19 July 2018
Line 31:		Line 31:
	<br />		<br />

	=~~Setup with~~ StudioXm=		=Einstellung über StudioXm=
	~~Initially the swashplate will be leveled and rotorblades will have~~ 0 ~~degrees of pitch when the cyclic throw adjustment screen opens~~. ~~Attach your pitch gauge at the rotorblade or blade grip, calibrate it to~~ 0 ~~degrees and then click the~~ '''~~Measure button~~'''. ~~This will move the rotorblade into measuring position. Now check the pitch gauge~~, ~~we want to see exactly~~ +-6.0 ~~degrees. Increase~~/~~decrease the throw value with the~~ '''+''' ~~and~~ '''- ~~buttons~~''' ~~or the~~ '''~~dial~~''' ~~until the pitch is adjusted correctly~~.<br />		Zu Beginn steht die Taumelscheibe waagrecht und die Rotorblätter sollten 0 Grad Pitchanstellwinkel haben. Befestige eine Pitcheinstelllehre am Blattgriff oder Rotorblatt und kalibriere diese auf 0. Wähle dann '''Messen''', so dass die Taumelscheibe in Messposition fährt. Prüfe jetzt, ob die Pitchlehre +-6.0 Grad Pitch anzeigt und vergrößere/reduziere den Wert (falls nötig) mit '''+''' und '''-''' oder über das '''Drehrad'''. Zwischen der Mess- und Neutralposition kann dabei beliebig oft umgeschaltet werden.<br />
	<br />		<br />
	<br />		<br />

Shornstein: Created page with "=Einstellung am Gerät= Zu Beginn ist die Status LED aus, die Taumelscheibe steht waagrecht und die Rotorblätter sollten 0 Grad Pitchanstellwinkel haben. Befestige eine Pitch..."

2018-07-19T09:59:29Z

Created page with "=Einstellung am Gerät= Zu Beginn ist die Status LED aus, die Taumelscheibe steht waagrecht und die Rotorblätter sollten 0 Grad Pitchanstellwinkel haben. Befestige eine Pitch..."

← Older revision		Revision as of 09:59, 19 July 2018
Line 26:		Line 26:
	<br />		<br />

	=~~Adjustment on the device~~=		=Einstellung am Gerät=
	~~Initially the~~ Status LED ~~will be off~~, ~~the swashplate will be leveled and rotorblades will have~~ 0 ~~degrees of pitch~~. ~~Attach your pitch gauge at the rotorblade or blade grip, calibrate it to~~ 0 ~~degrees and then tap the '''aileron''' stick once~~. ~~This will move the rotorblade into '''measuring position'''~~. ~~Now check the pitch gauge. We want to see exactly~~ +-6.0 ~~degrees. By '''rudder''' stick input you can '''increase~~/~~decrease the amount of pitch'''~~ (~~left~~ = ~~decrease~~, ~~right~~ = ~~increase~~). ~~You can switch back and forth between measure and zero position as often as you like~~. ~~When done click the button to proceed to the next menu point~~.<br />		Zu Beginn ist die Status LED aus, die Taumelscheibe steht waagrecht und die Rotorblätter sollten 0 Grad Pitchanstellwinkel haben. Befestige eine Pitcheinstelllehre am Blattgriff oder Rotorblatt und kalibriere diese auf 0. Tippe dann den Roll-Steuerknüppel einmal kurz an, dadurch fährt die Taumelscheibe in Messposition. Prüfe jetzt, ob die Pitchlehre +-6.0 Grad Pitch anzeigt und vergrößere/reduziere den Winkel (falls nötig) durch Antippen oder Halten des Heck-Steuerknüppels (links = reduzieren, rechts = vergrößern). Zwischen der Mess- und Neutralposition kann dabei beliebig oft umgeschaltet werden. Drücke dann kurz auf den Knopf um zum nächsten Einstellpunkt zu wechseln.<br />
	<br />		<br />
	<br />		<br />

Shornstein: Created page with "{{TOC_AR7210V5/de|Manuals:AR7210FblV5:Setupmenu_I/de|Manuals:AR7210FblV5:Setupmenu_K/de|SETUPMENU}} TOC
"

2018-07-19T09:59:09Z

Created page with "{{TOC_AR7210V5/de|Manuals:AR7210FblV5:Setupmenu_I/de|Manuals:AR7210FblV5:Setupmenu_K/de|SETUPMENU}} __TOC__ "

← Older revision		Revision as of 09:59, 19 July 2018
Line 1:		Line 1:
	~~{{DISPLAYTITLE:SETUP MENU J - Cyclic throw\|noerror}}~~		{{TOC_AR7210V5/de\|Manuals:AR7210FblV5:Setupmenu_I/de\|Manuals:AR7210FblV5:Setupmenu_K/de\|SETUPMENU}}
	{{TOC_AR7210V5\|Manuals:AR7210FblV5:Setupmenu_I/en\|Manuals:AR7210FblV5:Setupmenu_K/en\|SETUPMENU}}
	__TOC__		__TOC__
	<br />		<br />

Shornstein: Created page with "SETUPMENÜ J - Weganpassung Taumelscheibe"

2018-07-19T09:58:49Z

Created page with "SETUPMENÜ J - Weganpassung Taumelscheibe"

New page

{{DISPLAYTITLE:SETUP MENU J - Cyclic throw|noerror}}
{{TOC_AR7210V5|Manuals:AR7210FblV5:Setupmenu_I/en|Manuals:AR7210FblV5:Setupmenu_K/en|SETUPMENU}}
__TOC__
 

At SETUP MENU point J we adjust the internal servo throw so that the AR7210BX receiver has a reference on how far it must move the servos when controlling the helicopter. To set the throw you align one rotorblade on the longitudinal axis (in parallel to the tail boom) and measure the cyclic pitch with a digital pitch gauge on this rotorblade. (You can do this from the front or from the rear!) 
{|
|-
| [[Image:Heli_sideview.png|x120px|border]]
| [[Image:Heli_topview.png|x120px|border]]
|} 
 
Initially you should see 0 degrees of pitch now (in case you did the setup at SETUP MENU point H properly!). Then you switch to the adjustment position. The system will give some amount of pitch which you measure again. This time you should see 6.0 degrees (+ or - is not of importance). If not, increase or decrease the swash throw accordingly. 
 
The color of the Status LED gives some indication whether you rotorhead geometry is well suited for flybarless usage or not. Ideally the Status LED on the device should be blue when in 6.0 degress position. If it isn't, this means your servo movements cause very much pitch deflection on the rotorhead. This can be bad for the performance as the system may tend to oversteer and overreact very easily. If you have problem with finding correct gain settings or overcompensation later in flight, the cause may be found here. To solve this you can change geometry by moving the linkage balls on the servo horns closer to the servo center. 
 
{|cellpadding="4" cellspacing="0" border="1"
| style="width:100px; text-align:left;" | '''Status-LED''' || style="text-align:center;" | '''Cyclic throw'''
|-
| style="color:white; background-color:#CC66CC" | purple || not good
|-
|style="color:white; background-color:#FF3300" | red || OK
|-
| style="color:white; background-color:#0066FF" | blue || perfect!
|} 
 
 

=Adjustment on the device=
Initially the Status LED will be off, the swashplate will be leveled and rotorblades will have 0 degrees of pitch. Attach your pitch gauge at the rotorblade or blade grip, calibrate it to 0 degrees and then tap the '''aileron''' stick once. This will move the rotorblade into '''measuring position'''. Now check the pitch gauge. We want to see exactly +-6.0 degrees. By '''rudder''' stick input you can '''increase/decrease the amount of pitch''' (left = decrease, right = increase). You can switch back and forth between measure and zero position as often as you like. When done click the button to proceed to the next menu point. 
 
 

=Setup with StudioXm=
Initially the swashplate will be leveled and rotorblades will have 0 degrees of pitch when the cyclic throw adjustment screen opens. Attach your pitch gauge at the rotorblade or blade grip, calibrate it to 0 degrees and then click the '''Measure button'''. This will move the rotorblade into measuring position. Now check the pitch gauge, we want to see exactly +-6.0 degrees. Increase/decrease the throw value with the '''+''' and '''- buttons''' or the '''dial''' until the pitch is adjusted correctly.

Manuals:AR7210FblV5:Setupmenu J/de - Revision history

Shornstein: Created page with "=Einstellung über StudioXm= Zu Beginn steht die Taumelscheibe waagrecht und die Rotorblätter sollten 0 Grad Pitchanstellwinkel haben. Befestige eine Pitcheinstelllehre am Bl..."

Shornstein: Created page with "=Einstellung am Gerät= Zu Beginn ist die Status LED aus, die Taumelscheibe steht waagrecht und die Rotorblätter sollten 0 Grad Pitchanstellwinkel haben. Befestige eine Pitch..."

Shornstein: Created page with "{{TOC_AR7210V5/de|Manuals:AR7210FblV5:Setupmenu_I/de|Manuals:AR7210FblV5:Setupmenu_K/de|SETUPMENU}} __TOC__ "

Shornstein: Created page with "SETUPMENÜ J - Weganpassung Taumelscheibe"

Shornstein: Created page with "{{TOC_AR7210V5/de|Manuals:AR7210FblV5:Setupmenu_I/de|Manuals:AR7210FblV5:Setupmenu_K/de|SETUPMENU}} TOC
"