Manuals:AR7210FblV5:Setupmenu K/de - Revision history

Shornstein: Created page with "= Zusatzinfo Welche Pitchwerte sind sinnvoll für meinen Heli? = Allgemein gilt "je kleiner der Heli, umso mehr Pitch benötigt er". Aber der notwendige und mögliche Pitchwin..."

2018-07-19T10:14:00Z

Created page with "= Zusatzinfo Welche Pitchwerte sind sinnvoll für meinen Heli? = Allgemein gilt "je kleiner der Heli, umso mehr Pitch benötigt er". Aber der notwendige und mögliche Pitchwin..."

← Older revision		Revision as of 10:14, 19 July 2018
Line 45:		Line 45:
	<br />		<br />

	= ~~Extra info: What pitch is useful for my helicopter~~? =		= Zusatzinfo Welche Pitchwerte sind sinnvoll für meinen Heli? =
	~~In general you can say~~ "~~the smaller the helicopter~~, ~~the more pitch you have to set~~". ~~But it also depends on how much motor power you helicopter has~~, ~~the type of rotorblades you use and finally in what you expect to do with the helicopter~~. ~~So beginner or scale pilots will not need as much pitch as a~~ 3D ~~aerobatics pilot or high speed flyer~~. ~~Anyhow~~, ~~as already mentioned above set the pitch range in the~~ AR7210BX ~~receiver~~ so ~~that it roughly fits to your helicopter mechanics and its capabilities~~.<br />		Allgemein gilt "je kleiner der Heli, umso mehr Pitch benötigt er". Aber der notwendige und mögliche Pitchwinkel hängt von vielen anderen Faktoren ab, wie z.B. dem Modellgewicht, der Motorkraft, den Rotorblättern und letztlich auch davon, was und wie Du fliegst. Anfänger oder Scalepiloten werden nicht so viel Pitch benötigen, wie ein 3D Kunstflugpilot oder Speedflieger. Wie aber oben schon angemerkt, sollte der Pitchbereich im AR7210BX Empfänger grundsätzlich an die mechanischen Gegebenheiten des Modells angepasst werden, nicht so sehr an den Piloten.<br />
	<br />		<br />
	{\|cellpadding="2" cellspacing="0" border="1" width="300px" style="text-align: center; font-size:80%;"		{\|cellpadding="2" cellspacing="0" border="1" width="300px" style="text-align: center; font-size:80%;"
	! width="120px" \| ~~Heli size~~ (~~electric~~) !! ~~Maximum pitch~~		! width="120px" \| Heligröße (elektrisch) !! Maximalpitch
	\|-		\|-
	\| 250 \|\| style="text-align: left;" \| 13.0 - 13.5 ~~degrees~~		\| 250 \|\| style="text-align: left;" \| 13.0 - 13.5 Grad
	\|-		\|-
	\| 450 \|\| style="text-align: left;" \| 13.0 - 13.5 ~~degrees~~		\| 450 \|\| style="text-align: left;" \| 13.0 - 13.5 Grad
	\|-		\|-
	\| 500 \|\| style="text-align: left;" \| 13.0 ~~degrees~~		\| 500 \|\| style="text-align: left;" \| 13.0 Grad
	\|-		\|-
	\| 550 \|\| style="text-align: left;" \| 12.5 ~~degrees~~		\| 550 \|\| style="text-align: left;" \| 12.5 Grad
	\|-		\|-
	\| 600 \|\| style="text-align: left;" \| 12.0 - 12.5 ~~degrees~~		\| 600 \|\| style="text-align: left;" \| 12.0 - 12.5 Grad
	\|-		\|-
	\| 700 \|\| style="text-align: left;" \| 11.5 - 12.0 ~~degrees~~		\| 700 \|\| style="text-align: left;" \| 11.5 - 12.0 Grad
	\|-		\|-
	\| 800 \|\| style="text-align: left;" \| 11.5 ~~degrees~~		\| 800 \|\| style="text-align: left;" \| 11.5 Grad
	\|-		\|-
	\|}		\|}
	<br />		<br />
	{\|cellpadding="2" cellspacing="0" border="1" width="300px" style="text-align: center; font-size:80%;"		{\|cellpadding="2" cellspacing="0" border="1" width="300px" style="text-align: center; font-size:80%;"
	! width="120px" \| ~~Heli size~~ (~~nitro~~) !! ~~Maximum pitch~~		! width="120px" \| Motorgröße (Verbrenner) !! Maximalpitch
	\|-		\|-
	\| .37 - .40 \|\| style="text-align: left;" \| 12.0 ~~degrees~~		\| .37 - .40 \|\| style="text-align: left;" \| 12.0 Grad
	\|-		\|-
	\| .50 - .55 \|\| style="text-align: left;" \| 11.5 - 12.0 ~~degrees~~		\| .50 - .55 \|\| style="text-align: left;" \| 11.5 - 12.0 Grad
	\|-		\|-
	\| .90 - .105 \|\| style="text-align: left;" \| 11.5 - 12.0 ~~degrees~~		\| .90 - .105 \|\| style="text-align: left;" \| 11.5 - 12.0 Grad
	\|-		\|-
	\| ~~Gasser~~ \|\| style="text-align: left;" \| 10.5 - 11.0 ~~degrees~~		\| Benzinmotor \|\| style="text-align: left;" \| 10.5 - 11.0 Grad
	\|}<br />		\|}<br />
	<br />		<br />
	<br />		<br />

Shornstein: Created page with "= Einstellung über StudioXm = x250px

1. Steuere '''Pitch''' auf und ab und prüfe, ob die Steuerrichtung am Rotorkopf korrekt ist (falls noc..."

2018-07-19T10:13:35Z

Created page with "= Einstellung über StudioXm = x250px 1. Steuere '''Pitch''' auf und ab und prüfe, ob die Steuerrichtung am Rotorkopf korrekt ist (falls noc..."

← Older revision		Revision as of 10:13, 19 July 2018
Line 29:		Line 29:
	<br />		<br />

	= ~~Setup with~~ StudioXm =		= Einstellung über StudioXm =
	[[File:~~SetupK~~.PNG\|x250px]]<br />		[[File:SetupKm.PNG\|x250px]]<br />
	<br />		<br />
	1. ~~When you see the adjustment screen for the collective pitch move the~~ '''~~thrust~~''' ~~stick up and down and check whether the~~ '''~~pitch is changing direction correctly~~'''~~. If not already done at SETUP MENU point I~~, ~~'''use the reverse function for the pitch channel in the transmitter to reverse direction of pitch movement in case it is wrong'''~~.<br />		1. Steuere '''Pitch''' auf und ab und prüfe, ob die Steuerrichtung am Rotorkopf korrekt ist (falls noch nicht bei Einstellpunkt I durchgeführt). Drehe den '''Pitchkanal mit der Servoumkehr im Fernsteuersender''' um, falls die Richtung verkehrt herum ist.<br />
	<br />		<br />
	2. ~~Afterwards check the~~ Status LED ~~color and display in the app~~: on <span style="color: #4169E1;">'''~~positive pitch~~'''</span> ~~the Status~~ LED ~~must be~~ <span style="color: #4169E1;">'''~~blue~~'''</span>, on <span style="color: #DC143C;">'''~~negative pitch~~'''</span> ~~it must light in~~ <span style="color: #DC143C;">'''~~red~~'''</span> ~~color~~. '''~~In case the display is inverted~~ (~~red~~ = ~~positive and blue~~ = ~~negative~~), ~~reverse the internal pitch direction of the AR7210BX by changing the direction~~ in ~~the app~~.'''<br />		2. Prüfe dann die Farbe der Status LED: bei <span style="color: #4169E1;">'''positiv Pitch'''</span> muss die LED <span style="color: #4169E1;">'''blau'''</span> leuchten und der Balken in der App nach oben in Richtung positiv wandern, bei <span style="color: #DC143C;">'''negativ Pitch'''</span> muss die LED <span style="color: #DC143C;">'''rot'''</span> leuchten und der Balken in der App nach unten in Richtung negativ wandern. '''Falls die LED-Anzeige falsch herum ist (rot = positiv und blau = negativ) und sich der Balken in die falsche Richtung bewegt, ändere die interne Steuerrichtung über die Schaltflächen in der App.'''<br />
	<br />		<br />
	3. ~~If the stick is not moving far enough, you will see the message~~ "~~Increase~~!"~~. In this case~~ '''~~increase the servo throw~~/~~endpoint of the thrust channel in the transmitter for each direction just as far~~ so ~~that the Status LED changes from flashing to solid and the label changes to~~ "OK" ~~in the software when the stick reaches the end positions~~'''. (~~Note~~: ~~Do not increase the endpoints too much in the transmitter~~. ~~We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position~~.)<br />		3. Wenn der '''Pitch'''-Steuerknüppel ganz am Anschlag steht und die Anzeige für positiv und negativ Pitch in der App auf "Vergrößern!" steht, dann '''vergrößere den
			Steuerausschlag/Servoweg im Fernsteuersender für den Pitchkanal genau so weit, bis die Meldung verschwindet und "OK!" angezeigt wird (oder die Status LED am Gerät von blinkend auf dauerhaft leuchtend wechselt)'''. (Hinweis: Stelle den Steuerweg aber nicht zu groß ein. Wenn die Richtungen schon lange vor der Maximalposition angezeigt werden, reduziere den Ausschlag im Sender entsprechend.)<br />
	<br />		<br />
	4. ~~Finally adjust the maximum collective pitch when the thrust stick is at full deflection for each direction using the~~ '''+''' ~~and~~ '''- ~~buttons~~''' in ~~the app~~.<br />		4. Lass den Pitch-Steuerknüppel in Maximalposition und stelle jetzt den gewünschten und zum Heli passenden Maximalwinkel mit den Knöpfen '''+''' und '''-''' in der App ein. Bring dann den Pitch-Steuerknüppel in die tiefste Position und stelle dann auch entsprechend das negative Pitch ein.<br />
	<br />		<br />
	{{QUOTE\|~~Always set the servo direction in the transmitter first, then check the display on the~~ AR7210BX ~~and change the internal control direction if it does not match the real direction~~. '''~~Do not change the internal direction in order to change the servo direction~~! ~~This is only used for telling the system in which direction is up and down~~.''' ~~Be very conscientious when doing this setup step as wrong direction will cause loss of control during rescue bailout and poor performance in general~~!}}<br />		{{QUOTE\|Stelle immer zuerst die Steuerrichtung über den Sender ein! Prüfe dann die interne Steuerrichtung vom AR7210BX Empfänger und passe diese falls nötig an die tatsächliche Steuerrichtung an. '''Ändere nie die interne Steuerrichtung, um die Servolaufrichtungen zu ändern! Die interne Steuerrichtung dient nur dazu, dem System zu zeigen, was "oben" und "unten" ist.''' Sei bei der Einstellung sehr gewissenhaft und prüfe sie mehrfach, eine falsche Einstellung kann zu schlechter Performance und auch zu Fehlfunktionen führen!}}<br />
	<br />		<br />
	<br />		<br />

Shornstein: Created page with "= Einstellung am Gerät = 1. Steuere '''Pitch''' auf und ab und prüfe, ob die Steuerrichtung am Rotorkopf korrekt ist (falls noch nicht bei Einstellpunkt I durchgeführt). Dr..."

2018-07-19T10:12:11Z

Created page with "= Einstellung am Gerät = 1. Steuere '''Pitch''' auf und ab und prüfe, ob die Steuerrichtung am Rotorkopf korrekt ist (falls noch nicht bei Einstellpunkt I durchgeführt). Dr..."

← Older revision		Revision as of 10:12, 19 July 2018
Line 11:		Line 11:
	<br />		<br />

	= ~~Adjustment on the device~~ =		= Einstellung am Gerät =
	1. ~~Move the~~ '''~~thrust~~''' ~~stick up and down and check whether the~~ '''~~pitch is changing direction correctly~~'''~~. If not already done at SETUP MENU point I~~, ~~'''use the reverse function for the pitch channel in the transmitter to reverse direction of pitch movement in case it is wrong'''~~.<br />		1. Steuere '''Pitch''' auf und ab und prüfe, ob die Steuerrichtung am Rotorkopf korrekt ist (falls noch nicht bei Einstellpunkt I durchgeführt). Drehe den '''Pitchkanal mit der Servoumkehr im Fernsteuersender''' um, falls die Richtung verkehrt herum ist.<br />
	<br />		<br />
	2. ~~Afterwards check the~~ Status LED ~~color~~: on <span style="color: #4169E1;">'''~~positive pitch~~'''</span> ~~it must be~~ <span style="color: #4169E1;">'''~~blue~~'''</span>, on <span style="color: #DC143C;">'''~~negative pitch~~'''</span> ~~it must light in~~ <span style="color: #DC143C;">'''~~red~~'''</span> ~~color~~. '''~~In case the display is inverted~~ (~~red~~ = ~~positive and blue~~ = ~~negative~~), ~~tap the aileron stick once to reverse the internal pitch direction of the AR7210BX receiver~~.'''<br />		2. Prüfe dann die Farbe der Status LED: bei <span style="color: #4169E1;">'''positiv Pitch'''</span> muss die LED <span style="color: #4169E1;">'''blau'''</span> leuchten, bei <span style="color: #DC143C;">'''negativ Pitch'''</span> muss sie <span style="color: #DC143C;">'''rot'''</span> leuchten. '''Falls die LED-Anzeige falsch herum ist (rot = positiv und blau = negativ), dann tippe den Rollsteuerknüppel einmal kurz an, um die interne Steuerrichtung vom MICROBEAST PLUS umzudrehen.'''<br />
	<br />		<br />
	3. ~~When you move~~ '''~~thrust stick to full deflection~~''' ~~the~~ Status LED ~~should light~~ '''~~solid~~''', ~~not just flash~~. ~~If this is not the case~~ '''~~increase the servo throw~~/~~endpoint of the thrust channel in the transmitter for each direction just as far~~ so ~~that the~~ Status LED ~~changes from flashing to solid when the stick reaches the end positions~~'''. (~~Note~~: ~~Do not increase the endpoints too much in the transmitter~~. ~~We need an exact match of full stick position and stick end position. So the Status~~ LED ~~should just change from flashing to solid when reaching the end position~~.)<br />		3. Wenn der '''Pitch'''-Steuerknüppel ganz am Anschlag steht, dann muss die Status LED '''dauerhaft leuchten''', nicht nur blinken. Wenn das nicht der Fall ist '''vergrößere den
			Steuerausschlag/Servoweg im Fernsteuersender für den Pitchkanal genau so weit,
			dass die Status LED gerade von blinkend auf dauerhaft leuchtend wechselt, wenn der
			Knüppel die Maximalposition erreicht.'''. (Hinweis: Stelle den Servoweg aber nicht zu groß
			ein. Wenn die LED schon lange vor der Maximalposition leuchtet, reduziere den Ausschlag
			im Sender entsprechend.)<br />
	<br />		<br />
	4. ~~Finally adjust the maximum collective pitch when the thrust stick is at full deflection.~~ '''~~Increase or decrease the maximum amount of collective pitch~~''' ~~with the~~ '''~~rudder~~''' ~~stick~~ (~~left~~ = ~~decrease~~, ~~right~~ = ~~increase~~). ~~Then move the thrust to full~~ negative ~~and again adjust the pitch using the rudder~~.<br />		4. Lass den Pitch-Steuerknüppel in Maximalposition und stelle jetzt mit dem '''Heck'''-Steuerknüppel den gewünschten und zum Heli passenden '''Maximalwinkel''' ein (links = reduzieren, rechts = vergrößern). Bring dann den Pitch-Steuerknüppel in die tiefste Position und stelle dann auch entsprechend das negative Pitch ein.<br />
	<br />		<br />
	{{QUOTE\|~~Always set the servo direction in the transmitter first, then check the display on the~~ AR7210BX ~~and change the internal control direction if it does not match the real direction~~. '''~~Do not change the internal direction in order to change the servo direction~~! ~~This is only used for telling the system in which direction is up and down~~.''' ~~Be very conscientious when doing this setup step as wrong direction will cause loss of control during rescue bailout and poor performance in general~~!}}<br />		{{QUOTE\|Stelle immer zuerst die Steuerrichtung über den Sender ein! Prüfe dann die interne Steuerrichtung vom AR7210BX Empfänger und passe diese falls nötig an die tatsächliche Steuerrichtung an. '''Ändere nie die interne Steuerrichtung, um die Servolaufrichtungen zu ändern! Die interne Steuerrichtung dient nur dazu, dem System zu zeigen, was "oben" und "unten" ist.''' Sei bei der Einstellung sehr gewissenhaft und prüfe sie mehrfach, eine falsche Einstellung kann zu schlechter Performance und auch zu Fehlfunktionen führen!}}<br />
	<br />		<br />
	<br />		<br />

Shornstein: Created page with "Bei Einstellpunkt '''K''' wird der maximale positive und negative Pitchanstellwinkel festgelegt. Stelle dabei sicher, dass das MICROBEAST PLUS die Steuerrichtungen korrekt anz..."

2018-07-19T10:09:55Z

Created page with "Bei Einstellpunkt '''K''' wird der maximale positive und negative Pitchanstellwinkel festgelegt. Stelle dabei sicher, dass das MICROBEAST PLUS die Steuerrichtungen korrekt anz..."

← Older revision		Revision as of 10:09, 19 July 2018
Line 3:		Line 3:
	<br />		<br />

	~~At SETUP MENU point~~ K ~~you set the maximum~~ negative ~~and positive collective pitch for your helicopter~~. ~~Additionaly you have to make sure that the AR7210BX receiver is detecting the direction of motion correctly~~. ~~This especially is important when using the rescue bailout function but also has effect on the normal flying~~!<br />		Bei Einstellpunkt '''K''' wird der maximale positive und negative Pitchanstellwinkel festgelegt. Stelle dabei sicher, dass das MICROBEAST PLUS die Steuerrichtungen korrekt anzeigt. Das ist vor allem für eine korrekte Funktion der AttitudeControl (Rettungsfunktion) wichtig, hat aber auch auf den Normalflug Auswirkungen!<br />
	<br />		<br />
	{{QUOTE\|'''~~Don‘t modify the pitch curves in your transmitter when doing the collective adjustments~~, ~~let everything at default~~ (i.e. -100 0 +100) ~~so the stick is moving the pitch channel over the full range~~.'''<br />		{{QUOTE\|'''Wenn Du die Pitcheinstellung durchführst, muss die Pitchkurve im Sender auf Werkseinstellung stehen (z.B. -100 0 +100). Der Steuerknüppel muss den Pitchkanal über den ganzen Bereich bewegen!'''<br />
	<br />		<br />
	~~When finished you can adjust your pitch curves as you like and as you are used to~~. ~~But for now we need to set the working range which is necessary to gain optimum performance~~. ~~This also includes that it is more important to define the mechanical possible range of your helicopter than adjusting the pitch to your flying style~~. ~~When using a 3D trainer helicopter frame for example this usually will have a symmetric pitch range~~, i.e. ~~reaching from~~ +12 ~~to -12 degrees~~. ~~Now when you are a beginner or scale pilot you would not need that high amount of pitch~~, ~~especially not~~ in ~~the~~ negative ~~section~~. ~~Anyhow, it is not recommended to set the pitch range of the AR7210BX asymmetrical to~~ -4 to +12 ~~degrees for example~~, ~~as this would not represent the helicopters capability~~. ~~Better is to set the endpoints to~~ -12 ~~and~~ +12 ~~degrees and later use the pitch curve setting in your transmitter to adjust the lower end to your preferred flying style~~. ~~Have a look in your helicopters manual to find out what is the optimum pitch range~~.}}<br />		Wenn Du die Einstellung beendet hast, kannst Du die Pitchkurven falls gewünscht ändern, z.B. für verschiedene Flugzustände. Für optimale Performance ist es aber wichtig, dass der grundsätzliche Arbeitsbereich bestimmt wird. Damit verbunden ist auch zu beachten, dass der maximale Pitchwinkel nicht unbedingt von den Vorlieben des Piloten abhängt, sondern vor allem auch durch die mechanische Auslegung und Leistungsfähigkeit des Helis gegeben ist. Bei einem Trainermodell zum Beispiel ist der Pitchbereich üblicherweise symmetrisch und reicht von -12 bis + 12 Grad. Ein Anfänger oder Scalepilot wird diesen Bereich möglicherweise gar nicht nutzen, vor allem nicht in die negative Richtung. Dennoch sollte der maximale Bereich in diesem Fall nicht auf zum Beispiel -4 bis + 12 Grad gestellt werden, weil das nicht den Möglichkeiten des Modells entspricht. Besser ist es, im AR7210BX Empfänger -12 und +12 Grad einzustellen und dann nachträglich über die Pitchkurve im Sender das Pitch entsprechend zu reduzieren. Im Handbuch des Helikopters findest Du Angaben zum optimalen Pitchbereich und der Pitcheinstellung.}}<br />
	<br />		<br />
	<br />		<br />

Shornstein: Created page with "{{TOC_AR7210V5/de|Manuals:AR7210FblV5:Setupmenu_J/de|Manuals:AR7210FblV5:Setupmenu_L/de|SETUPMENU}} TOC
"

2018-07-19T10:09:29Z

Created page with "{{TOC_AR7210V5/de|Manuals:AR7210FblV5:Setupmenu_J/de|Manuals:AR7210FblV5:Setupmenu_L/de|SETUPMENU}} __TOC__ "

← Older revision		Revision as of 10:09, 19 July 2018
Line 1:		Line 1:
	~~{{DISPLAYTITLE:SETUP MENU K - Collective pitch\|noerror}}~~		{{TOC_AR7210V5/de\|Manuals:AR7210FblV5:Setupmenu_J/de\|Manuals:AR7210FblV5:Setupmenu_L/de\|SETUPMENU}}
	{{TOC_AR7210V5\|Manuals:AR7210FblV5:Setupmenu_J/en\|Manuals:AR7210FblV5:Setupmenu_L/en\|SETUPMENU}}
	__TOC__		__TOC__
	<br />		<br />

Shornstein: Created page with "SETUPMENÜ K - Pitcheinstellung"

2018-07-19T10:09:14Z

Created page with "SETUPMENÜ K - Pitcheinstellung"

New page

{{DISPLAYTITLE:SETUP MENU K - Collective pitch|noerror}}
{{TOC_AR7210V5|Manuals:AR7210FblV5:Setupmenu_J/en|Manuals:AR7210FblV5:Setupmenu_L/en|SETUPMENU}}
__TOC__
 

At SETUP MENU point K you set the maximum negative and positive collective pitch for your helicopter. Additionaly you have to make sure that the AR7210BX receiver is detecting the direction of motion correctly. This especially is important when using the rescue bailout function but also has effect on the normal flying! 
 
{{QUOTE|'''Don‘t modify the pitch curves in your transmitter when doing the collective adjustments, let everything at default (i.e. -100 0 +100) so the stick is moving the pitch channel over the full range.''' 
 
When finished you can adjust your pitch curves as you like and as you are used to. But for now we need to set the working range which is necessary to gain optimum performance. This also includes that it is more important to define the mechanical possible range of your helicopter than adjusting the pitch to your flying style. When using a 3D trainer helicopter frame for example this usually will have a symmetric pitch range, i.e. reaching from +12 to -12 degrees. Now when you are a beginner or scale pilot you would not need that high amount of pitch, especially not in the negative section. Anyhow, it is not recommended to set the pitch range of the AR7210BX asymmetrical to -4 to +12 degrees for example, as this would not represent the helicopters capability. Better is to set the endpoints to -12 and +12 degrees and later use the pitch curve setting in your transmitter to adjust the lower end to your preferred flying style. Have a look in your helicopters manual to find out what is the optimum pitch range.}} 
 
 

= Adjustment on the device =
1. Move the '''thrust''' stick up and down and check whether the '''pitch is changing direction correctly'''. If not already done at SETUP MENU point I, '''use the reverse function for the pitch channel in the transmitter to reverse direction of pitch movement in case it is wrong'''. 
 
2. Afterwards check the Status LED color: on '''positive pitch''' it must be '''blue''', on '''negative pitch''' it must light in '''red''' color. '''In case the display is inverted (red = positive and blue = negative), tap the aileron stick once to reverse the internal pitch direction of the AR7210BX receiver.''' 
 
3. When you move '''thrust stick to full deflection''' the Status LED should light '''solid''', not just flash. If this is not the case '''increase the servo throw/endpoint of the thrust channel in the transmitter for each direction just as far so that the Status LED changes from flashing to solid when the stick reaches the end positions'''. (Note: Do not increase the endpoints too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position.) 
 
4. Finally adjust the maximum collective pitch when the thrust stick is at full deflection. '''Increase or decrease the maximum amount of collective pitch''' with the '''rudder''' stick (left = decrease, right = increase). Then move the thrust to full negative and again adjust the pitch using the rudder. 
 
{{QUOTE|Always set the servo direction in the transmitter first, then check the display on the AR7210BX and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the system in which direction is up and down.''' Be very conscientious when doing this setup step as wrong direction will cause loss of control during rescue bailout and poor performance in general!}} 
 
 

= Setup with StudioXm =
[[File:SetupK.PNG|x250px]] 
 
1. When you see the adjustment screen for the collective pitch move the '''thrust''' stick up and down and check whether the '''pitch is changing direction correctly'''. If not already done at SETUP MENU point I, '''use the reverse function for the pitch channel in the transmitter to reverse direction of pitch movement in case it is wrong'''. 
 
2. Afterwards check the Status LED color and display in the app: on '''positive pitch''' the Status LED must be '''blue''', on '''negative pitch''' it must light in '''red''' color. '''In case the display is inverted (red = positive and blue = negative), reverse the internal pitch direction of the AR7210BX by changing the direction in the app.''' 
 
3. If the stick is not moving far enough, you will see the message "Increase!". In this case '''increase the servo throw/endpoint of the thrust channel in the transmitter for each direction just as far so that the Status LED changes from flashing to solid and the label changes to "OK" in the software when the stick reaches the end positions'''. (Note: Do not increase the endpoints too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position.) 
 
4. Finally adjust the maximum collective pitch when the thrust stick is at full deflection for each direction using the '''+''' and '''- buttons''' in the app. 
 
{{QUOTE|Always set the servo direction in the transmitter first, then check the display on the AR7210BX and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the system in which direction is up and down.''' Be very conscientious when doing this setup step as wrong direction will cause loss of control during rescue bailout and poor performance in general!}} 
 
 

= Extra info: What pitch is useful for my helicopter? =
In general you can say "the smaller the helicopter, the more pitch you have to set". But it also depends on how much motor power you helicopter has, the type of rotorblades you use and finally in what you expect to do with the helicopter. So beginner or scale pilots will not need as much pitch as a 3D aerobatics pilot or high speed flyer. Anyhow, as already mentioned above set the pitch range in the AR7210BX receiver so that it roughly fits to your helicopter mechanics and its capabilities. 
 
{|cellpadding="2" cellspacing="0" border="1" width="300px" style="text-align: center; font-size:80%;"
! width="120px" | Heli size (electric) !! Maximum pitch
|-
| 250 || style="text-align: left;" | 13.0 - 13.5 degrees
|-
| 450 || style="text-align: left;" | 13.0 - 13.5 degrees
|-
| 500 || style="text-align: left;" | 13.0 degrees
|-
| 550 || style="text-align: left;" | 12.5 degrees
|-
| 600 || style="text-align: left;" | 12.0 - 12.5 degrees
|-
| 700 || style="text-align: left;" | 11.5 - 12.0 degrees
|-
| 800 || style="text-align: left;" | 11.5 degrees
|-
|}
 
{|cellpadding="2" cellspacing="0" border="1" width="300px" style="text-align: center; font-size:80%;"
! width="120px" | Heli size (nitro) !! Maximum pitch
|-
| .37 - .40 || style="text-align: left;" | 12.0 degrees
|-
| .50 - .55 || style="text-align: left;" | 11.5 - 12.0 degrees
|-
| .90 - .105 || style="text-align: left;" | 11.5 - 12.0 degrees
|-
| Gasser || style="text-align: left;" | 10.5 - 11.0 degrees
|}