Shornstein at 15:02, 26 March 2025

2025-03-26T15:02:27Z

← Older revision		Revision as of 15:02, 26 March 2025
Line 19:		Line 19:
	'''Example:''' Shape S8 - Main gear tooth count 130 teeth / 15 tooth pinion. Gear ratio apprx. 8.65:1. '''F''' - Status-LED purple flashing, '''G''' - Status-LED red, '''H''' - Status-LED purple.<br />		'''Example:''' Shape S8 - Main gear tooth count 130 teeth / 15 tooth pinion. Gear ratio apprx. 8.65:1. '''F''' - Status-LED purple flashing, '''G''' - Status-LED red, '''H''' - Status-LED purple.<br />
	<br />		<br />
	For SAB Goblin helicopters you can calculate using a 165 tooth maingear. I.e. ~~21 T~~ pinion will result in 165/~~21 =~~ apprx. 7.85:1. '''F''' - Status-LED ~~off~~, '''G''' - Status-LED ~~red~~, '''H''' - Status-LED ~~purple~~.}}<br />		For SAB Goblin helicopters you can calculate using a 165 tooth maingear. I.e. 18T pinion will result in 165/18 apprx. 9.15:1. '''F''' - Status-LED purple, '''G''' - Status-LED flash. purple, '''H''' - Status-LED red.}}<br />
	<br />		<br />

Shornstein at 14:58, 26 March 2025

2025-03-26T14:58:02Z

← Older revision		Revision as of 14:58, 26 March 2025
Line 17:		Line 17:
	{{QUOTE\|The gear ratio should be specified in the instruction manual for your helicopter. Especially with electric models it will vary depending on the motor pinion used. For helicopters with a single-stage gear drive the reduction can be calculated by dividing the number of pinion teeth from the main gear tooth count.<br />		{{QUOTE\|The gear ratio should be specified in the instruction manual for your helicopter. Especially with electric models it will vary depending on the motor pinion used. For helicopters with a single-stage gear drive the reduction can be calculated by dividing the number of pinion teeth from the main gear tooth count.<br />
	<br />		<br />
	'''Example:''' Shape S8 - Main gear tooth count 130 teeth / 15 tooth pinion. Gear ratio apprx. 8.65:1. '''F''' - Status-LED purple flashing, '''G''' - Status-LED red, '''H''' - Status-LED purple.}}<br />		'''Example:''' Shape S8 - Main gear tooth count 130 teeth / 15 tooth pinion. Gear ratio apprx. 8.65:1. '''F''' - Status-LED purple flashing, '''G''' - Status-LED red, '''H''' - Status-LED purple.<br />
			<br />
			For SAB Goblin helicopters you can calculate using a 165 tooth maingear. I.e. 21 T pinion will result in 165/21 = apprx. 7.85:1. '''F''' - Status-LED off, '''G''' - Status-LED red, '''H''' - Status-LED purple.}}<br />
	<br />		<br />

Shornstein: Marked this version for translation

2025-03-26T13:54:05Z

Marked this version for translation

← Older revision		Revision as of 13:54, 26 March 2025
Line 6:		Line 6:
	<br />		<br />

			<!--T:2-->
	The Governor of MICROBEAST PLUS/ULTRA in general calculates with the rotor head speed of the helicopter. So as shown at the transmitter setup step of GOVERNOR MENU you can preset the desired head speed very easily and MICROBEAST PLUS/ULTRA will try to maintain this headspeed as close as possible. Thus the detected rotation speed of the motor can be converted into rotor head speed, you must specify the main gear ratio of the helicopter.<br />		The Governor of MICROBEAST PLUS/ULTRA in general calculates with the rotor head speed of the helicopter. So as shown at the transmitter setup step of GOVERNOR MENU you can preset the desired head speed very easily and MICROBEAST PLUS/ULTRA will try to maintain this headspeed as close as possible. Thus the detected rotation speed of the motor can be converted into rotor head speed, you must specify the main gear ratio of the helicopter.<br />
	<br />		<br />

			<!--T:3-->
	For MICROBEAST PLUS Firmware 5.4.0 with Telemetry support this setting is also used for calculating the rotor speed that is displayed in your telemetry screen. Therefor it is not necessary to enable the GOVERNOR feature, of course you can use the internal governor of your ESC when using telemetry! Simply adjust the displayed rotor speed by changing the gear ratio here.<br />		For MICROBEAST PLUS Firmware 5.4.0 with Telemetry support this setting is also used for calculating the rotor speed that is displayed in your telemetry screen. Therefor it is not necessary to enable the GOVERNOR feature, of course you can use the internal governor of your ESC when using telemetry! Simply adjust the displayed rotor speed by changing the gear ratio here.<br />
	<br />		<br />

			<!--T:4-->
	{{QUOTE\|The gear ratio should be specified in the instruction manual for your helicopter. Especially with electric models it will vary depending on the motor pinion used. For helicopters with a single-stage gear drive the reduction can be calculated by dividing the number of pinion teeth from the main gear tooth count.<br />		{{QUOTE\|The gear ratio should be specified in the instruction manual for your helicopter. Especially with electric models it will vary depending on the motor pinion used. For helicopters with a single-stage gear drive the reduction can be calculated by dividing the number of pinion teeth from the main gear tooth count.<br />
	<br />		<br />
Line 17:		Line 20:
	<br />		<br />

			<!--T:5-->
	=Adjustment on the device=		=Adjustment on the device=
	To set the gear ratio on the device you have to adjust three menu points in a row. Menu point '''F''' sets the number of gear ratio before the decimal point, menu points '''G''' and '''H''' specify the first two decimal places. Compare the following table and set the Status-LED using the rudder stick to the corresponding color and condition at each menu point so the desired gear ratio will result as a combination of all three menu points ('''X.YZ:1'''). The ratio can be adjusted in increments of 0.05. Choose the ratio that is the closest for your helicopter and set the menu points one after the other. To proceed to the each menu point briefly push the button. After menu point '''H''' the initial setup is finished and the button press will lead back to operation mode.<br />		To set the gear ratio on the device you have to adjust three menu points in a row. Menu point '''F''' sets the number of gear ratio before the decimal point, menu points '''G''' and '''H''' specify the first two decimal places. Compare the following table and set the Status-LED using the rudder stick to the corresponding color and condition at each menu point so the desired gear ratio will result as a combination of all three menu points ('''X.YZ:1'''). The ratio can be adjusted in increments of 0.05. Choose the ratio that is the closest for your helicopter and set the menu points one after the other. To proceed to the each menu point briefly push the button. After menu point '''H''' the initial setup is finished and the button press will lead back to operation mode.<br />
	<br />		<br />

			<!--T:6-->
	{\|style="text-align:center; margin:0px 40px 0px 20px; float:left; font-size:80%" cellpadding="4" cellspacing="0" border="1"		{\|style="text-align:center; margin:0px 40px 0px 20px; float:left; font-size:80%" cellpadding="4" cellspacing="0" border="1"
	!style="width:150px; text-align:center;" \| Menu point F<br />Status-LED		!style="width:150px; text-align:center;" \| Menu point F<br />Status-LED
Line 50:		Line 55:
	\|}		\|}

			<!--T:7-->
	{\|style="text-align:center; float:left; font-size:80%" cellpadding="4" cellspacing="0" border="1"		{\|style="text-align:center; float:left; font-size:80%" cellpadding="4" cellspacing="0" border="1"
	!style="width:150px;" \| Menu point G<br />Status-LED		!style="width:150px;" \| Menu point G<br />Status-LED
Line 140:		Line 146:
	<br />		<br />

			<!--T:8-->
	When a custom gear ratio was set using StudioX or StudioXm the Status LED will be '''off''' at menu point F. Pressing the button briefly in this combination the menu points '''G''' and '''H''' will be skipped and you will directly exit the menu. Other than that also here you can change the gear ratio with the rudder stick and use one of the preset ratios, but note that in this case the custom ratio will be erased!<br />		When a custom gear ratio was set using StudioX or StudioXm the Status LED will be '''off''' at menu point F. Pressing the button briefly in this combination the menu points '''G''' and '''H''' will be skipped and you will directly exit the menu. Other than that also here you can change the gear ratio with the rudder stick and use one of the preset ratios, but note that in this case the custom ratio will be erased!<br />
	<br />		<br />
	<br />		<br />

			<!--T:9-->
	=Setup with StudioX=		=Setup with StudioX=
	With StudioX simply enter your gear ratio in the app. Here we also added a calculator for single stage main drive systems. Enter your main gear tooth count and pinion size to easily calculate your main gear ratio. This can be directly stored then.<br />		With StudioX simply enter your gear ratio in the app. Here we also added a calculator for single stage main drive systems. Enter your main gear tooth count and pinion size to easily calculate your main gear ratio. This can be directly stored then.<br />
	<br />		<br />

			<!--T:10-->
	'''Please note:''' The value ''Main gear ratio'' does not show the dot in front of the first decimal. So the value "10.0" is displayed as "100".<br />		'''Please note:''' The value ''Main gear ratio'' does not show the dot in front of the first decimal. So the value "10.0" is displayed as "100".<br />
	<br />		<br />
	<br />		<br />

			<!--T:11-->
	[[File:govmenu_basic_setup_divider.png\|x300px]]<br />		[[File:govmenu_basic_setup_divider.png\|x300px]]<br />
	<br />		<br />

Shornstein at 13:53, 26 March 2025

2025-03-26T13:53:59Z

Show changes

Shornstein: Created page with " {{DISPLAYTITLE:Main gear ratio|noerror}} {{TOC_BXFbl|Manuals:BXFbl:Governormenu_D/en|Manuals:BXFbl:Features/en|GOVMENU|}} TOC
"

2024-08-10T10:04:20Z

Created page with " <translate>  {{DISPLAYTITLE:Main gear ratio|noerror}} {{TOC_BXFbl|Manuals:BXFbl:Governormenu_D/en|Manuals:BXFbl:Features/en|GOVMENU|}} __TOC__ <br /> </translate>"

New page

<translate>

{{DISPLAYTITLE:Main gear ratio|noerror}}
{{TOC_BXFbl|Manuals:BXFbl:Governormenu_D/en|Manuals:BXFbl:Features/en|GOVMENU|}}
__TOC__
<br />

</translate>

Manuals:BXFbl:Governormenu F - Revision history

Shornstein at 15:02, 26 March 2025

Shornstein at 14:58, 26 March 2025

Shornstein: Marked this version for translation

Shornstein at 13:53, 26 March 2025

Shornstein: Created page with " {{DISPLAYTITLE:Main gear ratio|noerror}} {{TOC_BXFbl|Manuals:BXFbl:Governormenu_D/en|Manuals:BXFbl:Features/en|GOVMENU|}} __TOC__ "

Shornstein: Created page with " {{DISPLAYTITLE:Main gear ratio|noerror}} {{TOC_BXFbl|Manuals:BXFbl:Governormenu_D/en|Manuals:BXFbl:Features/en|GOVMENU|}} TOC
"