Manuals:BXFbl:Radio Setup:RemoteSat/en - Revision history

FuzzyBot: Updating to match new version of source page

2024-08-10T08:12:16Z

Updating to match new version of source page

← Older revision		Revision as of 08:12, 10 August 2024
Line 1:		Line 1:
	{{TOC_BXFbl\|Manuals:BXFbl:Radio_Setup:FRSKY/en\|Manuals:BXFbl:Radio_Setup:Standard_PPM/en\|\|}}		{{TOC_BXFbl\|Manuals:BXFbl:Radio_Setup:FRSKY/en\|Manuals:BXFbl:Radio_Setup:Standard_PPM/en\|RADIOSETUP\|}}
	{{DISPLAYTITLE:DSMX / DMSS / iBus remote satellite\|noerror}}		{{DISPLAYTITLE:DSMX / DMSS / iBus remote satellite\|noerror}}
	__TOC__		__TOC__

FuzzyBot: Updating to match new version of source page

2024-07-02T14:29:45Z

Updating to match new version of source page

← Older revision		Revision as of 14:29, 2 July 2024
Line 79:		Line 79:
	=BEASTX setup=		=BEASTX setup=
	In order to use your remote satellite receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering		In order to use your remote satellite receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering
	for your radio system if needed.<br />		for your radio system if needed. By default the BEASTX system has a preset channel order that fits to most SPEKTRUM® and JR® radios. If needed you can change the channel ordering in RECEIVER MENU of the BEASTX system.<br />
	<br />		<br />

	{\| class="wikitable" style="text-align: center; margin-left: 70px; background-color: #F9DDCC; border: solid #F18308 2px;"		{\| class="wikitable" style="text-align: center; margin-left: 70px; background-color: #F9DDCC; border: solid #F18308 2px;"
	\|+ style="caption-side:bottom;\|SPEKTRUM® default channel order		\|+ style="caption-side:bottom;\|SPEKTRUM® / JR® default channel order
	\|-		\|-
	! style="width: 100px; background-color: #f4bf9e" \| Channel		! style="width: 100px; background-color: #f4bf9e" \| Channel

FuzzyBot: Updating to match new version of source page

2024-05-30T18:39:40Z

Updating to match new version of source page

← Older revision		Revision as of 18:39, 30 May 2024
Line 60:		Line 60:
	<br />		<br />

	'''MICROBEAST ULTRA'''<br />		'''MICROBEAST ULTRA (v5.9.x)'''<br />
	* Insert a Spektrum® ''Bind Plug'' at the '''[AUX\|PIT\|RUD]''' port.		* Disconnect(!) the Spektrum® remote satellite and switch on the power supply.
	* Disconnect(!) the Spektrum® remote satellite		* During init sequence (LED light H-N is running) push and hold the button for 4 seconds, then release
	* To bind a DSMX satellite switch on the power supply ~~now~~. ~~The yellow~~ LED ~~'''~~A~~''' on the MICROBEAST ULTRA will start to~~ flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash ~~as well.~~ Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).		* LEDs A and H flash in alternating sequence
	* After successful binding procedure the receiver‘s LED will stay solid~~. Then the device~~ will restart and enter RECEIVER MENU if the ~~current~~ receiver ~~type is not set to DSMX or will start with init sequence. Remove the bind plug~~ and proceed.		* Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash in combination with LED A on MICROBEAST
			* Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
			* After successful binding procedure the receiver‘s LED will stay solid
			* Your MICROBEAST will restart and enter RECEIVER MENU. Press button briefly to scan for the receiver and proceed.
	<br />		<br />
	~~<br />~~

	~~<gallery mode="nolines">~~
	~~File:DSMXbind MB ULTRA 1.jpg\|You need: RX, bind plug and battery~~
	~~File:DSMXbind MB ULTRA 2.jpg\|Connect bind plug at [AUX-PIT-RUD]~~
	~~File:DSMXbind MB ULTRA 3.jpg\|Power up MICROBEAST: LED A flashes~~
	~~File:DSMXbind MB ULTRA 4.jpg\|Connect RX at [DI2] - it will also flash~~
	~~File:DSMXbind MB ULTRA 5.jpg\|Start bind sequence on radio~~
	~~File:DSMXbind MB ULTRA 6.jpg\|Bind successful~~
	~~File:DSMXbind MB ULTRA 7.jpg\|Proceed with setup~~
	~~</gallery>~~
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2024-05-22T09:33:30Z

Updating to match new version of source page

← Older revision		Revision as of 09:33, 22 May 2024
Line 47:		Line 47:
	* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).		* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
	* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.		* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
			<br />
			<br />

			<gallery mode="nolines">
			File:DSMXbind MB Plus 1.jpg\|You need: RX, bind plug and battery
			File:DSMXbind MB Plus 2.jpg\|Connect bind plug at [SYS] and RX at [DI2]
			File:DSMXbind MB Plus 3.jpg\|Power up MICROBEAST: LEDs flash
			File:DSMXbind MB Plus 4.jpg\|Start bind sequence on radio
			File:DSMXbind MB Plus 5.jpg\|Bind successful
			File:DSMXbind MB Plus 6.jpg\|Proceed with setup
			</gallery>
	<br />		<br />

Line 61:		Line 72:
	File:DSMXbind MB ULTRA 2.jpg\|Connect bind plug at [AUX-PIT-RUD]		File:DSMXbind MB ULTRA 2.jpg\|Connect bind plug at [AUX-PIT-RUD]
	File:DSMXbind MB ULTRA 3.jpg\|Power up MICROBEAST: LED A flashes		File:DSMXbind MB ULTRA 3.jpg\|Power up MICROBEAST: LED A flashes
	File:DSMXbind MB ULTRA 4.jpg\|Connect ~~your~~ RX - it will also flash		File:DSMXbind MB ULTRA 4.jpg\|Connect RX at [DI2] - it will also flash
	File:DSMXbind MB ULTRA 5.jpg\|Start bind sequence on radio		File:DSMXbind MB ULTRA 5.jpg\|Start bind sequence on radio
	File:DSMXbind MB ULTRA 6.jpg\|~~Binding~~ successful		File:DSMXbind MB ULTRA 6.jpg\|Bind successful
	File:DSMXbind MB ULTRA 7.jpg\|~~RECEIVER MENU point A~~		File:DSMXbind MB ULTRA 7.jpg\|Proceed with setup
	</gallery>		</gallery>
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2024-05-20T19:32:36Z

Updating to match new version of source page

← Older revision		Revision as of 19:32, 20 May 2024
Line 66:		Line 66:
	File:DSMXbind MB ULTRA 7.jpg\|RECEIVER MENU point A		File:DSMXbind MB ULTRA 7.jpg\|RECEIVER MENU point A
	</gallery>		</gallery>
			<br />

			{{QUOTE\|'''In case binding fails:'''
			* If receiver does not start to flash simple plug it off and reconnect. Timing is very crucial here, it can be that the receiver gets power to early and does not enter bind mode then. Try to plug it in quicker.
			* If binding fails on radio side please try again from beginning (power off and start over). Make sure radio is at least 1 meter / 3 feet away from the RX. If you're too close this can cause unstable RF signal.}}
			<br />
			<br />

	=BEASTX setup=		=BEASTX setup=

FuzzyBot: Updating to match new version of source page

2024-05-20T19:25:07Z

Updating to match new version of source page

← Older revision		Revision as of 19:25, 20 May 2024
Line 45:		Line 45:
	'''MICROBEAST PLUS / NANOBEAST'''<br />		'''MICROBEAST PLUS / NANOBEAST'''<br />
	* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.		* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.
	* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).		* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
	* After successful binding procedure the receiver‘s LED will stay solid. On the ~~MICROBEAST PLUS LED '''H'''~~ will ~~flash alternating with all other LEDs for 2 seconds, then~~ the ~~device~~ will ~~restart~~. Remove the bind plug~~. If needed cycle power~~ and ~~enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above)~~.		* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
	<br />		<br />

Line 52:		Line 52:
	* Insert a Spektrum® ''Bind Plug'' at the '''[AUX\|PIT\|RUD]''' port.		* Insert a Spektrum® ''Bind Plug'' at the '''[AUX\|PIT\|RUD]''' port.
	* Disconnect(!) the Spektrum® remote satellite		* Disconnect(!) the Spektrum® remote satellite
	* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).		* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
	* After successful binding procedure the receiver‘s LED will stay solid. ~~LED '''H'''~~ will ~~flash alternating~~ with ~~all other LEDs for 2 seconds, then MICROBEAST will restart~~. Remove the bind plug~~. If needed cycle power~~ and ~~enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above)~~.		* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
	<br />		<br />
	<br />		<br />

			<gallery mode="nolines">
			File:DSMXbind MB ULTRA 1.jpg\|You need: RX, bind plug and battery
			File:DSMXbind MB ULTRA 2.jpg\|Connect bind plug at [AUX-PIT-RUD]
			File:DSMXbind MB ULTRA 3.jpg\|Power up MICROBEAST: LED A flashes
			File:DSMXbind MB ULTRA 4.jpg\|Connect your RX - it will also flash
			File:DSMXbind MB ULTRA 5.jpg\|Start bind sequence on radio
			File:DSMXbind MB ULTRA 6.jpg\|Binding successful
			File:DSMXbind MB ULTRA 7.jpg\|RECEIVER MENU point A
			</gallery>

	=BEASTX setup=		=BEASTX setup=

FuzzyBot: Updating to match new version of source page

2024-05-14T14:16:48Z

Updating to match new version of source page

New page

{{TOC_BXFbl|Manuals:BXFbl:Radio_Setup:FRSKY/en|Manuals:BXFbl:Radio_Setup:Standard_PPM/en||}}
{{DISPLAYTITLE:DSMX / DMSS / iBus remote satellite|noerror}}
__TOC__

 
Older Spektrum® and JR receivers are using multiple remote satellites that connect to a main receiver unit for maximum range and best radio coverage. With MICROBEAST and NANOBEAST you can connect one single remote satellite directly to the flybarless unit for using in small size helicopters in order to save weight and wires. The system can decode the signal of DSMX, DMSS as well as of ALIGN iBus remote satellites. 
 
 

{{WARNING_QUOTE|It is not recommended to use DSMX, DMSS or iBus remote satellites in helis bigger than 450 size. Bigger helis can cause radio interference due to shielding from carbon parts. Also range is restricted when only using one single remote satellite. For bigger helis we highly recommend using a full size receiver with multiple receiving units. For Spektrum® radios we can recommend using newer SRXL2 remote satellite if size matters. These have much better transmission rates and RF stability than older DSMX satellites.}}
 
 

= Connection scheme =
 
'''MICROBEAST PLUS / MICROBEAST ULTRA''' 
Connect the remote satellite at the side of your MICROBEAST. It must be connected at the first 3 pins from the right, when looking at the pin board from the side. Voltage is the first pin from the front/right, minus is the second pin from the right, signal is connected at the third pin from the right. 
 
{|cellspacing="20" style="text-align:center;"
|[[Image:Mbplus_spektrum_rx2.png | x150px]]

|- style="text-align:center; font-size:75%;"
| JR®/Spektrum® remote satellite connected at side pin board

|}
 

The ESC or throttle servo is connected at port ''AIL|CH5'' or ''AIL|IO2'' on the main pinboard. 
 
 

'''NANOBEAST''' 
With NANOBEAST connect your remote satellite to the port marked ''SAT'' on top of the device. 
 

The ESC is connected at port ''CH1''. 
 
 

=Bind procedure Spektrum® DSMX satellite=
 
{{WARNING_QUOTE|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}}
 

'''MICROBEAST PLUS / NANOBEAST''' 
* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* After successful binding procedure the receiver‘s LED will stay solid. On the MICROBEAST PLUS LED '''H''' will flash alternating with all other LEDs for 2 seconds, then the device will restart. Remove the bind plug. If needed cycle power and enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above).
 

'''MICROBEAST ULTRA''' 
* Insert a Spektrum® ''Bind Plug'' at the '''[AUX|PIT|RUD]''' port.
* Disconnect(!) the Spektrum® remote satellite
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' will flash alternating with all other LEDs for 2 seconds, then MICROBEAST will restart. Remove the bind plug. If needed cycle power and enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above).
 
 

=BEASTX setup=
In order to use your remote satellite receiver you have to scan the input type in the RECEIVER MENU of your BEASTX device and set the correct channel ordering
for your radio system if needed. 
 

{| class="wikitable" style="text-align: center; margin-left: 70px; background-color: #F9DDCC; border: solid #F18308 2px;"
|+ style="caption-side:bottom;|SPEKTRUM® default channel order
|-
! style="width: 100px; background-color: #f4bf9e" | Channel
! style="width: 200px; background-color: #f4bf9e" | Function
|-
| CH1 || Throttle
|-
| CH2 || Roll / Aileron
|-
| CH3 || Pitch / Elevator
|-
| CH4 || Rudder
|-
| CH5 || Gyro gain
|-
| CH6 || Thrust / Collective
|-
| CH7 || AttitudeControl (optional)
|-
| CH8 || Governor (optional)
|-
| CH9 || Aux channel (optional)
|}
''(The optional functions are described in the section '''Optional features'''.)'' 
 
 

==MICROBEAST PLUS / MICROBEAST ULTRA==
Push and hold the button on your MICROBEAST and power up the device. Menu LED A will flash instantly. Now release the button. Push again to start the scan process. When scan was successful, Menu LED B will show up. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu LED N by bringing the throttle in lowest position on your radio and push the button again. Now your MICROBEAST will start with init sequence. You can perform basic setup procedure in SETUP MENU when init sequence was completed. For further information about RECEIVER MENU setup, see next section. 
 
 

==NANOBEAST==
Make sure throttle on the radio is in idle position. Connect the remote receiver to ''SAT'' port and power up NANOBEAST. Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.
 
 
 

==Setup with StudioX==
You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the Control menu in StudioX and click the SCAN button in this menu's screen. 
 

(Picture sys adapter!)