Manuals:MBPlusFblV5:ReceiverType/en - Revision history

FuzzyBot: Importing a new version from external source

2019-07-10T17:05:51Z

Importing a new version from external source

← Older revision		Revision as of 17:05, 10 July 2019
Line 190:		Line 190:
	When StudioX is started and your MICROBEAST PLUS was detected by StudioX, click the Control Setup tab to show the adjustment options of RECEIVER MENU. The options you see here are basically similar to the Menu Points you can change directly at the device. At the top of the screen you can see which type of input signal is selected at the moment. The rows below show what channels are assigned to which control functions. Finally, in the last row you can see the internal value for throttle failsafe position that is set at the moment.<br />		When StudioX is started and your MICROBEAST PLUS was detected by StudioX, click the Control Setup tab to show the adjustment options of RECEIVER MENU. The options you see here are basically similar to the Menu Points you can change directly at the device. At the top of the screen you can see which type of input signal is selected at the moment. The rows below show what channels are assigned to which control functions. Finally, in the last row you can see the internal value for throttle failsafe position that is set at the moment.<br />
	<br />		<br />
	{\|class="~~gallery~~" ~~style~~="~~font~~-~~style: italic~~"		<div class="iosgallery">
	\|-		<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20008.PNG">
	~~\|width~~="~~400pt~~" ~~style~~="~~padding~~:~~0px 0px;~~" ~~align~~="~~left~~"~~\|[[File:ClickControlSetup.png\|x250px]]~~		<div>Choose <b>Control setup</b></div>
	\|}<br />		</div>
			<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20011.PNG">
			<div class="iostext">Here you can see current receiver system, function assignment and failsafe setting</div>
			</div>
			<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2019-07-10T17:05:06Z

Importing a new version from external source

← Older revision		Revision as of 17:05, 10 July 2019
Line 219:		Line 219:
	Refer to the tables above and identify the column that represents your receiver type. Check whether your radio transmits the channels in the given order, respectively each stick function on the radio is using the specified channel number on the left. To know the channel assignment of your transmitter you can check the user manual of the transmitter or look at the servo monitor of the transmitter. In order to load the preset assignment choose '''Load defaults''' from the "New receiver detected!" dialog. Immediately after that the "Failsafe" dailog will show up.<br />		Refer to the tables above and identify the column that represents your receiver type. Check whether your radio transmits the channels in the given order, respectively each stick function on the radio is using the specified channel number on the left. To know the channel assignment of your transmitter you can check the user manual of the transmitter or look at the servo monitor of the transmitter. In order to load the preset assignment choose '''Load defaults''' from the "New receiver detected!" dialog. Immediately after that the "Failsafe" dailog will show up.<br />
	<br />		<br />
	~~{\|class="gallery" style="font-style: italic"~~
	\|-
	~~\|width="400pt" style="padding:0px 0px;" align="left"\|[[File:LoadDefaults.png\|x200px]]~~
	~~\|width="400pt" style="padding:0px 20px;" align="left"\|[[File:FailsafeDialog.png\|x200px]]~~
	~~\|}<br />~~
	<br />		<br />

FuzzyBot: Importing a new version from external source

2019-07-10T17:04:32Z

Importing a new version from external source

← Older revision		Revision as of 17:04, 10 July 2019
Line 272:		Line 272:
	To teach the failsafe position choose "Proceed" when asked to teach the failsafe position and set the throttle channel on your remote control to the desired position. Then press '''Set''' to save the position. If you did not connect a function to CH5 Output and don't need throttle failsafe, press '''Cancel''' to complete setup!<br />		To teach the failsafe position choose "Proceed" when asked to teach the failsafe position and set the throttle channel on your remote control to the desired position. Then press '''Set''' to save the position. If you did not connect a function to CH5 Output and don't need throttle failsafe, press '''Cancel''' to complete setup!<br />
	<br />		<br />
	{\|class="~~gallery~~" ~~style~~="~~font~~-~~style: italic~~"		<div class="iosgallery">
	\|-		<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20025.PNG">
	~~\|width~~="~~400pt~~" ~~style~~="~~padding:0px 0px;~~" ~~align~~="~~left"\|[[File~~:~~FailsafeDialog~~.~~png\|x200px]]~~		<div class="iostext">After function assignment click <b>Proceed</b> to start teaching the throttle failsafe position</div>
	~~\|width~~="~~400pt~~" ~~style~~="~~padding:0px 20px;~~" ~~align~~="~~left~~"~~\|[[File~~:~~Setfailsafe~~.~~png\|x250px]]~~		</div>
	\|}<br />		<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20027.PNG">
			<div class="iostext">Move throttle to lowest position at which the motor is turned off</div>
			</div>
			<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20028.PNG">
			<div class="iostext">Click <b>Set</b> to store the setting</div>
			</div>
			<br />
	<br />		<br />
	{{WARNING_QUOTE\|'''During failsafe setting the CH5 Output is enabled and can be controlled by the transmitter channel that is assigned to throttle function.''' This allows to check your throttle position in reality. When using electric models make sure the motor is disconnected from the ESC or the pinion is removed from the motor, so that it will not drive the model by accident.		{{WARNING_QUOTE\|'''During failsafe setting the CH5 Output is enabled and can be controlled by the transmitter channel that is assigned to throttle function.''' This allows to check your throttle position in reality. When using electric models make sure the motor is disconnected from the ESC or the pinion is removed from the motor, so that it will not drive the model by accident.

FuzzyBot: Importing a new version from external source

2019-07-10T17:04:14Z

Importing a new version from external source

← Older revision		Revision as of 17:04, 10 July 2019
Line 199:		Line 199:
	In order to detect the connected receiver type make sure the receiver is bound to the transmitter and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBPlusFblV5:Radio_System/en\|Radio System]]. Press the "Scan" button to start automatic receiver detection routine. The Status-LED on the device and the display will indicate which type the system is scanning for at the moment. When a valid input signal was detected the receiver type will be set automatically and a dialog will appear in case a single-line receiver is used. This asks how to proceed with function assignments. When a Standard receiver is used the system will restart directly and you can leave the setup screen as there . When detection fails once again make sure your receiver is connected properly to MICROBEAST PLUS, bound to the transmitter and sending out control signals and try again.<br />		In order to detect the connected receiver type make sure the receiver is bound to the transmitter and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBPlusFblV5:Radio_System/en\|Radio System]]. Press the "Scan" button to start automatic receiver detection routine. The Status-LED on the device and the display will indicate which type the system is scanning for at the moment. When a valid input signal was detected the receiver type will be set automatically and a dialog will appear in case a single-line receiver is used. This asks how to proceed with function assignments. When a Standard receiver is used the system will restart directly and you can leave the setup screen as there . When detection fails once again make sure your receiver is connected properly to MICROBEAST PLUS, bound to the transmitter and sending out control signals and try again.<br />
	<br />		<br />
	{\|class="~~gallery" style="font-style: italic~~"		<div class="iosgallery">
	\|-		<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20011.PNG">
	~~\|width~~="~~400pt~~" ~~style~~="~~padding~~:~~0px 0px;~~" ~~align~~="~~left~~"~~\|[[File:~~Click ~~Scan~~.~~png\|x250px]]~~		<div class="iostext">Click scan button...</div>
	~~\|width~~="~~400pt~~" ~~style~~="~~padding~~:~~0px 20px;~~" ~~align~~="~~left~~"~~\| [[File:Scan~~ wait~~.png\|x250px]]~~		</div>
	~~\|width~~="~~400pt~~" ~~style~~="~~padding~~:~~0px 20px;~~" ~~align~~="~~left~~"~~\| [[File:NewRxDetected.png\|x200px]]~~		<div class="iosgallery">
	\|}<br />		<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20014.PNG">
			<div class="iostext">...and wait until scan is finished</div>
			</div>
			<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20016.PNG">
			<div class="iostext">If scan was successful the dialog will show up</div>
			</div>
			<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2019-07-10T17:03:19Z

Importing a new version from external source

← Older revision		Revision as of 17:03, 10 July 2019
Line 222:		Line 222:
	<p>In case the channel to function ordering differs from the given tables above on your radio system, you have to manually assign the channel order step by step. This is done by simply actuating the appropriate channel function on your transmitter at each of the menu points B to I (PROEDITION: J). Each menu point represents one control function to assign. When you're ready click '''Teach''' in the "New receiver detected!" dialog and start with function allocation at Menu Point B. When you move the control stick/change the channel output on the transmitter, a blue flash of the Status-LED indicates that the channel has been detected. The setup will jump to the next menu point automatically. It does not matter how far or in what direction you move the stick or in what position the stick/switch was. The channel's value itself is not important, but the change of this value is. <b>It is therefore important that only the requested function is activated and not by accident several simultaneously!</b> Otherwise MICROBEAST PLUS may not recognize the allocated channel correctly. Once a channel was assigned, it is no longer available and is ignored by MICROBEAST PLUS for the remaining process. Thus, after learning of the collective pitch function (at Menu Point B) you can enable the throttle function (remove throttle hold or switch to a linear or V shape curve) and teach the throttle channel by re-operating the thrust stick at Menu Point G. Now the collective pitch channel is no longer considered as this channel has already been assigned previously and MICROBEAST PLUS will detect and use the throttle channel as actuator for throttle function!</p>		<p>In case the channel to function ordering differs from the given tables above on your radio system, you have to manually assign the channel order step by step. This is done by simply actuating the appropriate channel function on your transmitter at each of the menu points B to I (PROEDITION: J). Each menu point represents one control function to assign. When you're ready click '''Teach''' in the "New receiver detected!" dialog and start with function allocation at Menu Point B. When you move the control stick/change the channel output on the transmitter, a blue flash of the Status-LED indicates that the channel has been detected. The setup will jump to the next menu point automatically. It does not matter how far or in what direction you move the stick or in what position the stick/switch was. The channel's value itself is not important, but the change of this value is. <b>It is therefore important that only the requested function is activated and not by accident several simultaneously!</b> Otherwise MICROBEAST PLUS may not recognize the allocated channel correctly. Once a channel was assigned, it is no longer available and is ignored by MICROBEAST PLUS for the remaining process. Thus, after learning of the collective pitch function (at Menu Point B) you can enable the throttle function (remove throttle hold or switch to a linear or V shape curve) and teach the throttle channel by re-operating the thrust stick at Menu Point G. Now the collective pitch channel is no longer considered as this channel has already been assigned previously and MICROBEAST PLUS will detect and use the throttle channel as actuator for throttle function!</p>
	<br />		<br />
	{\|class="~~gallery~~" ~~style~~="~~font~~-~~style: italic~~"		<div class="iosgallery">
	\|-		<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20016.PNG">
	~~\|width~~="~~400pt~~" ~~style~~="~~padding:0px 0px;~~" ~~align~~="~~left~~"~~\|[[File~~:~~TeachChannels~~.~~png\|x250px]]~~		<div>Choose <b>Teach</b></div>
	~~\|width~~="~~400pt~~" ~~style~~="~~padding:0px 20px;~~" ~~align~~="~~left~~"~~\| [[File~~:~~MovePitch~~.~~png\|x250px]]~~		</div>
	~~\|width~~="~~400pt~~" ~~style~~="~~padding:0px 20px;~~" ~~align~~="~~left~~"~~\| [[File~~:~~MoveRoll~~.~~png\|x250px]]~~		<div class="iosgallery">
	\|}<br />		<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20017.PNG">
			<div class="iostext">At first move the stick for collective. Make sure only one channel is moved on the radio otherwise MICROBEAST PLUS is not able to detect the movement!</div>
			</div>
			<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20018.PNG">
			<div class="iostext">Proceed with the other function in similar manner</div>
			</div>
			<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20022.PNG">
			<div class="iostext">The optional functions can be skipped if not needed. See text below!</div>
			</div>
			<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20023.PNG">
			<div class="iostext">When skipping the channel number will be shown as <b>-</b></div>
			</div>
			<br />
	<br />		<br />
	<p>The first 6 functions must be assigned as they are necessary for the basic flight control. The other functions are optional to assign and can be skipped. If special features like AttitudeControl or Headspeed Governor are not installed on your device, the specific menu points for assignment will not be shown at all.		<p>The first 6 functions must be assigned as they are necessary for the basic flight control. The other functions are optional to assign and can be skipped. If special features like AttitudeControl or Headspeed Governor are not installed on your device, the specific menu points for assignment will not be shown at all.
Line 233:		Line 248:
	* Likewise, the assignment of the channel for internal governor can be skipped in case it is not needed or if you don‘t want to control the governor with a separate channel, e. g. if your transmitter does not provide enough free channels. By skipping the assignment the internal governor function will use a different operating mode that allows to control it by the throttle channel if you like. When used in an electric model the internal governor is controlled by the throttle channel in general. In this case the assignment can be skipped anyway, as it will have no effect.		* Likewise, the assignment of the channel for internal governor can be skipped in case it is not needed or if you don‘t want to control the governor with a separate channel, e. g. if your transmitter does not provide enough free channels. By skipping the assignment the internal governor function will use a different operating mode that allows to control it by the throttle channel if you like. When used in an electric model the internal governor is controlled by the throttle channel in general. In this case the assignment can be skipped anyway, as it will have no effect.
	* Finally, you can assign the channel that is used to engage the AttitudeControl/rescue stabilization (only available you've installed the PROEDITION Upgrade on your device). Again this can be skipped if not needed or if you don‘t want to use a separate channel or in case you have no more free channels left). AttitudeControl can still be used then. In this case the channel for the tail gyro gain is used to engage AttitudeControl or can be enabled separately using the Bank Switch feature. Please see the section about using AttitudeControl for further details.</p>		* Finally, you can assign the channel that is used to engage the AttitudeControl/rescue stabilization (only available you've installed the PROEDITION Upgrade on your device). Again this can be skipped if not needed or if you don‘t want to use a separate channel or in case you have no more free channels left). AttitudeControl can still be used then. In this case the channel for the tail gyro gain is used to engage AttitudeControl or can be enabled separately using the Bank Switch feature. Please see the section about using AttitudeControl for further details.</p>
	~~<br />~~
	~~{\|class="gallery" style="font-style: italic"~~
	\|-
	~~\|width="400pt" style="padding:0px 0px;" align="left"\|[[File:MoveAuxorSkip.png\|x250px]]~~
	~~\|width="400pt" style="padding:0px 20px;" align="left"\|[[File:FunctionsSkipped.png\|x250px]]~~
	~~\|}<br />~~
	<br />		<br />
	{{QUOTE\|If the Status-LED lights in '''red color''' this means either there is no valid remote control signal available or that you did try to assign two or more channels to a function. So check if the receiver is connected and powered properly and that you're only moving one channel at a time when trying to do the manual function assignment.}}<br />		{{QUOTE\|If the Status-LED lights in '''red color''' this means either there is no valid remote control signal available or that you did try to assign two or more channels to a function. So check if the receiver is connected and powered properly and that you're only moving one channel at a time when trying to do the manual function assignment.}}<br />

FuzzyBot: Importing a new version from external source

2019-07-09T15:20:02Z

Importing a new version from external source

← Older revision		Revision as of 15:20, 9 July 2019
Line 4:		Line 4:
	<br />		<br />

	<p>Due to the possibility of connecting very different types of receivers with different types of signal output, you must setup the receiver type in the RECEIVER MENU. Additionally when using a single-line receiver it is mandatory to define the function assignment for the receiver output channels ~~as the~~ single-line receiver ~~packs~~ the control information ~~together and~~ it is not clear, which channel controls which (stick) function. Finally when using a single-line receiver you have to set a failsafe position for the throttle channel. This defines at which position the motor is disabled and where to move the throttle in case the receiver is not sending any throttle signal, i.e. during power up or in case of loss of radio link.</p>		<p>Due to the possibility of connecting very different types of receivers with different types of signal output, you must setup the receiver type in the RECEIVER MENU. Additionally when using a single-line receiver it is mandatory to define the function assignment for the receiver output channels. A single-line receiver bundles the control information to data packages or serialized electical signals. So by default it is not clear, which channel controls which (stick) function. Finally when using a single-line receiver you have to set a failsafe position for the throttle channel. This defines at which position the motor is disabled and where to move the throttle in case the receiver is not sending any throttle signal, i.e. during power up or in case of loss of radio link.</p>
	<br />		<br />
	{{QUOTE\|By default the "Standard Receiver" is selected as receiver type. So if you're using this type of receiver and your MICROBEAST PLUS is brand new, you can skip this section as it is already setup correctly!}}<br />		{{QUOTE\|By default the "Standard Receiver" is selected as receiver type. So if you're using this type of receiver and your MICROBEAST PLUS is brand new, you can skip this section as it is already setup correctly!}}<br />
Line 243:		Line 243:
	<br />		<br />

	==~~Point N -~~ Throttle failsafe==		==Throttle failsafe==
	After you've set the control functions you will ~~reach Menu Point N~~ to program the failsafe position for the throttle channel. In case the single-line signal is interrupted during operation the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:		After you've set the control functions you will be asked to program the failsafe position for the throttle channel. In case the single-line signal is interrupted during operation, the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:
	* if using a single-line receiver that turns of the single-line signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® receiver in „SUMDOF“ mode)		* if using a single-line receiver that turns of the single-line signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® receiver in „SUMDOF“ mode)
	* if the connection between MICROBEAST PLUS and receiver gets disconnected		* if the connection between MICROBEAST PLUS and receiver gets disconnected

FuzzyBot: Importing a new version from external source

2019-07-09T15:20:00Z

Importing a new version from external source

← Older revision		Revision as of 15:20, 9 July 2019
Line 207:		Line 207:
	<br />		<br />

	==~~Points B to I (PROEDITION: J)~~==		==Function assignment==
	When using a single-line receiver it is mandatory to define the function assignment for the receiver output channels as the single-line receiver packs the control information together and it is not clear, which channel controls which (stick) function. For each specific type of receiver/radio brand there is an appropriate channel allocation preset in MICROBEAST PLUS. If this does not fit your radio system or if you like to use a different assignment or different options you can manually assign each function step by step at the Menu Points B to I (J). Here each point represents one function to assign.<br />
	~~<br />~~

	===Default function assignment===		===Default function assignment===

FuzzyBot: Importing a new version from external source

2019-07-09T15:19:57Z

Importing a new version from external source

← Older revision		Revision as of 15:19, 9 July 2019
Line 11:		Line 11:

	=Preset function assignments for Single-line receivers=		=Preset function assignments for Single-line receivers=
	When using a single-line receiver it is mandatory to define the function assignment for the receiver output channels as the single-line receiver packs the control information together and it is not clear, which channel controls which (stick) function. For each specific type of receiver/radio brand there is an appropriate channel allocation preset in MICROBEAST PLUS. This preset can be loaded during receiver setup later onwards.<br />
	~~<br />~~

	'''Spektrum® DMS2/DSMX or JR® RJ01 DMSS remote satelite'''		'''Spektrum® DMS2/DSMX or JR® RJ01 DMSS remote satelite'''

FuzzyBot: Importing a new version from external source

2019-07-09T15:19:54Z

Importing a new version from external source

← Older revision		Revision as of 15:19, 9 July 2019
Line 224:		Line 224:

	===Manual function assignment===		===Manual function assignment===
	<p>In case the channel to function ordering differs from the given tables above on your radio system, you have to manually assign the channel order step by step. This is done by simply actuating the appropriate channel function on your transmitter at each of the menu points B to I (PROEDITION: J). Each menu point represents one control function to assign. When you're ready click '''Teach''' in the "New receiver detected!" dialog and start with function allocation at Menu Point B. When you move the control stick/~~adjust~~ the channel on the transmitter, a blue flash of the Status-LED indicates that the channel has been detected. The setup will jump to the next menu point automatically. It does not matter how far or in what direction you move the stick or in what position the stick/switch was. The channel's value itself is not important, but the change of this value is. It is therefore important that only the requested function is activated and not by accident several simultaneously. Otherwise MICROBEAST PLUS may not recognize the allocated channel correctly. Once a channel was assigned, it is no longer available and is ignored by MICROBEAST PLUS for the remaining process. Thus, after learning of the collective pitch function (at Menu Point B) you can enable the throttle function (remove throttle hold or switch to a linear or V shape curve) and teach the throttle channel by re-operating the thrust stick at Menu Point G. Now the collective pitch channel is no longer considered as this channel has already been assigned previously and MICROBEAST PLUS will detect and use the throttle channel as actuator for throttle function!</p>		<p>In case the channel to function ordering differs from the given tables above on your radio system, you have to manually assign the channel order step by step. This is done by simply actuating the appropriate channel function on your transmitter at each of the menu points B to I (PROEDITION: J). Each menu point represents one control function to assign. When you're ready click '''Teach''' in the "New receiver detected!" dialog and start with function allocation at Menu Point B. When you move the control stick/change the channel output on the transmitter, a blue flash of the Status-LED indicates that the channel has been detected. The setup will jump to the next menu point automatically. It does not matter how far or in what direction you move the stick or in what position the stick/switch was. The channel's value itself is not important, but the change of this value is. <b>It is therefore important that only the requested function is activated and not by accident several simultaneously!</b> Otherwise MICROBEAST PLUS may not recognize the allocated channel correctly. Once a channel was assigned, it is no longer available and is ignored by MICROBEAST PLUS for the remaining process. Thus, after learning of the collective pitch function (at Menu Point B) you can enable the throttle function (remove throttle hold or switch to a linear or V shape curve) and teach the throttle channel by re-operating the thrust stick at Menu Point G. Now the collective pitch channel is no longer considered as this channel has already been assigned previously and MICROBEAST PLUS will detect and use the throttle channel as actuator for throttle function!</p>
	<br />		<br />
	{\|class="gallery" style="font-style: italic"		{\|class="gallery" style="font-style: italic"
Line 233:		Line 233:
	\|}<br />		\|}<br />
	<br />		<br />
	<p>The first 6 functions must be assigned as they are necessary for the basic flight control ~~and the button remains locked until you operate a new control function~~. The other functions are optional to assign and can be skipped. If special features like AttitudeControl or ~~RPM~~ Governor are not installed on your device, the specific menu points for assignment will not be ~~accessible~~ at all.		<p>The first 6 functions must be assigned as they are necessary for the basic flight control. The other functions are optional to assign and can be skipped. If special features like AttitudeControl or Headspeed Governor are not installed on your device, the specific menu points for assignment will not be shown at all.
	* The assignment for Aux [CH6] Output ~~at Menu Point H~~ can be skipped by pressing the "Skip" button without teaching a channel for this function in case it is not used.		* The assignment for Aux [CH6] Output can be skipped by pressing the "Skip" button without teaching a channel for this function in case it is not used.
	* Likewise, the assignment of the channel for internal ~~nitro Governor~~ can be skipped in case it is not needed or if you don‘t want to control the ~~Governor~~ with a separate channel, e. g. if your transmitter does not provide enough free channels. By skipping the assignment the internal ~~Governor~~ function will use a different operating mode that allows to control it ~~via~~ the throttle channel ~~(set at Menu Point G)~~ if you like. When used in an electric model the internal ~~Governor generally~~ is controlled ~~with~~ the throttle channel ~~(set at Menu Point G)~~. In this case the assignment ~~at Menu Point I~~ can be skipped anyway, as ~~an assignment~~ will have no effect.		* Likewise, the assignment of the channel for internal governor can be skipped in case it is not needed or if you don‘t want to control the governor with a separate channel, e. g. if your transmitter does not provide enough free channels. By skipping the assignment the internal governor function will use a different operating mode that allows to control it by the throttle channel if you like. When used in an electric model the internal governor is controlled by the throttle channel in general. In this case the assignment can be skipped anyway, as it will have no effect.
	* Finally ~~at Menu Point J~~ you ~~have to~~ assign the channel that is used to ~~activate/deactivate~~ the AttitudeControl (only ~~when~~ you've installed the PROEDITION Upgrade on your device). Again this can be skipped if not needed or if you don‘t want to use a separate channel. AttitudeControl can still be used then. In this case the channel for the tail gyro ~~sensitivity (set at Menu Point F)~~ is used to ~~switch~~ AttitudeControl or ~~you~~ can ~~enable it~~ separately using the Bank Switch feature, see the section about using AttitudeControl for further details.</p>		* Finally, you can assign the channel that is used to engage the AttitudeControl/rescue stabilization (only available you've installed the PROEDITION Upgrade on your device). Again this can be skipped if not needed or if you don‘t want to use a separate channel or in case you have no more free channels left). AttitudeControl can still be used then. In this case the channel for the tail gyro gain is used to engage AttitudeControl or can be enabled separately using the Bank Switch feature. Please see the section about using AttitudeControl for further details.</p>
	<br />		<br />
	{\|class="gallery" style="font-style: italic"		{\|class="gallery" style="font-style: italic"

FuzzyBot: Importing a new version from external source

2019-07-09T15:19:42Z

Importing a new version from external source

← Older revision		Revision as of 15:19, 9 July 2019
Line 198:		Line 198:
	<br />		<br />

	==~~Point A -~~ Receiver type==		==Receiver type==
	In order to detect the connected receiver type make sure the receiver is bound to the transmitter and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBPlusFblV5:Radio_System/en\|Radio System]]. Press the "Scan" button to start automatic receiver detection routine. The Status-LED on the device and the display will indicate which type the system is scanning for at the moment. When a valid input signal was detected the receiver type will be set automatically and a ~~small~~ dialog will appear ~~and ask you~~ how to proceed with function assignments ~~in case~~ a ~~single-line~~ receiver is used or the system will restart ~~when a Standard receiver is used~~. When detection fails ~~the system will stay at menu point A. In this case~~ once again make sure your receiver is connected properly to MICROBEAST PLUS, bound to the transmitter and sending out control signals and try again.<br />		In order to detect the connected receiver type make sure the receiver is bound to the transmitter and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBPlusFblV5:Radio_System/en\|Radio System]]. Press the "Scan" button to start automatic receiver detection routine. The Status-LED on the device and the display will indicate which type the system is scanning for at the moment. When a valid input signal was detected the receiver type will be set automatically and a dialog will appear in case a single-line receiver is used. This asks how to proceed with function assignments. When a Standard receiver is used the system will restart directly and you can leave the setup screen as there . When detection fails once again make sure your receiver is connected properly to MICROBEAST PLUS, bound to the transmitter and sending out control signals and try again.<br />
	<br />		<br />
	{\|class="gallery" style="font-style: italic"		{\|class="gallery" style="font-style: italic"