Manuals:MBPlusFblV5:Setupmenu E - Revision history

Shornstein at 19:56, 10 July 2019

2019-07-10T19:56:02Z

← Older revision		Revision as of 19:56, 10 July 2019
Line 47:		Line 47:

	=Setup with StudioXm= <!--T:8-->		=Setup with StudioXm= <!--T:8-->
	1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Increase!" In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />		1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Increase!" In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. Repeat this for the other direction. Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.<br />
	<br />		<br />
	<div class="iosgallery">		<div class="iosgallery">
	<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20037.PNG">		<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20037.PNG">
	<div class="iostext">Stick moved ~~to the right~~, deflection not enough</div>		<div class="iostext">Stick moved into one direction, deflection not enough</div>
	</div>		</div>
	<div class="iosgallery">		<div class="iosgallery">
	<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20038.PNG">		<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20038.PNG">
	<div class="iostext">Stick moved ~~to the right~~, maximum position reached</div>		<div class="iostext">Stick moved into one direction, maximum position reached</div>
	</div>		</div>
	<br />		<br />
	<br />		<br />
	2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.'''<br />		2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.'''<br />
			<br />
			<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20038.PNG">
			<div class="iostext">Stick moved left, but label shows right</div>
			</div>
			<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20041.PNG">
			<div class="iostext">Stick moved left, label shows left</div>
			</div>
			<br />
	<br />		<br />
	3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />		3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />

Shornstein at 19:47, 10 July 2019

2019-07-10T19:47:45Z

← Older revision		Revision as of 19:47, 10 July 2019
Line 46:		Line 46:
	<br />		<br />

	=Setup with ~~StudioX~~= <!--T:7-->		=Setup with StudioXm= <!--T:8-->
	~~To activate~~ the rudder ~~adjustments click~~ the '''~~Adjust button~~''' in the ~~corresponding table row (when using~~ the '''~~Wizard~~''' ~~function this~~ will ~~be done automatically~~ when ~~you click~~ the ~~'''Next button''' after adjusting Menu Point D~~).<br />		1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Increase!" In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />
	<br />		<br />
	~~[[File~~:~~SetupEF~~.~~png\|x250px]]~~<br />		<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20037.PNG">
			<div class="iostext">Stick moved to the right, deflection not enough</div>
			</div>
			<div class="iosgallery">
			<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20038.PNG">
			<div class="iostext">Stick moved to the right, maximum position reached</div>
			</div>
	<br />		<br />
	<br />		<br />
	1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Move stick to max. position! Check Status LED." In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position.)<br />		2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.'''<br />
	~~<br />~~
	2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above~~. When you move the rudder stick~~ check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.<br />
	<br />		<br />
	3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />		3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />
	<br />		<br />
	{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<~~br /~~>		<div class="iosgallery">
	<br />		<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20040.PNG">
	~~'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis~~.~~''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction~~. ~~So later in flight the gyro will stop the helicopter from unwanted movement.}}<br~~ />		<div class="iostext"></div>
	~~<br~~ />		</div>

	~~=Setup with StudioXm= <!--T:8~~-->
	<~~br /~~>
	~~[[File:SetupEF_mobile.png\|x250px]]~~
	<br />
	<~~br />~~
	1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Increase!" In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />
	<br />		<br />
	2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.'''<br />
	~~<br />~~
	3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />
	<br />		<br />
	{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the app and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />		{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the app and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />

Shornstein at 07:54, 12 January 2018

2018-01-12T07:54:54Z

← Older revision		Revision as of 07:54, 12 January 2018
Line 1:		Line 1:
	<translate>		<translate>
	<!--T:11-->		<!--T:11-->
	~~{{TOC_MBPlusV5\|Manuals:MBPlusFblV5:Setupmenu_D/en\|Manuals:MBPlusFblV5:Setupmenu_G/en}}~~
	{{DISPLAYTITLE:SETUP MENU E & F - Rudder limits and control direction\|noerror}}		{{DISPLAYTITLE:SETUP MENU E & F - Rudder limits and control direction\|noerror}}
			{{TOC_MBPlusV5\|Manuals:MBPlusFblV5:Setupmenu_D/en\|Manuals:MBPlusFblV5:Setupmenu_G/en\|SETUPMENU}}
	__TOC__		__TOC__
	<br />		<br />

Shornstein at 06:55, 12 January 2018

2018-01-12T06:55:58Z

← Older revision		Revision as of 06:55, 12 January 2018
Line 1:		Line 1:
	<translate>		<translate>
	<!--T:11-->		<!--T:11-->
			{{TOC_MBPlusV5\|Manuals:MBPlusFblV5:Setupmenu_D/en\|Manuals:MBPlusFblV5:Setupmenu_G/en}}
	{{DISPLAYTITLE:SETUP MENU E & F - Rudder limits and control direction\|noerror}}		{{DISPLAYTITLE:SETUP MENU E & F - Rudder limits and control direction\|noerror}}
	~~{{TOC_MBPlusV5}}~~
	__TOC__		__TOC__
	<br />		<br />

Shornstein at 14:49, 30 November 2017

2017-11-30T14:49:00Z

← Older revision		Revision as of 14:49, 30 November 2017
Line 39:		Line 39:
	2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left) reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />		2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left) reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />
	<br />		<br />
	3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when ~~reaching~~ the end position.)<br />		3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />
	<br />		<br />
	{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />		{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />
	<br />		<br />
	'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement. Here the LED will light up in '''blue''' color when you turn the helicopter to the '''right''' and light up in '''red''' when you turn it to the '''left'''. ~~This is to give~~ you a little reminder when you need to do the setup later on the field ~~and you can't rememeber what color stands for what direction~~!}}<br />		'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement. Here the LED will light up in '''blue''' color when you turn the helicopter to the '''right''' and light up in '''red''' when you turn it to the '''left'''. So you can get a little reminder when you do not know which is the correct stick direction to setup, when you need to do the setup later on the field!}}<br />
	<br />		<br />

Line 58:		Line 58:
	3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />		3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />
	<br />		<br />
	{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />		{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />
	<br />		<br />
	'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement.}}<br />		'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement.}}<br />
Line 68:		Line 68:
	<br />		<br />
	<br />		<br />
	1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Increase!" In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when ~~reaching~~ the end position.)<br />		1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Increase!" In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />
	<br />		<br />
	2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.'''<br />		2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.'''<br />

Shornstein at 14:35, 30 November 2017

2017-11-30T14:35:46Z

← Older revision		Revision as of 14:35, 30 November 2017
Line 39:		Line 39:
	2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left) reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />		2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left) reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />
	<br />		<br />
	3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when ~~raching~~ the end position.)<br />		3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position.)<br />
	<br />		<br />
	{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />		{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />
	<br />		<br />
	'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement. Here the LED will light up in '''blue''' color when you turn the helicopter to the '''right''' and light up in '''red''' when you turn it to the '''left'''. So you ~~can get~~ a little reminder ~~when you do not know which is the correct stick direction to setup,~~ when you need to do the setup later on the field!}}<br />		'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement. Here the LED will light up in '''blue''' color when you turn the helicopter to the '''right''' and light up in '''red''' when you turn it to the '''left'''. This is to give you a little reminder when you need to do the setup later on the field and you can't rememeber what color stands for what direction!}}<br />
	<br />		<br />

Line 68:		Line 68:
	<br />		<br />
	<br />		<br />
	1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Increase!" In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when ~~raching~~ the end position.)<br />		1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Increase!" In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position.)<br />
	<br />		<br />
	2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.'''<br />		2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.'''<br />

Shornstein: Marked this version for translation

2017-11-30T10:38:55Z

Marked this version for translation

← Older revision		Revision as of 10:38, 30 November 2017
Line 1:		Line 1:
	<translate>		<translate>
			<!--T:11-->
	{{DISPLAYTITLE:SETUP MENU E & F - Rudder limits and control direction\|noerror}}		{{DISPLAYTITLE:SETUP MENU E & F - Rudder limits and control direction\|noerror}}
	{{TOC_MBPlusV5}}		{{TOC_MBPlusV5}}

Shornstein at 10:38, 30 November 2017

2017-11-30T10:38:36Z

← Older revision		Revision as of 10:38, 30 November 2017
Line 1:		Line 1:
	<translate>		<translate>
	~~<!--T:1-->~~
	{{DISPLAYTITLE:SETUP MENU E & F - Rudder limits and control direction\|noerror}}		{{DISPLAYTITLE:SETUP MENU E & F - Rudder limits and control direction\|noerror}}
	{{TOC_MBPlusV5}}		{{TOC_MBPlusV5}}

Shornstein at 10:32, 30 November 2017

2017-11-30T10:32:22Z

← Older revision		Revision as of 10:32, 30 November 2017
Line 35:		Line 35:

	==SETUP MENU F - Rudder control direction== <!--T:6-->		==SETUP MENU F - Rudder control direction== <!--T:6-->
	1. Move the rudder stick and check the rudder direction on the helicopter. If the stick is moving the servo into the wrong direction~~, '''~~use the servo reverse function of your transmitter and reverse the rudder channel to set stick control direction correctly.~~'''~~<br />		1. Move the rudder stick and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly.<br />
	<br />		<br />
	2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. When the display is inverted (red = right and blue = left)~~, '''~~reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />		2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left) reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />
	<br />		<br />
	3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />		3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />
Line 52:		Line 52:
	<br />		<br />
	<br />		<br />
	1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Move stick to max. position! Check Status LED." In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when ~~raching~~ the end position.)<br />		1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Move stick to max. position! Check Status LED." In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position.)<br />
	<br />		<br />
	2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above ~~and adjust~~ the servo ~~limit by changing~~ the ~~values in~~ the ~~two adjustment boxes for each~~ direction. ~~To do so, carefully use~~ the rudder stick to move the ~~servo~~ to the ~~endpoint~~ (~~watch out to not jam~~ the ~~servo~~) ~~and increase/decrease~~ the ~~endpoint as necessary~~.<br />		2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above. When you move the rudder stick check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.<br />
	<br />		<br />
	3. ~~When you move the rudder stick check the rudder direction on the helicopter. '''If the stick is moving~~ the servo ~~into~~ the ~~wrong direction use the servo reverse function of your transmitter and reverse~~ the ~~rudder channel to set stick control~~ direction ~~correctly~~.~~'''<br />~~		3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />
	~~<br />~~
	~~4. Finally set the rudder direction of the MICROBEAST PLUS gyro: When you move~~ the rudder stick~~/servo~~ to ~~the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you~~ move the ~~rudder stick~~ to the ~~<span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted~~ (~~red = right and blue = left), reverse~~ the ~~display (internal control direction~~) ~~by choosing either ''normal'' or ''inverted'' in~~ the ~~software~~.~~'''~~<br />
	<br />		<br />
	{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />		{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />
Line 65:		Line 63:
	<br />		<br />

	=Setup with ~~StudioX~~= <!--T:8-->		=Setup with StudioXm= <!--T:8-->
			<br />
			[[File:SetupEF_mobile.png\|x250px]]
			<br />
			<br />
			1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Increase!" In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />
	<br />		<br />
			2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.'''<br />
	<br />		<br />
	~~[[File:SetupEF_mobile~~.~~png\|x250px]]~~<br />		3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />
	<br />		<br />
			{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the app and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />
			<br />
			'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement.}}<br />
	<br />		<br />

Line 84:		Line 91:
	Image:Tailgyro_wrong.png\|When moving the tail to the right by hand (nose of the heli to the left), the gyro steers to the left and so the tail will move even further!		Image:Tailgyro_wrong.png\|When moving the tail to the right by hand (nose of the heli to the left), the gyro steers to the left and so the tail will move even further!
	</gallery>		</gallery>
	Please note: This shows ~~only~~ an example for the ALIGN T-Rex 500 helicopter. Actually the tail pitch slider may move to a different position on your helicopter. This mainly depends on how the tail blade grips are controlled and how the tail mechanics is constructed in general. Check the manual of your helicopter to find out which directions the rudder must move on your helicopter.<br />		Please note: This only shows an example for the ALIGN T-Rex 500 helicopter. Actually the tail pitch slider may move to a different position on your helicopter. This mainly depends on how the tail blade grips are controlled and how the tail mechanics is constructed in general. Check the manual of your helicopter to find out which directions the rudder must move on your helicopter.<br />
	<br />		<br />
	<br />		<br />

	</translate>		</translate>

Shornstein: Marked this version for translation

2017-11-27T16:16:00Z

Marked this version for translation

← Older revision		Revision as of 16:16, 27 November 2017
Line 1:		Line 1:
	<translate>		<translate>
			<!--T:1-->
	{{DISPLAYTITLE:SETUP MENU E & F - Rudder limits and control direction\|noerror}}		{{DISPLAYTITLE:SETUP MENU E & F - Rudder limits and control direction\|noerror}}
	{{TOC_MBPlusV5}}		{{TOC_MBPlusV5}}
Line 5:		Line 6:
	<br />		<br />

			<!--T:2-->
	Next we have to setup the rudder gyro. For this we set the limits of the tail pitch control and the control directions, so the gyro will not move the servo further than allowed and in correct direction. In first line the rudder limits are necessary to prevent the gyro from moving the servo over the mechanical limits and damaging the servo. But when adjusting the limits please note that the optimum throw is not necessarily determined by the maximum possible control travel of the tail pitch slider. When the tail mechanics allow a very high range of pitch it may be advisable to adjust the limits based on the maximum allowed angle of attack of the tail rotor blades that will not lead to an aerodynamic stall of the blades. Such stalls can cause very bad stopping behavior like overshooting of the tail when stopping from rotation and can also cause bad tail response to rudder stick input when performing directional changes. Keep this in mind when adjusting the tail rotor endpoints. Check the helicopter‘s manual to find out how much tail pitch is useful and where to set end points.<br />		Next we have to setup the rudder gyro. For this we set the limits of the tail pitch control and the control directions, so the gyro will not move the servo further than allowed and in correct direction. In first line the rudder limits are necessary to prevent the gyro from moving the servo over the mechanical limits and damaging the servo. But when adjusting the limits please note that the optimum throw is not necessarily determined by the maximum possible control travel of the tail pitch slider. When the tail mechanics allow a very high range of pitch it may be advisable to adjust the limits based on the maximum allowed angle of attack of the tail rotor blades that will not lead to an aerodynamic stall of the blades. Such stalls can cause very bad stopping behavior like overshooting of the tail when stopping from rotation and can also cause bad tail response to rudder stick input when performing directional changes. Keep this in mind when adjusting the tail rotor endpoints. Check the helicopter‘s manual to find out how much tail pitch is useful and where to set end points.<br />
	<br />		<br />
	<br />		<br />

	=Mechanical setup of the rudder servo=		=Mechanical setup of the rudder servo= <!--T:3-->
	In the following of this setup step you will be asked to connect the rudder servo to MICROBEAST PLUS. When doing so plug the servo connector into CH4 output at the device. Watch out for correct polarity, the black or brown minus wire must be the clostest to the bottom of the device.<br />		In the following of this setup step you will be asked to connect the rudder servo to MICROBEAST PLUS. When doing so plug the servo connector into CH4 output at the device. Watch out for correct polarity, the black or brown minus wire must be the clostest to the bottom of the device.<br />
	[[Image:Rudderservo_connection.png\|200px\|none]]<br />		[[Image:Rudderservo_connection.png\|200px\|none]]<br />
Line 21:		Line 23:
	<br />		<br />

	=Adjustment on the device=		=Adjustment on the device= <!--T:4-->
	Using the EasySetup adjustment on the device this setup is separated in two Menu Points. At Menu Point E we set the rudder limits, at Menu Point F we teach the control direction. At first connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above now.<br />		Using the EasySetup adjustment on the device this setup is separated in two Menu Points. At Menu Point E we set the rudder limits, at Menu Point F we teach the control direction. At first connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above now.<br />
	<br />		<br />

	==SETUP MENU E - Rudder limits==		==SETUP MENU E - Rudder limits== <!--T:5-->
	To adjust the servo limits move the rudder stick in one direction until the servo reaches the maximum endpoint without any binding or stall. Release the rudder stick when correct position is reached. If you moved the servo too far you can steer the stick to the opposite direction and move the pitch slider a short way back. Also you can tap the stick briefly to only make minor adjustments. Once the correct endpoint has been found, don‘t move the rudder stick anymore and wait a second for the Status-LED to flash. This will indicate that the new position was stored. (If necessary you can change position as often as you want, but always wait until the Status-LED flashes when finished and proceeding to the next step!)<br />		To adjust the servo limits move the rudder stick in one direction until the servo reaches the maximum endpoint without any binding or stall. Release the rudder stick when correct position is reached. If you moved the servo too far you can steer the stick to the opposite direction and move the pitch slider a short way back. Also you can tap the stick briefly to only make minor adjustments. Once the correct endpoint has been found, don‘t move the rudder stick anymore and wait a second for the Status-LED to flash. This will indicate that the new position was stored. (If necessary you can change position as often as you want, but always wait until the Status-LED flashes when finished and proceeding to the next step!)<br />
	<br />		<br />
Line 32:		Line 34:
	When both positions have been set skip to the next Menu Point F by pushing the button on the device briefly.		When both positions have been set skip to the next Menu Point F by pushing the button on the device briefly.

	==SETUP MENU F - Rudder control direction==		==SETUP MENU F - Rudder control direction== <!--T:6-->
	1. Move the rudder stick and check the rudder direction on the helicopter. If the stick is moving the servo into the wrong direction, '''use the servo reverse function of your transmitter and reverse the rudder channel to set stick control direction correctly.'''<br />		1. Move the rudder stick and check the rudder direction on the helicopter. If the stick is moving the servo into the wrong direction, '''use the servo reverse function of your transmitter and reverse the rudder channel to set stick control direction correctly.'''<br />
	<br />		<br />
Line 44:		Line 46:
	<br />		<br />

	=Setup with StudioX=		=Setup with StudioX= <!--T:7-->
	To activate the rudder adjustments click the '''Adjust button''' in the corresponding table row (when using the '''Wizard''' function this will be done automatically when you click the '''Next button''' after adjusting Menu Point D).<br />		To activate the rudder adjustments click the '''Adjust button''' in the corresponding table row (when using the '''Wizard''' function this will be done automatically when you click the '''Next button''' after adjusting Menu Point D).<br />
	<br />		<br />
Line 63:		Line 65:
	<br />		<br />

	=Setup with StudioX=		=Setup with StudioX= <!--T:8-->
	<br />		<br />
	<br />		<br />
Line 70:		Line 72:
	<br />		<br />

	=Extra info: Why setting stick endpoints?=		=Extra info: Why setting stick endpoints?= <!--T:9-->
	This ensures that control range of the radio system matches the internal range of MICROBEAST PLUS. Later when setting the control style you can adjust how fast your helicopter should turn around the vertical axis. To get reproducable results you have to match your radio to the system!<br />		This ensures that control range of the radio system matches the internal range of MICROBEAST PLUS. Later when setting the control style you can adjust how fast your helicopter should turn around the vertical axis. To get reproducable results you have to match your radio to the system!<br />
	<br />		<br />
	<br />		<br />

	=Extra info: How the gyro works!=		=Extra info: How the gyro works!= <!--T:10-->
	The gyro always tries to steer in the opposite direction of the rotation that is applied to the helicopter. If you move the helicopter by hand around its vertical axis, the gyro must actuate a rudder servo movement to compensate this rotation. If for example you move the nose of the helicopter to the left (tail moving to the right), the gyro has to steer right the same way as you would steer right with the rudder stick, so that the tail is pushed back to the left.}}		The gyro always tries to steer in the opposite direction of the rotation that is applied to the helicopter. If you move the helicopter by hand around its vertical axis, the gyro must actuate a rudder servo movement to compensate this rotation. If for example you move the nose of the helicopter to the left (tail moving to the right), the gyro has to steer right the same way as you would steer right with the rudder stick, so that the tail is pushed back to the left.}}
	<br />		<br />