Manuals:MBPlusFblV5:Setupmenu H - Revision history

Shornstein at 09:21, 19 July 2018

2018-07-19T09:21:59Z

← Older revision		Revision as of 09:21, 19 July 2018
Line 7:		Line 7:

	<!--T:2-->		<!--T:2-->
	At SETUP MENU point H we trim the servo center positions so that each servo horn forms an exact 90 degrees angle with the adjustment linkage. This is necessary as usually you will not be able to attach the servo horns in exact center position to the servo. '''After all servos have been trimmed do not proceed to the next menu point yet.''' ~~With active~~ trimming adjust the linkage rods according to your helicopter's manual. ~~The~~ swashplate should ~~now~~ be at the midpoint and perpendicular to the main shaft and the rotor blades should have 0 degrees of pitch. Always work this out from bottom (servos) to top (blade grips). ~~Also~~ don‘t forget to level and phase the swashplate driver in the correct way ~~(if it‘s adjustable)!~~ At 0 degrees of pitch the swash driver arms must be horizontal and the linkage balls of the blade grips ~~have to~~ be perpendicular to the spindle shaft.<br />		At SETUP MENU point H we trim the servo center positions so that each servo horn forms an exact 90 degrees angle with the adjustment linkage. This is necessary as usually you will not be able to attach the servo horns in exact center position to the servo. '''After all servos have been trimmed do not proceed to the next menu point yet.''' After trimming adjust the linkage rods according to your helicopter's manual, so the rotorhead system is set up neutral and allows to have equal movements in all directions. For this the swashplate should be at the midpoint and perpendicular to the main shaft and the rotor blades should have 0 degrees of pitch. Always work this out from bottom (servos) to top (blade grips).<br />
			<br />
			In case your helicopter has a non-DFC rotor head with adjustable swashplate driver also don‘t forget to level and phase the swashplate driver in the correct way. At 0 degrees of pitch the swash driver arms must be horizontal and the linkage balls of the blade grips must be perpendicular to the spindle shaft.<br />
	<br />		<br />
	{\|		{\|
Line 18:		Line 20:

	=Adjustment on the device= <!--T:3-->		=Adjustment on the device= <!--T:3-->
	Initially when the trimming is 0 on all servos the Status LED will be off. Attach the servo horns on the servos at their true center position, so that you get roughly equal throws to both direction. Mount the servo horns so that they form ~~as much as possible~~ a 90 degrees angle to the linkage rod. Then in the next step you electronically fine trim every single servo‘s center position, as usually mounting the servo horn at exact 90 degrees will not work out perfectly depending on the servo‘s gear train and the servo horn.<br />		Initially when the trimming is 0 on all servos the Status LED will be off. Attach the servo horns on the servos at their true center position, so that you get roughly equal throws to both direction. Mount the servo horns so that they form a 90 degrees angle to the linkage rod as close as possible. Then in the next step you electronically fine trim every single servo‘s center position, as usually mounting the servo horn at exact 90 degrees will not work out perfectly depending on the servo‘s gear train and the servo horn.<br />
	<br />		<br />
	By tapping the aileron ~~stick~~ you can select one servo after another. Every color of the Status-LED is corresponding to a specific servo channel that is indicating its selection by a short up and down move. Use the rudder stick to change the servo trimming/adjust the center position. You can switch back and forth between the servos as often as you need.<br />		By tapping the '''stick for aileron''' you can '''select one servo after another'''. Every color of the Status-LED is corresponding to a specific servo channel that is indicating its selection by a short up and down move. Use the '''rudder stick''' to change the '''servo trimming/adjust the center position'''. You can switch back and forth between the servos as often as you need.<br />
	<br />		<br />
	{\|cellpadding="4" cellspacing="0" border="1"		{\|cellpadding="4" cellspacing="0" border="1"
Line 35:		Line 37:
	\| style="color:white; background: linear-gradient(to right, #FF3300, black, #0066FF)" \| red/blue \|\| CH7 – elevator servo(2) (90° eCCPM only)		\| style="color:white; background: linear-gradient(to right, #FF3300, black, #0066FF)" \| red/blue \|\| CH7 – elevator servo(2) (90° eCCPM only)
	\|}<br />		\|}<br />
	~~<br />~~
	~~<br />~~

	~~=Setup with StudioX= <!--T:4-->~~
	To activate the servo trim adjustments click the '''Adjust button''' in the corresponding table row (when using the '''Wizard''' function this will be done automatically when you click the '''Next button''' after adjusting Menu Point G). For your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary. Finally click the '''Save button''' or '''Next button''' (when using the '''Wizard''' function) to finish the servo trim adjustment.<br />
	~~<br />~~
	~~[[File:SetupH.PNG\|x250px]]<br />~~
	<br />		<br />
	<br />		<br />

Shornstein at 07:56, 12 January 2018

2018-01-12T07:56:49Z

← Older revision		Revision as of 07:56, 12 January 2018
Line 2:		Line 2:
	<!--T:1-->		<!--T:1-->
	{{DISPLAYTITLE:SETUP MENU H - Servo trim\|noerror}}		{{DISPLAYTITLE:SETUP MENU H - Servo trim\|noerror}}
	{{TOC_MBPlusV5\|Manuals:MBPlusFblV5:Setupmenu_G/en\|Manuals:MBPlusFblV5:Setupmenu_I/en}}		{{TOC_MBPlusV5\|Manuals:MBPlusFblV5:Setupmenu_G/en\|Manuals:MBPlusFblV5:Setupmenu_I/en\|SETUPMENU}}
	__TOC__		__TOC__
	<br />		<br />

Shornstein at 06:59, 12 January 2018

2018-01-12T06:59:15Z

← Older revision		Revision as of 06:59, 12 January 2018
Line 2:		Line 2:
	<!--T:1-->		<!--T:1-->
	{{DISPLAYTITLE:SETUP MENU H - Servo trim\|noerror}}		{{DISPLAYTITLE:SETUP MENU H - Servo trim\|noerror}}
	{{TOC_MBPlusV5}}		{{TOC_MBPlusV5\|Manuals:MBPlusFblV5:Setupmenu_G/en\|Manuals:MBPlusFblV5:Setupmenu_I/en}}
	__TOC__		__TOC__
	<br />		<br />

Shornstein at 12:46, 30 November 2017

2017-11-30T12:46:11Z

← Older revision		Revision as of 12:46, 30 November 2017
Line 46:		Line 46:

	=Setup with StudioXm= <!--T:5-->		=Setup with StudioXm= <!--T:5-->
	When the servo trim screen appears, for your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo using the '''+''' and '''-''' buttons so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary~~. Finally click the '''Save button''' or '''Next button''' (when using the '''Wizard''' function) to finish the servo trim adjustment~~.<br />		When the servo trim screen appears, for your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo using the '''+''' and '''-''' buttons so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary.<br />
	<br />		<br />
	[[File:SetupHm.png\|x250px]]<br />		[[File:SetupHm.png\|x250px]]<br />

Shornstein: Marked this version for translation

2017-11-30T12:31:40Z

Marked this version for translation

← Older revision		Revision as of 12:31, 30 November 2017
Line 1:		Line 1:
	<translate>		<translate>
			<!--T:1-->
	{{DISPLAYTITLE:SETUP MENU H - Servo trim\|noerror}}		{{DISPLAYTITLE:SETUP MENU H - Servo trim\|noerror}}
	{{TOC_MBPlusV5}}		{{TOC_MBPlusV5}}
Line 5:		Line 6:
	<br />		<br />

			<!--T:2-->
	At SETUP MENU point H we trim the servo center positions so that each servo horn forms an exact 90 degrees angle with the adjustment linkage. This is necessary as usually you will not be able to attach the servo horns in exact center position to the servo. '''After all servos have been trimmed do not proceed to the next menu point yet.''' With active trimming adjust the linkage rods according to your helicopter's manual. The swashplate should now be at the midpoint and perpendicular to the main shaft and the rotor blades should have 0 degrees of pitch. Always work this out from bottom (servos) to top (blade grips). Also don‘t forget to level and phase the swashplate driver in the correct way (if it‘s adjustable)! At 0 degrees of pitch the swash driver arms must be horizontal and the linkage balls of the blade grips have to be perpendicular to the spindle shaft.<br />		At SETUP MENU point H we trim the servo center positions so that each servo horn forms an exact 90 degrees angle with the adjustment linkage. This is necessary as usually you will not be able to attach the servo horns in exact center position to the servo. '''After all servos have been trimmed do not proceed to the next menu point yet.''' With active trimming adjust the linkage rods according to your helicopter's manual. The swashplate should now be at the midpoint and perpendicular to the main shaft and the rotor blades should have 0 degrees of pitch. Always work this out from bottom (servos) to top (blade grips). Also don‘t forget to level and phase the swashplate driver in the correct way (if it‘s adjustable)! At 0 degrees of pitch the swash driver arms must be horizontal and the linkage balls of the blade grips have to be perpendicular to the spindle shaft.<br />
	<br />		<br />
Line 15:		Line 17:
	<br />		<br />

	=Adjustment on the device=		=Adjustment on the device= <!--T:3-->
	Initially when the trimming is 0 on all servos the Status LED will be off. Attach the servo horns on the servos at their true center position, so that you get roughly equal throws to both direction. Mount the servo horns so that they form as much as possible a 90 degrees angle to the linkage rod. Then in the next step you electronically fine trim every single servo‘s center position, as usually mounting the servo horn at exact 90 degrees will not work out perfectly depending on the servo‘s gear train and the servo horn.<br />		Initially when the trimming is 0 on all servos the Status LED will be off. Attach the servo horns on the servos at their true center position, so that you get roughly equal throws to both direction. Mount the servo horns so that they form as much as possible a 90 degrees angle to the linkage rod. Then in the next step you electronically fine trim every single servo‘s center position, as usually mounting the servo horn at exact 90 degrees will not work out perfectly depending on the servo‘s gear train and the servo horn.<br />
	<br />		<br />
Line 36:		Line 38:
	<br />		<br />

	=Setup with StudioX=		=Setup with StudioX= <!--T:4-->
	To activate the servo trim adjustments click the '''Adjust button''' in the corresponding table row (when using the '''Wizard''' function this will be done automatically when you click the '''Next button''' after adjusting Menu Point G). For your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary. Finally click the '''Save button''' or '''Next button''' (when using the '''Wizard''' function) to finish the servo trim adjustment.<br />		To activate the servo trim adjustments click the '''Adjust button''' in the corresponding table row (when using the '''Wizard''' function this will be done automatically when you click the '''Next button''' after adjusting Menu Point G). For your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary. Finally click the '''Save button''' or '''Next button''' (when using the '''Wizard''' function) to finish the servo trim adjustment.<br />
	<br />		<br />
Line 43:		Line 45:
	<br />		<br />

	=Setup with StudioXm=		=Setup with StudioXm= <!--T:5-->
	When the servo trim screen appears, for your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo using the '''+''' and '''-''' buttons so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary. Finally click the '''Save button''' or '''Next button''' (when using the '''Wizard''' function) to finish the servo trim adjustment.<br />		When the servo trim screen appears, for your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo using the '''+''' and '''-''' buttons so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary. Finally click the '''Save button''' or '''Next button''' (when using the '''Wizard''' function) to finish the servo trim adjustment.<br />
	<br />		<br />

Shornstein at 12:31, 30 November 2017

2017-11-30T12:31:24Z

← Older revision		Revision as of 12:31, 30 November 2017
Line 25:		Line 25:
	\|style="color:white; background-color:black" \| off \|\| all zero		\|style="color:white; background-color:black" \| off \|\| all zero
	\|-		\|-
	\| style="color:white; background-color:#CC66CC" \| purple \|\| ~~CH 1~~ – elevator servo		\| style="color:white; background-color:#CC66CC" \| purple \|\| CH1 – elevator servo
	\|-		\|-
	\|style="color:white; background-color:#FF3300" \| red \|\|~~CH 2~~ – aileron(1) servo		\|style="color:white; background-color:#FF3300" \| red \|\|CH2 – aileron(1) servo
	\|-		\|-
	\| style="color:white; background-color:#0066FF" \| blue \|\| ~~CH 3~~ – aileron(2) / pitch servo (mCCPM)		\| style="color:white; background-color:#0066FF" \| blue \|\| CH3 – aileron(2) / pitch servo (mCCPM)
	\|-		\|-
	\| style="color:white; background: linear-gradient(to right, #FF3300, black, #0066FF)" \| red/blue \|\| ~~CH 7~~ – elevator servo(2) (90° eCCPM only)		\| style="color:white; background: linear-gradient(to right, #FF3300, black, #0066FF)" \| red/blue \|\| CH7 – elevator servo(2) (90° eCCPM only)
	\|}<br />		\|}<br />
	<br />		<br />

Shornstein at 12:30, 30 November 2017

2017-11-30T12:30:26Z

← Older revision		Revision as of 12:30, 30 November 2017
Line 5:		Line 5:
	<br />		<br />

	At SETUP MENU point H we trim the servo center positions so that each servo horn forms an exact 90 degrees angle with the adjustment linkage. This is necessary as usually you will not be able to attach the servo horns in exact center position to the servo. '''After all servos have been trimmed do not proceed to the next menu point yet.''' With active trimming adjust the linkage rods according to your helicopter manual. The swashplate should now be at the midpoint and perpendicular to the main shaft and the rotor blades should have 0 degrees of pitch. Always work this out from bottom (servos) to top (blade grips). Also don‘t forget to level and phase the swashplate driver in the correct way (if it‘s adjustable)! At 0 degrees of pitch the swash driver arms must be horizontal and the linkage balls of the blade grips have to be perpendicular to the spindle shaft.<br />		At SETUP MENU point H we trim the servo center positions so that each servo horn forms an exact 90 degrees angle with the adjustment linkage. This is necessary as usually you will not be able to attach the servo horns in exact center position to the servo. '''After all servos have been trimmed do not proceed to the next menu point yet.''' With active trimming adjust the linkage rods according to your helicopter's manual. The swashplate should now be at the midpoint and perpendicular to the main shaft and the rotor blades should have 0 degrees of pitch. Always work this out from bottom (servos) to top (blade grips). Also don‘t forget to level and phase the swashplate driver in the correct way (if it‘s adjustable)! At 0 degrees of pitch the swash driver arms must be horizontal and the linkage balls of the blade grips have to be perpendicular to the spindle shaft.<br />
	<br />		<br />
	[[Image:Swashdriver_1.png\|~~600px\|none~~\|border]]~~<br />~~		{\|
	~~<br />~~		\|-
	[[Image:Swashdriver_2.png\|~~600px\|none~~\|border]]<br />		\| [[Image:Swashdriver_1.png\|x120px\|border]]
			\| [[Image:Swashdriver_2.png\|x120px\|border]]
			\|}<br />
	<br />		<br />
	<br />		<br />
Line 18:		Line 20:
	By tapping the aileron stick you can select one servo after another. Every color of the Status-LED is corresponding to a specific servo channel that is indicating its selection by a short up and down move. Use the rudder stick to change the servo trimming/adjust the center position. You can switch back and forth between the servos as often as you need.<br />		By tapping the aileron stick you can select one servo after another. Every color of the Status-LED is corresponding to a specific servo channel that is indicating its selection by a short up and down move. Use the rudder stick to change the servo trimming/adjust the center position. You can switch back and forth between the servos as often as you need.<br />
	<br />		<br />
	{~~{TABLEV5~~\|~~Swashplate servo~~ center trim		{\|cellpadding="4" cellspacing="0" border="1"
	\|CH 1 – elevator servo		\| style="width:100px; text-align:left;" \| '''Status-LED''' \|\| style="text-align:center;" \| '''Servo trim'''
	\|CH 2 – aileron(1) servo		\|-
	\|CH 3 – aileron(2) / pitch servo (mCCPM)		\|style="color:white; background-color:black" \| off \|\| all zero
	\|CH 7 – elevator servo(2) (90° eCCPM only)		\|-
	}}		\| style="color:white; background-color:#CC66CC" \| purple \|\| CH 1 – elevator servo
			\|-
			\|style="color:white; background-color:#FF3300" \| red \|\|CH 2 – aileron(1) servo
			\|-
			\| style="color:white; background-color:#0066FF" \| blue \|\| CH 3 – aileron(2) / pitch servo (mCCPM)
			\|-
			\| style="color:white; background: linear-gradient(to right, #FF3300, black, #0066FF)" \| red/blue \|\| CH 7 – elevator servo(2) (90° eCCPM only)
			\|}<br />
			<br />
	<br />		<br />

Line 29:		Line 39:
	To activate the servo trim adjustments click the '''Adjust button''' in the corresponding table row (when using the '''Wizard''' function this will be done automatically when you click the '''Next button''' after adjusting Menu Point G). For your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary. Finally click the '''Save button''' or '''Next button''' (when using the '''Wizard''' function) to finish the servo trim adjustment.<br />		To activate the servo trim adjustments click the '''Adjust button''' in the corresponding table row (when using the '''Wizard''' function this will be done automatically when you click the '''Next button''' after adjusting Menu Point G). For your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary. Finally click the '''Save button''' or '''Next button''' (when using the '''Wizard''' function) to finish the servo trim adjustment.<br />
	<br />		<br />
	[[File:SetupH.~~png~~\|x250px]]<br />		[[File:SetupH.PNG\|x250px]]<br />
	<br />		<br />
	<br />		<br />

Shornstein: Created page with " {{DISPLAYTITLE:SETUP MENU H - Servo trim|noerror}} {{TOC_MBPlusV5}} TOC
At SETUP MENU point H we trim the servo center positions so that each servo hor..."

2017-11-30T12:16:43Z

Created page with "<translate> {{DISPLAYTITLE:SETUP MENU H - Servo trim|noerror}} {{TOC_MBPlusV5}} __TOC__ At SETUP MENU point H we trim the servo center positions so that each servo hor..."

New page

<translate>
{{DISPLAYTITLE:SETUP MENU H - Servo trim|noerror}}
{{TOC_MBPlusV5}}
__TOC__
 

At SETUP MENU point H we trim the servo center positions so that each servo horn forms an exact 90 degrees angle with the adjustment linkage. This is necessary as usually you will not be able to attach the servo horns in exact center position to the servo. '''After all servos have been trimmed do not proceed to the next menu point yet.''' With active trimming adjust the linkage rods according to your helicopter manual. The swashplate should now be at the midpoint and perpendicular to the main shaft and the rotor blades should have 0 degrees of pitch. Always work this out from bottom (servos) to top (blade grips). Also don‘t forget to level and phase the swashplate driver in the correct way (if it‘s adjustable)! At 0 degrees of pitch the swash driver arms must be horizontal and the linkage balls of the blade grips have to be perpendicular to the spindle shaft. 
 
[[Image:Swashdriver_1.png|600px|none|border]] 
 
[[Image:Swashdriver_2.png|600px|none|border]] 
 
 

=Adjustment on the device=
Initially when the trimming is 0 on all servos the Status LED will be off. Attach the servo horns on the servos at their true center position, so that you get roughly equal throws to both direction. Mount the servo horns so that they form as much as possible a 90 degrees angle to the linkage rod. Then in the next step you electronically fine trim every single servo‘s center position, as usually mounting the servo horn at exact 90 degrees will not work out perfectly depending on the servo‘s gear train and the servo horn. 
 
By tapping the aileron stick you can select one servo after another. Every color of the Status-LED is corresponding to a specific servo channel that is indicating its selection by a short up and down move. Use the rudder stick to change the servo trimming/adjust the center position. You can switch back and forth between the servos as often as you need. 
 
{{TABLEV5|Swashplate servo center trim
|CH 1 – elevator servo
|CH 2 – aileron(1) servo
|CH 3 – aileron(2) / pitch servo (mCCPM)
|CH 7 – elevator servo(2) (90° eCCPM only)
}}
 

=Setup with StudioX=
To activate the servo trim adjustments click the '''Adjust button''' in the corresponding table row (when using the '''Wizard''' function this will be done automatically when you click the '''Next button''' after adjusting Menu Point G). For your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary. Finally click the '''Save button''' or '''Next button''' (when using the '''Wizard''' function) to finish the servo trim adjustment. 
 
[[File:SetupH.png|x250px]] 
 
 

=Setup with StudioXm=
When the servo trim screen appears, for your reference the servos will briefly move up and down once one after another in the given order CH1 to CH3 (CH7) so you can identify them easily. Trim each servo using the '''+''' and '''-''' buttons so that the servo horn forms an exact 90 degrees angle with the linkage rod. Then make the mechanical adjustment for the linkages as described above if necessary. Finally click the '''Save button''' or '''Next button''' (when using the '''Wizard''' function) to finish the servo trim adjustment. 
 
[[File:SetupHm.png|x250px]] 
 
 

</translate>