Manuals:MBPlusFblV52:Radio System - Revision history

Shornstein: Marked this version for translation

2023-02-23T10:37:54Z

Marked this version for translation

← Older revision		Revision as of 10:37, 23 February 2023
Line 49:		Line 49:
	<br />		<br />

	<!--T:9-->		== Single wire without telemetry == <!--T:9-->
	~~== Single wire without telemetry ==~~
	* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS		* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS
	* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.		* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.
Line 84:		Line 83:
	<br />		<br />

	<!--T:7-->		== Single wire with telemetry == <!--T:7-->
	~~== Single wire with telemetry ==~~
	Receivers with bidirectional telemetry uplink (Spektrum® SRXL2 & Jeti® EXBUS) must be connected to the pin board at the side of MICROBEAST PLUS. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - Order nr. BXA76403. Voltage is the first pin from the left, Signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />		Receivers with bidirectional telemetry uplink (Spektrum® SRXL2 & Jeti® EXBUS) must be connected to the pin board at the side of MICROBEAST PLUS. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - Order nr. BXA76403. Voltage is the first pin from the left, Signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
	* When '''telemetry is not in use''', the throttle servo or ESC is connected to the '''[AIL\|CH5]''' port.		* When '''telemetry is not in use''', the throttle servo or ESC is connected to the '''[AIL\|CH5]''' port.

Shornstein at 10:37, 23 February 2023

2023-02-23T10:37:45Z

← Older revision		Revision as of 10:37, 23 February 2023
Line 63:		Line 63:

	<!--T:10-->		<!--T:10-->
	'''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />		[[File:Warning.png\|18px\|sub]] '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />
	<br />		<br />
	<br />		<br />

	<!--T:6-->		<!--T:6-->
	Remote receivers (Spektrum® DSMX/DSM2, JR® DMSS, ALIGN® iBus) can be directly connected to the white pin board at the side of MICROBEAST ULTRA. Here the receiver will be powered with a stabilized voltage of 3.3 Volts! Voltage is the first pin from the front/right, Minus is the second pin from the right, Signal is connected at the third pin from the right.<br />		'''Remote receivers''' (Spektrum® DSMX/DSM2, JR® DMSS, ALIGN® iBus) can be directly connected to the white pin board at the side of MICROBEAST ULTRA. Here the receiver will be powered with a stabilized voltage of 3.3 Volts! Voltage is the first pin from the front/right, Minus is the second pin from the right, Signal is connected at the third pin from the right.<br />
	<br />		<br />
	'''Please note:''' MICROBEAST PLUS doesn't support connecting more than one remote satellite at a time!<br />		'''Please note:''' MICROBEAST PLUS doesn't support connecting more than one remote satellite at a time!<br />
Line 87:		Line 87:
	== Single wire with telemetry ==		== Single wire with telemetry ==
	Receivers with bidirectional telemetry uplink (Spektrum® SRXL2 & Jeti® EXBUS) must be connected to the pin board at the side of MICROBEAST PLUS. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - Order nr. BXA76403. Voltage is the first pin from the left, Signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />		Receivers with bidirectional telemetry uplink (Spektrum® SRXL2 & Jeti® EXBUS) must be connected to the pin board at the side of MICROBEAST PLUS. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - Order nr. BXA76403. Voltage is the first pin from the left, Signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
			* When '''telemetry is not in use''', the throttle servo or ESC is connected to the '''[AIL\|CH5]''' port.
			* When using a telemetry receiver and an '''ESC with telemetry''' data connector, the ESC is connected to '''[ELE\|DI1]'''. The data signal of the ESC is connected to '''[AIL\|CH5]'''. (You will get further information about connecting the speed controller and setting up telemetry on the next page!)
			* You can connect a power supply (second BEC wire, battery) to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit (except the port [RUD\|PIT\|AUX]; please do not connect anything here!).<br />
			<br />
			[[File:Warning.png\|18px\|sub]] '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />
			<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 AR6610T en.png\| x150px]]		\|[[Image:SRXL2 AR6610T en.png\| x150px]]
Line 94:		Line 100:
	<br />		<br />
	<br />		<br />
	To connect a SRXL2 remote receiver like '''SPM4650/SPM4651T''' it is necessary to '''INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />		To connect a '''SRXL2 remote receiver''' like '''SPM4650/SPM4651T''' it is necessary to '''INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 Satellite en.png\| x180px]]		\|[[Image:SRXL2 Satellite en.png\| x180px]]
Line 103:		Line 109:
	\|}		\|}
	{{WARNING_QUOTE\|'''Never connect the 4-pin receiver connector to MICROBEAST ULTRA without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />		{{WARNING_QUOTE\|'''Never connect the 4-pin receiver connector to MICROBEAST ULTRA without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
	~~<br />~~
	~~<br />~~
	* When '''telemetry is not in use''', the throttle servo or ESC is connected to the '''[AIL\|CH5]''' port.
	* When using a telemetry receiver and an '''ESC with telemetry''' data connector, the ESC is connected to '''[ELE\|DI1]'''. The data signal of the ESC is connected to '''[AIL\|CH5]'''. (You will get further information about connecting the speed controller and setting up telemetry on the next page!)
	* You can connect a power supply (second BEC wire, battery) to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit (except the port [RUD\|PIT\|AUX]; please do not connect anything here!).<br />
	<br /> '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />
	<br />		<br />
	<br />		<br />
	</translate>		</translate>

Shornstein at 10:32, 23 February 2023

2023-02-23T10:32:22Z

← Older revision		Revision as of 10:32, 23 February 2023
Line 8:		Line 8:

	<!--T:11-->		<!--T:11-->
	MICROBEAST PLUS can work with a lot of different receiver types and radio brands, especially with different types of radio signal protocols. Depending on which signal protocol and receiver you intend to use, the wiring layout may vary. In the following you can see all supported protocols and specific wiring schemes for each receiver type. '''Ensure a tight fit of the connectors.''' The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Anyhow, especially when using a receiver with single wire output it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.<br />		MICROBEAST PLUS can work with a lot of different receiver types and radio brands, especially with different types of radio signal protocols. Depending on which signal protocol and receiver you intend to use, the wiring layout may vary. In the following you can see all supported protocols and specific wiring schemes for each receiver type.<br />
			<br />
			[[File:Warning.png\|18px\|sub]] '''Ensure a tight fit of the connectors.''' The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Anyhow, especially when using a receiver with single wire output it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.<br />
	<br />		<br />
	<br />		<br />

	=Standard receiver= <!--T:4-->		=Standard receiver= <!--T:4-->
	A ~~conventional~~ receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each output to one control function of MICROBEAST PLUS by using one ~~connection~~ wire for each function. The 5 control functions (wires) are: Aileron, Elevator, Rudder, Collective pitch and Gyro gain~~. Connect each wire to the corresponding servo output at the receiver which you like to use for the specific function~~. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to each ~~channel testwise~~!<br />		A receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each servo output to one control function of MICROBEAST PLUS by using one wire for each function. The 5 control functions (wires) are: Aileron, Elevator, Rudder, Collective pitch and Gyro gain. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to test what each output is used for!<br />
	<br />		<br />
	{\|cellspacing = "20"		{\|cellspacing = "20"
	\|style="text-align:center;"\| [[Image:Standard_RX.png\|250px]]		\|style="text-align:center;"\| [[Image:Standard_RX.png\|250px]]
	\|}<br />		\|}<br />
	Here we show connection layouts for two common radio brands. Note that this is only exemplary, ~~the channel output of your transmitter can by different even when using a radio of this brand. And~~ you can use any radio system on the market, not only these two brands!		Here we show connection layouts for two common radio brands. Note that this is only exemplary, you can use any radio system on the market, not only these two brands! Anyhow, make sure that you connect the wires to the correct functions as mentioned above.
	{\|cellspacing = "20"		{\|cellspacing = "20"
	\|[[Image:Spektrum_RX.png\|x100px]]		\|[[Image:Spektrum_RX.png\|x100px]]
Line 24:		Line 26:
	\|}<br />		\|}<br />
	{{QUOTE\|		{{QUOTE\|
	* The wires for rudder, pitch and gyro are signal wires. ~~They~~ must be placed on the same receiver side as the the ~~both~~ orange wires from aileron and elevator!		* The wires for rudder, pitch and gyro are all signal wires. Although some have different color, they must be placed on the same receiver side as the the orange wires from aileron and elevator!
	* You must connect all 5 functions/wires to the receiver. When you don't connect all wires, the system will not finish initialization sequence!		* You must connect all 5 functions/wires to the receiver. When you don't connect all wires, the system will not finish initialization sequence!
	* The throttle servo/speed controller is connected to the receiver's throttle output. ~~Using~~ the headspeed governor function of MICROBEAST PLUS is not possible in combination with a Standard receiver!}}<br />		* The throttle servo/speed controller is connected to the receiver's throttle output. So using the headspeed '''governor function''' of MICROBEAST PLUS is '''not possible''' in combination with a Standard receiver!}}<br />
	<br />		<br />
	<br />		<br />
Line 39:		Line 41:
	MICROBEAST PLUS supports the following systems '''without telemetry''':		MICROBEAST PLUS supports the following systems '''without telemetry''':
	* Spektrum® DSMX/DSM2 remote receivers and receivers with SRXL output		* Spektrum® DSMX/DSM2 remote receivers and receivers with SRXL output
	* Futaba® SBUS		* Futaba® SBUS (1 & 2)
	* Multiplex® SRXL		* Multiplex® SRXL
	* JR® X-Bus (Mode B)		* JR® X-Bus (Mode B)
Line 66:		Line 68:

	<!--T:6-->		<!--T:6-->
	Remote receivers (Spektrum® DSMX/DSM2, JR® DMSS, ALIGN® iBus) can be directly connected to the white pin board at the side of MICROBEAST ULTRA. Here the receiver will be powered with a stabilized voltage of 3.3 Volts! Voltage is the first pin from the front/right, ~~minus~~ is the second pin from the right, ~~signal~~ is connected at the third pin from the right.<br />		Remote receivers (Spektrum® DSMX/DSM2, JR® DMSS, ALIGN® iBus) can be directly connected to the white pin board at the side of MICROBEAST ULTRA. Here the receiver will be powered with a stabilized voltage of 3.3 Volts! Voltage is the first pin from the front/right, Minus is the second pin from the right, Signal is connected at the third pin from the right.<br />
	<br />		<br />
	'''Please note:''' MICROBEAST PLUS ~~does not~~ support connecting more than one remote satellite at a time!<br />		'''Please note:''' MICROBEAST PLUS doesn't support connecting more than one remote satellite at a time!<br />
	<br />		<br />
	{\|cellspacing="20" style="text-align:center;"		{\|cellspacing="20" style="text-align:center;"
Line 84:		Line 86:
	<!--T:7-->		<!--T:7-->
	== Single wire with telemetry ==		== Single wire with telemetry ==
	Receivers with bidirectional telemetry uplink (Spektrum® SRXL2 & Jeti® EXBUS) must be connected to the pin board at the side of MICROBEAST PLUS. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - ~~order~~ nr. BXA76403. Voltage is the first pin from the left, ~~signal~~ is connected at the third pin from the left. Minus is the second pin from the front/right.<br />		Receivers with bidirectional telemetry uplink (Spektrum® SRXL2 & Jeti® EXBUS) must be connected to the pin board at the side of MICROBEAST PLUS. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - Order nr. BXA76403. Voltage is the first pin from the left, Signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 AR6610T en.png\| x150px]]		\|[[Image:SRXL2 AR6610T en.png\| x150px]]
Line 103:		Line 105:
	<br />		<br />
	<br />		<br />
	* When telemetry is not in use, the throttle servo or ESC is connected to the '''[AIL\|CH5]''' port.		* When '''telemetry is not in use''', the throttle servo or ESC is connected to the '''[AIL\|CH5]''' port.
	* When using a telemetry receiver and an ESC with telemetry data connector, the ESC is connected to '''[ELE\|DI1]'''. The data signal of the ESC is connected to '''[AIL\|CH5]'''. (You will get further information about connecting the speed controller and setting up telemetry on the next page!)		* When using a telemetry receiver and an '''ESC with telemetry''' data connector, the ESC is connected to '''[ELE\|DI1]'''. The data signal of the ESC is connected to '''[AIL\|CH5]'''. (You will get further information about connecting the speed controller and setting up telemetry on the next page!)
	* You can connect a power supply (second BEC wire, battery) to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit (except the port [RUD\|PIT\|AUX]; please do not connect anything here!).<br />		* You can connect a power supply (second BEC wire, battery) to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit (except the port [RUD\|PIT\|AUX]; please do not connect anything here!).<br />
	<br /> '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />		<br /> '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />

Shornstein at 14:49, 17 February 2023

2023-02-17T14:49:09Z

← Older revision		Revision as of 14:49, 17 February 2023
Line 31:		Line 31:

	=Receivers with single wire output= <!--T:5-->		=Receivers with single wire output= <!--T:5-->
	A single-line receiver transmits ~~all channels/~~all control functions over one single connection wire to MICROBEAST PLUS. This is done by packing all ~~stick~~ outputs to a digital data paket or by chaining the signals. ~~At the moment~~ MICROBEAST PLUS supports the following systems: ~~Multiplex® SRLX,~~ Spektrum® ~~SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti®~~ EXBUS~~, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM.<br />~~		A single-line receiver transmits all control functions over one single connection wire to MICROBEAST PLUS. This is done by packing all channel outputs into a digital data paket or by chaining the signals onto one line.<br />
			MICROBEAST PLUS supports the following systems '''with telemetry uplink''':
			* Spektrum® SRXL2
			* JETI® EXBUS
			* GRAUPNER® HOTT
	<br />		<br />
	~~(For Spektrum® SRXL2 or when you like to make use of~~ telemetry ~~data, please connect your receiver as shonw under [[#~~Spektrum® ~~SRXL2~~ / ~~JETI EXBUS~~ receivers ~~for telemetry]]~~.)<br />		MICROBEAST PLUS supports the following systems '''without telemetry''':
			* Spektrum® DSMX/DSM2 remote receivers and receivers with SRXL output
			* Futaba® SBUS
			* Multiplex® SRXL
			* JR® X-Bus (Mode B)
			* Jeti® UDI
			* ALIGN® and FlySky® iBus
			* any SPPM (serial ppm) receiver .<br />
	<br />		<br />

	<!--T:9-->		<!--T:9-->
			== Single wire without telemetry ==
	* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS		* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS
	* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.		* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.
	* ~~Alternatively or additionally you~~ can connect a power supply/second BEC wire~~/buffering~~ battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit.<br />		* You can connect a power supply (second BEC wire, battery) to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit (except the port [RUD\|PIT\|AUX]; please do not connect anything here!).<br />
	<br />		<br />
	{\|cellspacing="20" style="text-align:center;"		{\|cellspacing="20" style="text-align:center;"
Line 53:		Line 65:
	<br />		<br />

	~~=Remote satellite (Spektrum® DSM/JR® DMSS/ALIGN® iBus)=~~ <!--T:6-->		<!--T:6-->
	~~A special type of single-line receiver is the remote satellite. These~~ receivers ~~usually serve as additional receiving unit in combination with a~~ (bigger) main receiver to provide a more robust and fail safe radio system. With MICROBEAST PLUS you can use such receivers as stand alone receiving unit to achieve a small and light weight radio system for small sized rc models. MICROBEAST PLUS supports the following systems: Spektrum® DSM2~~, Spektrum® DSMX~~, JR® DMSS ~~and~~ ALIGN® iBus~~. The remote receiver~~ can be directly connected to the white pin board at the side of MICROBEAST ~~PLUS~~. Here the receiver will be powered with a stabilized voltage of 3.3 Volts~~. Alternatively if you own~~ the ~~optional available Spektrum® satellite adapter (Order Nr. BXA76009) you can connect~~ the ~~receiver at~~ the ~~front~~ pin ~~board to~~ the ~~[DI1] digital input~~, ~~just like most other single-wire receivers. This allows to keep~~ the ~~white~~ pin ~~board free for connecting a sensor~~.<br />		Remote receivers (Spektrum® DSMX/DSM2, JR® DMSS, ALIGN® iBus) can be directly connected to the white pin board at the side of MICROBEAST ULTRA. Here the receiver will be powered with a stabilized voltage of 3.3 Volts! Voltage is the first pin from the front/right, minus is the second pin from the right, signal is connected at the third pin from the right.<br />
	<br />		<br />
	'''Please note:''' MICROBEAST PLUS does not support connecting more than one remote satellite at a time!<br />		'''Please note:''' MICROBEAST PLUS does not support connecting more than one remote satellite at a time!<br />
Line 66:		Line 78:
	\|}		\|}
	<br />		<br />
	When using a speed controller with BEC, the power will be distributed from [CH5] input to receiver and servos. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port.<br />		{{WARNING_QUOTE\|'''Using a remote satellite is only recommended for small rc models (helicopters of 450 size or smaller).''' Due to the design, one single receiving unit is more prone to radio interference and can result in reduced transmission range!}}<br />
	~~<br />~~
	{{WARNING_QUOTE\|'''Using a remote satellite is only recommended for small rc ~~modells like~~ helicopters of 450 size or smaller.''' Due to the design, one single receiving unit is more prone to radio interference and can result in reduced transmission range.}}<br />
	<br />		<br />
	<br />		<br />

	~~=Telemetry receivers Spektrum® SRXL2 / JETI EXBUS=~~ <!--T:7-->		<!--T:7-->
	~~'''~~Spektrum® SRXL2~~''' receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. All of these receivers~~ must be connected to the pin board at the side of MICROBEAST PLUS.~~<br />~~		== Single wire with telemetry ==
	~~<br />~~		Receivers with bidirectional telemetry uplink (Spektrum® SRXL2 & Jeti® EXBUS) must be connected to the pin board at the side of MICROBEAST PLUS. To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
	~~Also when you want to use a '''JETI receiver with EXBUS''' connection for telemtry support, you must connect the receiver to the side port of MICROBEAST PLUS as shown below.<br />~~
	~~<br />~~
	When using a speed controller with BEC, the power will be distributed from [CH5] or [DI1] input to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Feeding power directly into the receiver is not possible as the voltage connector on MICROBEAST PLUS side is only oneway!'''<br />
	~~<br />~~
	~~<br />~~
	~~<u>'''Receivers with standard connector'''</u><br />~~
	~~<br />~~
	To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. ~~Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below!~~ Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 AR6610T en.png\| x150px]]		\|[[Image:SRXL2 AR6610T en.png\| x150px]]
Line 89:		Line 91:
	\|}		\|}
	<br />		<br />
	~~<u>'''SRXL2 satellite receivers'''</u><br />~~
	<br />		<br />
	To connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />		To connect a SRXL2 remote receiver like '''SPM4650/SPM4651T''' it is necessary to '''INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 Satellite en.png\| x180px]]		\|[[Image:SRXL2 Satellite en.png\| x180px]]
Line 99:		Line 100:
	\| Modified 4-pin SRXL connector		\| Modified 4-pin SRXL connector
	\|}		\|}
	{{WARNING_QUOTE\|'''Never connect the 4-pin receiver connector to MICROBEAST ~~PLUS~~ without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />		{{WARNING_QUOTE\|'''Never connect the 4-pin receiver connector to MICROBEAST ULTRA without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
			<br />
			<br />
			* When telemetry is not in use, the throttle servo or ESC is connected to the '''[AIL\|CH5]''' port.
			* When using a telemetry receiver and an ESC with telemetry data connector, the ESC is connected to '''[ELE\|DI1]'''. The data signal of the ESC is connected to '''[AIL\|CH5]'''. (You will get further information about connecting the speed controller and setting up telemetry on the next page!)
			* You can connect a power supply (second BEC wire, battery) to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit (except the port [RUD\|PIT\|AUX]; please do not connect anything here!).<br />
			<br /> '''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />
	<br />		<br />
	<br />		<br />
	</translate>		</translate>

Shornstein at 07:17, 3 May 2022

2022-05-03T07:17:57Z

← Older revision		Revision as of 07:17, 3 May 2022
Line 80:		Line 80:
	<br />		<br />
	<br />		<br />
	''Receivers with standard connector''<br />		<u>'''Receivers with standard connector'''</u><br />
	<br />		<br />
	To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />		To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
Line 89:		Line 89:
	\|}		\|}
	<br />		<br />
	''SRXL2 satellite receivers''<br />		<u>'''SRXL2 satellite receivers'''</u><br />
	<br />		<br />
	To connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />		To connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />

Shornstein at 06:58, 3 May 2022

2022-05-03T06:58:05Z

← Older revision		Revision as of 06:58, 3 May 2022
Line 72:		Line 72:
	<br />		<br />

	=Spektrum® SRXL2 / JETI EXBUS ~~receivers for telemetry~~= <!--T:7-->		=Telemetry receivers Spektrum® SRXL2 / JETI EXBUS= <!--T:7-->
	'''Spektrum® SRXL2''' receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. All of these receivers must be connected to the pin board at the side of MICROBEAST PLUS.<br />		'''Spektrum® SRXL2''' receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. All of these receivers must be connected to the pin board at the side of MICROBEAST PLUS.<br />
	<br />		<br />
	Also when you want to use a '''JETI receiver with EXBUS''' connection for telemtry support, you must connect the receiver to the side port of MICROBEAST PLUS as shown below.<br />		Also when you want to use a '''JETI receiver with EXBUS''' connection for telemtry support, you must connect the receiver to the side port of MICROBEAST PLUS as shown below.<br />
	<br />		<br />
	When using a speed controller with BEC, the power will be distributed from [CH5] input ~~of MICROBEAST PLUS~~ to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Feeding power directly into the receiver is not possible as the voltage connector on MICROBEAST PLUS side is only oneway!'''<br />		When using a speed controller with BEC, the power will be distributed from [CH5] or [DI1] input to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Feeding power directly into the receiver is not possible as the voltage connector on MICROBEAST PLUS side is only oneway!'''<br />
	<br />		<br />
	<br />		<br />
	''Receivers with standard connector''<br />		''Receivers with standard connector''<br />
	<br />		<br />
	To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST ~~plug~~. We offer an special adapter if needed - order nr. BXA76403. Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />		To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 AR6610T en.png\| x150px]]		\|[[Image:SRXL2 AR6610T en.png\| x150px]]

Shornstein at 13:50, 5 April 2022

2022-04-05T13:50:23Z

← Older revision		Revision as of 13:50, 5 April 2022
Line 30:		Line 30:
	<br />		<br />

	=Receivers with single wire output ~~(single-line receivers)~~= <!--T:5-->		=Receivers with single wire output= <!--T:5-->
	A single-line receiver transmits all channels (control functions~~) by~~ one single connection wire to MICROBEAST PLUS. This is done by packing all ~~channel output data~~ to a digital data paket or by chaining the ~~servo~~ signals. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® ~~EXBus~~, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM<br />		A single-line receiver transmits all channels/all control functions over one single connection wire to MICROBEAST PLUS. This is done by packing all stick outputs to a digital data paket or by chaining the signals. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBUS, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM.<br />
			<br />
	<~~!--T:8--~~>		(For Spektrum® SRXL2 or when you like to make use of telemetry data, please connect your receiver as shonw under [[#Spektrum® SRXL2 / JETI EXBUS receivers for telemetry]].)<br />
	~~{{QUOTE\|There are single-line receivers available that supply additional servo outputs. In combination with MICROBEAST PLUS~~ you ~~only have~~ to ~~treat such receivers as single-line receivers if you really~~ use ~~the single-line function. If you~~ connect ~~the~~ receiver ~~by using the standard 5-wire layout~~ as ~~shown above, such receiver has to be considered as "Standard receiver"~~.}}<br />
	<br />		<br />

Line 40:		Line 39:
	* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS		* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS
	* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.		* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.
	* Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit.		* Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit.<br />
			<br />
	{\|cellspacing="20" style="text-align:center;"		{\|cellspacing="20" style="text-align:center;"
	~~\|[[Image:Singleline_RX.png \| x150px]]~~
	\|[[Image:Singleline_RX_3.png \| x150px]]		\|[[Image:Singleline_RX_3.png \| x150px]]
	\|- style="text-align:center; font-size:75%;"		\|- style="text-align:center; font-size:75%;"
	\| ~~Wiring layout for single-line receivers~~		\| Single-line receiver<br /> with additional servo output channels
	~~\| Alternative wiring layout for single~~-line receiver<br /> with additional servo output channels
	\|}		\|}
	<br />		<br />
Line 74:		Line 72:
	<br />		<br />

	=Spektrum® SRXL2 ~~receiver~~= <!--T:7-->		=Spektrum® SRXL2 / JETI EXBUS receivers for telemetry= <!--T:7-->
	~~Spektrum~~ SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. ~~Anyways, the output signal~~ of ~~those receiver~~ must ~~always~~ be connected to the pin board at the side of MICROBEAST PLUS.<br />		'''Spektrum® SRXL2''' receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. All of these receivers must be connected to the pin board at the side of MICROBEAST PLUS.<br />
			<br />
			Also when you want to use a '''JETI receiver with EXBUS''' connection for telemtry support, you must connect the receiver to the side port of MICROBEAST PLUS as shown below.<br />
	<br />		<br />
	When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Feeding power directly into the receiver is not possible as the voltage connector on MICROBEAST PLUS side is only oneway!'''<br />		When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Feeding power directly into the receiver is not possible as the voltage connector on MICROBEAST PLUS side is only oneway!'''<br />
	<br />		<br />
	<br />		<br />
	~~In order to~~ connect a receiver with standard servo connectors, i.e. the '''AR6610T''', you need ~~the SRXL2 receiver~~ adapter. Also you ~~may~~ use ~~the~~ governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />		''Receivers with standard connector''<br />
			<br />
			To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST plug. We offer an special adapter if needed - order nr. BXA76403. Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 AR6610T en.png\| x150px]]		\|[[Image:SRXL2 AR6610T en.png\| x150px]]
Line 86:		Line 88:
	\| SRXL2 receiver with standard servo connector and adapter		\| SRXL2 receiver with standard servo connector and adapter
	\|}		\|}
	~~In order to~~ connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />		<br />
			''SRXL2 satellite receivers''<br />
			<br />
			To connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 Satellite en.png\| x180px]]		\|[[Image:SRXL2 Satellite en.png\| x180px]]
			\|[[Image:SRXL2 rx kabel.png\| 200px]]
	\|- style="text-align:center; font-size:75%;"		\|- style="text-align:center; font-size:75%;"
	\| SRXL2 satellite receiver with modified satellite connector		\| SRXL2 satellite receiver with modified satellite connector
			\| Modified 4-pin SRXL connector
	\|}		\|}
	{{WARNING_QUOTE\|'''Never connect the 4-~~wire~~ receiver connector to MICROBEAST PLUS without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />		{{WARNING_QUOTE\|'''Never connect the 4-pin receiver connector to MICROBEAST PLUS without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
	~~{\|cellspacing="50" style="text-align:center;"~~		<br />
	~~\|[[Image:SRXL2 Satellite wrong en.png\| x120px]]~~
	~~\|[[Image:SRXL2 Satellite correct en.png\| x120px]]~~
	\|}<br />
	<br />		<br />
	</translate>		</translate>

Shornstein at 11:04, 8 March 2022

2022-03-08T11:04:06Z

← Older revision		Revision as of 11:04, 8 March 2022
Line 75:		Line 75:

	=Spektrum® SRXL2 receiver= <!--T:7-->		=Spektrum® SRXL2 receiver= <!--T:7-->
	Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as ~~reeceivers~~ with a special 4-wire connector. ~~The~~ output signal ~~of any~~ of those receiver must be connected to the pin board at the side of MICROBEAST PLUS.~~<br /> '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!~~<br />		Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. Anyways, the output signal of those receiver must always be connected to the pin board at the side of MICROBEAST PLUS.<br />
	<br />		<br />
	When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not ~~recommended to connect power to~~ the ~~receiver directly~~!<br />		When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Feeding power directly into the receiver is not possible as the voltage connector on MICROBEAST PLUS side is only oneway!'''<br />
	<br />		<br />
	In order to connect a receiver with standard servo connectors, i.e. the AR6610T, you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below!<br />		<br />
			In order to connect a receiver with standard servo connectors, i.e. the '''AR6610T''', you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 AR6610T en.png\| x150px]]		\|[[Image:SRXL2 AR6610T en.png\| x150px]]
Line 85:		Line 86:
	\| SRXL2 receiver with standard servo connector and adapter		\| SRXL2 receiver with standard servo connector and adapter
	\|}		\|}
	~~<br />~~		In order to connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />
	In order to connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to ~~interchange the plus and minus wires (usually black&orange)~~ of the 4-~~wire~~ receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 Satellite en.png\| x180px]]		\|[[Image:SRXL2 Satellite en.png\| x180px]]
Line 92:		Line 92:
	\| SRXL2 satellite receiver with modified satellite connector		\| SRXL2 satellite receiver with modified satellite connector
	\|}		\|}
			{{WARNING_QUOTE\|'''Never connect the 4-wire receiver connector to MICROBEAST PLUS without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 Satellite wrong en.png\| x120px]]		\|[[Image:SRXL2 Satellite wrong en.png\| x120px]]
	\|[[Image:SRXL2 Satellite correct en.png\| x120px]]		\|[[Image:SRXL2 Satellite correct en.png\| x120px]]
	\|}<br />		\|}<br />
	{{WARNING_QUOTE\|'''Never connect the 4-wire receiver connector to MICROBEAST PLUS in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
	~~<br />~~
	<br />		<br />
	</translate>		</translate>

Shornstein at 09:24, 25 March 2021

2021-03-25T09:24:57Z

← Older revision		Revision as of 09:24, 25 March 2021
Line 75:		Line 75:

	=Spektrum® SRXL2 receiver= <!--T:7-->		=Spektrum® SRXL2 receiver= <!--T:7-->
	Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as ~~remote satellites~~ with a special 4-wire connector. The output signal of any of those receiver must be connected to the pin board at the side of MICROBEAST PLUS.<br /> '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!<br />		Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as reeceivers with a special 4-wire connector. The output signal of any of those receiver must be connected to the pin board at the side of MICROBEAST PLUS.<br /> '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!<br />
	<br />		<br />
	When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />		When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />
Line 86:		Line 86:
	\|}		\|}
	<br />		<br />
	In order to connect a SRXL2 ~~remote satellite~~ like '''SPM4650 it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />		In order to connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 Satellite en.png\| x180px]]		\|[[Image:SRXL2 Satellite en.png\| x180px]]

Shornstein at 07:59, 1 October 2020

2020-10-01T07:59:23Z

← Older revision		Revision as of 07:59, 1 October 2020
Line 8:		Line 8:

	<!--T:11-->		<!--T:11-->
	MICROBEAST PLUS can work with a lot of different receiver types and radio brands ~~and~~ especially with different types of radio signal protocols. Depending on which signal protocol and receiver you intend to use the wiring layout may vary. In the following you can see all supported protocols and specific wiring schemes for each receiver type. '''Ensure a tight fit of the connectors.''' The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Anyhow, especially when using a receiver with single wire output it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.<br />		MICROBEAST PLUS can work with a lot of different receiver types and radio brands, especially with different types of radio signal protocols. Depending on which signal protocol and receiver you intend to use, the wiring layout may vary. In the following you can see all supported protocols and specific wiring schemes for each receiver type. '''Ensure a tight fit of the connectors.''' The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Anyhow, especially when using a receiver with single wire output it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.<br />
	<br />		<br />
	<br />		<br />

	=Standard receiver= <!--T:4-->		=Standard receiver= <!--T:4-->
	A conventional receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each ~~servo~~ output to one ~~specific~~ control function ~~at the~~ MICROBEAST PLUS using one connection wire for each function. ~~You have these~~ 5 ~~input~~ functions (wires): Aileron, Elevator, Rudder, Collective pitch and ~~gyro~~ gain. ~~Simply connect~~ each wire to the corresponding ~~channel~~ output ~~port~~ at the receiver which you like to use for the specific function. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to each channel testwise!<br />		A conventional receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each output to one control function of MICROBEAST PLUS by using one connection wire for each function. The 5 control functions (wires) are: Aileron, Elevator, Rudder, Collective pitch and Gyro gain. Connect each wire to the corresponding servo output at the receiver which you like to use for the specific function. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to each channel testwise!<br />
	<br />		<br />
	{\|cellspacing = "20"		{\|cellspacing = "20"
	\|style="text-align:center;"\| [[Image:Standard_RX.png\|250px]]		\|style="text-align:center;"\| [[Image:Standard_RX.png\|250px]]
	\|}<br />		\|}<br />
	Here we show connection layouts for two common radio brands. Note that this is only exemplary, the channel output of your transmitter can by different even when using a radio of this brand. And you can use any ~~other~~ radio system on the market ~~together with MICROBEAST PLUS when using the servo output channels of the receiver~~, not only these two brands!		Here we show connection layouts for two common radio brands. Note that this is only exemplary, the channel output of your transmitter can by different even when using a radio of this brand. And you can use any radio system on the market, not only these two brands!
	{\|cellspacing = "20"		{\|cellspacing = "20"
	\|[[Image:Spektrum_RX.png\|x100px]]		\|[[Image:Spektrum_RX.png\|x100px]]
Line 25:		Line 25:
	{{QUOTE\|		{{QUOTE\|
	* The wires for rudder, pitch and gyro are signal wires. They must be placed on the same receiver side as the the both orange wires from aileron and elevator!		* The wires for rudder, pitch and gyro are signal wires. They must be placed on the same receiver side as the the both orange wires from aileron and elevator!
	* You must connect all 5 functions/wires to the receiver. When you ~~do not~~ connect all wires the system will not finish initialization sequence!		* You must connect all 5 functions/wires to the receiver. When you don't connect all wires, the system will not finish initialization sequence!
	* The throttle servo/speed controller is connected to the receiver's throttle output. Using the ~~Governor~~ function of MICROBEAST PLUS ~~therefore~~ is not possible in combination with a Standard receiver.}}<br />		* The throttle servo/speed controller is connected to the receiver's throttle output. Using the headspeed governor function of MICROBEAST PLUS is not possible in combination with a Standard receiver!}}<br />
	<br />		<br />
	<br />		<br />

	=Receivers with single wire output (single-line receivers)= <!--T:5-->		=Receivers with single wire output (single-line receivers)= <!--T:5-->
	~~With a~~ single-line receiver all channels (control functions) ~~are transmitted~~ by one single connection wire to MICROBEAST PLUS. This is done by packing all channel output data to a data paket or by chaining the servo signals ~~to one output port~~. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBus, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM<br />		A single-line receiver transmits all channels (control functions) by one single connection wire to MICROBEAST PLUS. This is done by packing all channel output data to a digital data paket or by chaining the servo signals. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBus, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM<br />

	<!--T:8-->		<!--T:8-->
	{{QUOTE\|There are single-line receivers available that supply additional ~~single channel connectors/~~servo outputs. In combination with MICROBEAST PLUS you only have to treat such receivers as single-line receivers if you really use the single-line function. If you connect the receiver by using the standard 5-~~plug~~ layout, such receiver has to be considered as Standard receiver ~~in the following and as shown above~~.}}<br />		{{QUOTE\|There are single-line receivers available that supply additional servo outputs. In combination with MICROBEAST PLUS you only have to treat such receivers as single-line receivers if you really use the single-line function. If you connect the receiver by using the standard 5-wire layout as shown above, such receiver has to be considered as "Standard receiver".}}<br />
	<br />		<br />

Line 40:		Line 40:
	* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS		* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS
	* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.		* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.
	* Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and to the receiver (in case this has additional servo or battery ports).		* Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit.
	{\|cellspacing="20" style="text-align:center;"		{\|cellspacing="20" style="text-align:center;"
	\|[[Image:Singleline_RX.png \| x150px]]		\|[[Image:Singleline_RX.png \| x150px]]
Line 51:		Line 51:

	<!--T:10-->		<!--T:10-->
	'''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' ~~Note when only connecting~~ power ~~at the receiver, all the current has to flow over one thin wire to the servos~~! If there are no other ports left to (additionally) feed in power, we ~~highly~~ recommend using the MICROBEAST PLUS HD which ~~has~~ an additional high power input ~~to reduce~~ wiring resistance and ~~to serve~~ todays demands for a robust servo power supply.<br />		'''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />
	<br />		<br />
	<br />		<br />