Manuals:MBPlusFblV52:Radio System/en - Revision history

FuzzyBot: Updating to match new version of source page

2023-02-23T10:38:52Z

Updating to match new version of source page

FuzzyBot: Updating to match new version of source page

2022-05-03T07:18:44Z

Updating to match new version of source page

← Older revision		Revision as of 07:18, 3 May 2022
Line 75:		Line 75:
	<br />		<br />
	<br />		<br />
	''Receivers with standard connector''<br />		<u>'''Receivers with standard connector'''</u><br />
	<br />		<br />
	To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />		To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
Line 84:		Line 84:
	\|}		\|}
	<br />		<br />
	''SRXL2 satellite receivers''<br />		<u>'''SRXL2 satellite receivers'''</u><br />
	<br />		<br />
	To connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />		To connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />

FuzzyBot: Updating to match new version of source page

2022-05-03T06:58:23Z

Updating to match new version of source page

← Older revision		Revision as of 06:58, 3 May 2022
Line 27:		Line 27:
	<br />		<br />

	=Receivers with single wire output ~~(single-line receivers)~~=		=Receivers with single wire output=
	A single-line receiver transmits all channels (control functions~~) by~~ one single connection wire to MICROBEAST PLUS. This is done by packing all ~~channel output data~~ to a digital data paket or by chaining the ~~servo~~ signals. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® ~~EXBus~~, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM<br />		A single-line receiver transmits all channels/all control functions over one single connection wire to MICROBEAST PLUS. This is done by packing all stick outputs to a digital data paket or by chaining the signals. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBUS, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM.<br />
			<br />
	~~{{QUOTE\|There are single-line receivers available that supply additional servo outputs. In combination with MICROBEAST PLUS~~ you ~~only have~~ to ~~treat such receivers as single-line receivers if you really~~ use ~~the single-line function. If you~~ connect ~~the~~ receiver ~~by using the standard 5-wire layout~~ as ~~shown above, such receiver has to be considered as "Standard receiver"~~.}}<br />		(For Spektrum® SRXL2 or when you like to make use of telemetry data, please connect your receiver as shonw under [[#Spektrum® SRXL2 / JETI EXBUS receivers for telemetry]].)<br />
	<br />		<br />

	* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS		* The single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS
	* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.		* The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos.
	* Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit.		* Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port and/or to the receiver (in case this has additional servo or battery ports). All servo ports will form a parallel power circuit.<br />
			<br />
	{\|cellspacing="20" style="text-align:center;"		{\|cellspacing="20" style="text-align:center;"
	~~\|[[Image:Singleline_RX.png \| x150px]]~~
	\|[[Image:Singleline_RX_3.png \| x150px]]		\|[[Image:Singleline_RX_3.png \| x150px]]
	\|- style="text-align:center; font-size:75%;"		\|- style="text-align:center; font-size:75%;"
	\| ~~Wiring layout for single-line receivers~~		\| Single-line receiver<br /> with additional servo output channels
	~~\| Alternative wiring layout for single~~-line receiver<br /> with additional servo output channels
	\|}		\|}
	<br />		<br />
Line 68:		Line 67:
	<br />		<br />

	=Spektrum® SRXL2 ~~receiver~~=		=Telemetry receivers Spektrum® SRXL2 / JETI EXBUS=
	~~Spektrum~~ SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. ~~Anyways, the output signal~~ of ~~those receiver~~ must ~~always~~ be connected to the pin board at the side of MICROBEAST PLUS.<br />		'''Spektrum® SRXL2''' receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. All of these receivers must be connected to the pin board at the side of MICROBEAST PLUS.<br />
	<br />		<br />
	~~When using~~ a ~~speed controller~~ with ~~BEC~~, ~~the power will be distributed from [CH5] input of MICROBEAST PLUS to~~ the receiver~~. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery~~ to the ~~[SYS]~~ port~~. '''Feeding power directly into the receiver is not possible as the voltage connector on~~ MICROBEAST PLUS ~~side is only oneway!'''~~<br />		Also when you want to use a '''JETI receiver with EXBUS''' connection for telemtry support, you must connect the receiver to the side port of MICROBEAST PLUS as shown below.<br />
	<br />		<br />
			When using a speed controller with BEC, the power will be distributed from [CH5] or [DI1] input to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Feeding power directly into the receiver is not possible as the voltage connector on MICROBEAST PLUS side is only oneway!'''<br />
	<br />		<br />
	~~In order to~~ connect a receiver with standard servo connectors, i.e. the '''AR6610T''', you need ~~the SRXL2 receiver~~ adapter. Also you ~~may~~ use ~~the~~ governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />		<br />
			''Receivers with standard connector''<br />
			<br />
			To connect a receiver with standard servo connectors, i.e. the SPEKTRUM® '''AR6610T''', '''AR8020T''' or JETI EXBUS receivers, you need an adapter from servo plug to JST-ZH type. We offer a special adapter if needed - order nr. BXA76403. Also you can use our governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 AR6610T en.png\| x150px]]		\|[[Image:SRXL2 AR6610T en.png\| x150px]]
Line 80:		Line 83:
	\| SRXL2 receiver with standard servo connector and adapter		\| SRXL2 receiver with standard servo connector and adapter
	\|}		\|}
	~~In order to~~ connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />		<br />
			''SRXL2 satellite receivers''<br />
			<br />
			To connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 Satellite en.png\| x180px]]		\|[[Image:SRXL2 Satellite en.png\| x180px]]
			\|[[Image:SRXL2 rx kabel.png\| 200px]]
	\|- style="text-align:center; font-size:75%;"		\|- style="text-align:center; font-size:75%;"
	\| SRXL2 satellite receiver with modified satellite connector		\| SRXL2 satellite receiver with modified satellite connector
			\| Modified 4-pin SRXL connector
	\|}		\|}
	{{WARNING_QUOTE\|'''Never connect the 4-~~wire~~ receiver connector to MICROBEAST PLUS without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />		{{WARNING_QUOTE\|'''Never connect the 4-pin receiver connector to MICROBEAST PLUS without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
	~~{\|cellspacing="50" style="text-align:center;"~~		<br />
	~~\|[[Image:SRXL2 Satellite wrong en.png\| x120px]]~~
	~~\|[[Image:SRXL2 Satellite correct en.png\| x120px]]~~
	\|}<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2022-03-08T11:04:33Z

Importing a new version from external source

← Older revision		Revision as of 11:04, 8 March 2022
Line 69:		Line 69:

	=Spektrum® SRXL2 receiver=		=Spektrum® SRXL2 receiver=
	Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as ~~reeceivers~~ with a special 4-wire connector. ~~The~~ output signal ~~of any~~ of those receiver must be connected to the pin board at the side of MICROBEAST PLUS.~~<br /> '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!~~<br />		Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as receivers with a special 4-wire connector. Anyways, the output signal of those receiver must always be connected to the pin board at the side of MICROBEAST PLUS.<br />
	<br />		<br />
	When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not ~~recommended to connect power to~~ the ~~receiver directly~~!<br />		When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Feeding power directly into the receiver is not possible as the voltage connector on MICROBEAST PLUS side is only oneway!'''<br />
	<br />		<br />
	In order to connect a receiver with standard servo connectors, i.e. the AR6610T, you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below!<br />		<br />
			In order to connect a receiver with standard servo connectors, i.e. the '''AR6610T''', you need the SRXL2 receiver adapter. Also you may use the governor sensor adapter BXA76401 but this requires to modify the wiring layout as shown below! Voltage is the first pin from the left, signal is connected at the third pin from the left. Minus is the second pin from the front/right.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 AR6610T en.png\| x150px]]		\|[[Image:SRXL2 AR6610T en.png\| x150px]]
Line 79:		Line 80:
	\| SRXL2 receiver with standard servo connector and adapter		\| SRXL2 receiver with standard servo connector and adapter
	\|}		\|}
	~~<br />~~		In order to connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to INTERCHANGE THE WIRES of the supplied 4-pin receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter. But be very careful! Make sure plus and minus are placed properly! The signal wire is connected at the fourth pin from the front/right, minus ist second pin from the front/right, voltage (+3.3V) is the first pin from the front/right. On satellite side the signal output is on the outer side, the pin next to it is not used, then we have voltage and on the inner side comes minus.<br />
	In order to connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to ~~interchange the plus and minus wires (usually black&orange)~~ of the 4-~~wire~~ receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 Satellite en.png\| x180px]]		\|[[Image:SRXL2 Satellite en.png\| x180px]]
Line 86:		Line 86:
	\| SRXL2 satellite receiver with modified satellite connector		\| SRXL2 satellite receiver with modified satellite connector
	\|}		\|}
			{{WARNING_QUOTE\|'''Never connect the 4-wire receiver connector to MICROBEAST PLUS without modification and in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 Satellite wrong en.png\| x120px]]		\|[[Image:SRXL2 Satellite wrong en.png\| x120px]]
	\|[[Image:SRXL2 Satellite correct en.png\| x120px]]		\|[[Image:SRXL2 Satellite correct en.png\| x120px]]
	\|}<br />		\|}<br />
	{{WARNING_QUOTE\|'''Never connect the 4-wire receiver connector to MICROBEAST PLUS in wrong polarity! This will damage your receiver immediately!''' Check polarity at least twice before connecting the receiver to MICROBEAST PLUS. It is up to you to make sure polarity is correct. We do not assume any liability in case you do it wrong.}}<br />
	~~<br />~~
	<br />		<br />

FuzzyBot: Importing a new version from external source

2021-03-25T09:25:30Z

Importing a new version from external source

← Older revision		Revision as of 09:25, 25 March 2021
Line 69:		Line 69:

	=Spektrum® SRXL2 receiver=		=Spektrum® SRXL2 receiver=
	Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as ~~remote satellites~~ with a special 4-wire connector. The output signal of any of those receiver must be connected to the pin board at the side of MICROBEAST PLUS.<br /> '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!<br />		Spektrum SRXL2 receivers are available in different forms. There exist receivers with standard servo connectors as well as reeceivers with a special 4-wire connector. The output signal of any of those receiver must be connected to the pin board at the side of MICROBEAST PLUS.<br /> '''Please note:''' MICROBEAST PLUS does not support connecting more than one SRXL2 receiver at a time!<br />
	<br />		<br />
	When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />		When using a speed controller with BEC, the power will be distributed from [CH5] input of MICROBEAST PLUS to the receiver. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. It is not recommended to connect power to the receiver directly!<br />
Line 80:		Line 80:
	\|}		\|}
	<br />		<br />
	In order to connect a SRXL2 ~~remote satellite~~ like '''SPM4650 it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />		In order to connect a SRXL2 receiver like '''SPM4650/SPM4651T it is necessary to interchange the plus and minus wires (usually black&orange) of the 4-wire receiver connector'''. In this configuration you can directly plug in the receiver without the need for an extra adapter.<br />
	{\|cellspacing="50" style="text-align:center;"		{\|cellspacing="50" style="text-align:center;"
	\|[[Image:SRXL2 Satellite en.png\| x180px]]		\|[[Image:SRXL2 Satellite en.png\| x180px]]

FuzzyBot: Importing a new version from external source

2020-10-01T08:01:43Z

Importing a new version from external source

← Older revision		Revision as of 08:01, 1 October 2020
Line 45:		Line 45:
	<br />		<br />

	'''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' ~~Note when only connecting~~ power ~~at the receiver, all the current has to flow over one thin wire to the servos~~! If there are no other ports left to (additionally) feed in power, we ~~highly~~ recommend using the MICROBEAST PLUS HD which ~~has~~ an additional high power input ~~to reduce~~ wiring resistance and ~~to serve~~ todays demands for a robust servo power supply.<br />		'''When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port or receiver.''' Adding additional power wires is highly recommended! If there are no other ports left to additionally feed in power, we recommend using the MICROBEAST PLUS HD which comes witch an additional high power input. This reduces wiring resistance and serves todays demands for a robust servo power supply.<br />
	<br />		<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2020-10-01T08:01:23Z

Importing a new version from external source

← Older revision		Revision as of 08:01, 1 October 2020
Line 28:		Line 28:

	=Receivers with single wire output (single-line receivers)=		=Receivers with single wire output (single-line receivers)=
	~~With a~~ single-line receiver all channels (control functions) ~~are transmitted~~ by one single connection wire to MICROBEAST PLUS. This is done by packing all channel output data to a data paket or by chaining the servo signals ~~to one output port~~. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBus, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM<br />		A single-line receiver transmits all channels (control functions) by one single connection wire to MICROBEAST PLUS. This is done by packing all channel output data to a digital data paket or by chaining the servo signals. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBus, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM<br />

	{{QUOTE\|There are single-line receivers available that supply additional servo outputs. In combination with MICROBEAST PLUS you only have to treat such receivers as single-line receivers if you really use the single-line function. If you connect the receiver by using the standard 5-wire layout as shown above, such receiver has to be considered as "Standard receiver".}}<br />		{{QUOTE\|There are single-line receivers available that supply additional servo outputs. In combination with MICROBEAST PLUS you only have to treat such receivers as single-line receivers if you really use the single-line function. If you connect the receiver by using the standard 5-wire layout as shown above, such receiver has to be considered as "Standard receiver".}}<br />

FuzzyBot: Importing a new version from external source

2020-10-01T08:01:14Z

Importing a new version from external source

← Older revision		Revision as of 08:01, 1 October 2020
Line 10:		Line 10:

	=Standard receiver=		=Standard receiver=
	A conventional receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each ~~servo~~ output to one ~~specific~~ control function ~~at the~~ MICROBEAST PLUS using one connection wire for each function. ~~You have these~~ 5 ~~input~~ functions (wires): Aileron, Elevator, Rudder, Collective pitch and ~~gyro~~ gain. ~~Simply connect~~ each wire to the corresponding ~~channel~~ output ~~port~~ at the receiver which you like to use for the specific function. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to each channel testwise!<br />		A conventional receiver with multiple servo output connectors is what we consider a "Standard receiver". Here you connect each output to one control function of MICROBEAST PLUS by using one connection wire for each function. The 5 control functions (wires) are: Aileron, Elevator, Rudder, Collective pitch and Gyro gain. Connect each wire to the corresponding servo output at the receiver which you like to use for the specific function. If you don't know which stick controls which channel have a look at your radio's servo monitor, refer to your radios instruction manual or simply connect a servo to each channel testwise!<br />
	<br />		<br />
	{\|cellspacing = "20"		{\|cellspacing = "20"
	\|style="text-align:center;"\| [[Image:Standard_RX.png\|250px]]		\|style="text-align:center;"\| [[Image:Standard_RX.png\|250px]]
	\|}<br />		\|}<br />
	Here we show connection layouts for two common radio brands. Note that this is only exemplary, the channel output of your transmitter can by different even when using a radio of this brand. And you can use any ~~other~~ radio system on the market ~~together with MICROBEAST PLUS when using the servo output channels of the receiver~~, not only these two brands!		Here we show connection layouts for two common radio brands. Note that this is only exemplary, the channel output of your transmitter can by different even when using a radio of this brand. And you can use any radio system on the market, not only these two brands!
	{\|cellspacing = "20"		{\|cellspacing = "20"
	\|[[Image:Spektrum_RX.png\|x100px]]		\|[[Image:Spektrum_RX.png\|x100px]]
Line 22:		Line 22:
	{{QUOTE\|		{{QUOTE\|
	* The wires for rudder, pitch and gyro are signal wires. They must be placed on the same receiver side as the the both orange wires from aileron and elevator!		* The wires for rudder, pitch and gyro are signal wires. They must be placed on the same receiver side as the the both orange wires from aileron and elevator!
	* You must connect all 5 functions/wires to the receiver. When you ~~do not~~ connect all wires the system will not finish initialization sequence!		* You must connect all 5 functions/wires to the receiver. When you don't connect all wires, the system will not finish initialization sequence!
	* The throttle servo/speed controller is connected to the receiver's throttle output. Using the ~~Governor~~ function of MICROBEAST PLUS ~~therefore~~ is not possible in combination with a Standard receiver.}}<br />		* The throttle servo/speed controller is connected to the receiver's throttle output. Using the headspeed governor function of MICROBEAST PLUS is not possible in combination with a Standard receiver!}}<br />
	<br />		<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2020-10-01T08:00:28Z

Importing a new version from external source

← Older revision		Revision as of 08:00, 1 October 2020
Line 30:		Line 30:
	With a single-line receiver all channels (control functions) are transmitted by one single connection wire to MICROBEAST PLUS. This is done by packing all channel output data to a data paket or by chaining the servo signals to one output port. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBus, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM<br />		With a single-line receiver all channels (control functions) are transmitted by one single connection wire to MICROBEAST PLUS. This is done by packing all channel output data to a data paket or by chaining the servo signals to one output port. At the moment MICROBEAST PLUS supports the following systems: Multiplex® SRLX, Spektrum® SRXL, Futaba® SBus, JR® X-Bus(B), Jeti® UDI, Jeti® EXBus, ALIGN® iBus, FlySky® iBus, Graupner HOTT® SUMD, SPPM<br />

	{{QUOTE\|There are single-line receivers available that supply additional ~~single channel connectors/~~servo outputs. In combination with MICROBEAST PLUS you only have to treat such receivers as single-line receivers if you really use the single-line function. If you connect the receiver by using the standard 5-~~plug~~ layout, such receiver has to be considered as Standard receiver ~~in the following and as shown above~~.}}<br />		{{QUOTE\|There are single-line receivers available that supply additional servo outputs. In combination with MICROBEAST PLUS you only have to treat such receivers as single-line receivers if you really use the single-line function. If you connect the receiver by using the standard 5-wire layout as shown above, such receiver has to be considered as "Standard receiver".}}<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2020-10-01T07:59:49Z

Importing a new version from external source

← Older revision		Revision as of 07:59, 1 October 2020
Line 5:		Line 5:
	<br />		<br />

	MICROBEAST PLUS can work with a lot of different receiver types and radio brands ~~and~~ especially with different types of radio signal protocols. Depending on which signal protocol and receiver you intend to use the wiring layout may vary. In the following you can see all supported protocols and specific wiring schemes for each receiver type. '''Ensure a tight fit of the connectors.''' The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Anyhow, especially when using a receiver with single wire output it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.<br />		MICROBEAST PLUS can work with a lot of different receiver types and radio brands, especially with different types of radio signal protocols. Depending on which signal protocol and receiver you intend to use, the wiring layout may vary. In the following you can see all supported protocols and specific wiring schemes for each receiver type. '''Ensure a tight fit of the connectors.''' The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Anyhow, especially when using a receiver with single wire output it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.<br />
	<br />		<br />
	<br />		<br />