Manuals:MBPlusFblV52:Receiver M/en - Revision history

FuzzyBot: Updating to match new version of source page

2023-09-19T08:23:43Z

Updating to match new version of source page

← Older revision		Revision as of 08:23, 19 September 2023
Line 106:		Line 106:
	[[File:Hobbywing.png\|x300px\|none]]		[[File:Hobbywing.png\|x300px\|none]]
	<br />		<br />
	{{QUOTE\|* ~~Smaller~~ Hobbywing® Platinum models (Platinum ~~60 and 80~~) do not measure current. Here ~~displayed~~ current and consumed capacity will stay "0.00". However, you can use the displayed battery voltage to estimate the maximum flight time of the model and to effectively prevent a deep discharge of the battery, i. e. by setting a low voltage alarm in your radio.		{{QUOTE\|* There are some Hobbywing® Platinum models (i. e. Platinum "LV" series) that do not measure current. Here current and consumed capacity will stay "0.00". However, you can use the displayed battery voltage to estimate the maximum flight time of the model and to effectively prevent a deep discharge of the battery, i. e. by setting a low voltage alarm in your radio.
	* '''Hobbywing® Platinum V3''' ESC don't supply any telemtry output. Anyhow, you can connect the motor speed cable as shown above to MICROBEAST ~~PLUS~~. Then you can display motor speed/headspeed on your radio at least!}}<br />		* Additionally some ESC do not measure temperature, so Temperature will stay at 0 degrees in your telemetry display. It's no malfunction, there simply is no value available.
			* '''Hobbywing® Platinum V3''' ESC don't supply any telemtry output. Anyhow, you can connect the motor speed cable as shown above to MICROBEAST ULTRA. Then you can display motor speed/headspeed on your radio at least!}}<br />
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2023-08-18T08:00:20Z

Updating to match new version of source page

← Older revision		Revision as of 08:00, 18 August 2023
Line 171:		Line 171:
	\|[[File:sproto_3_.png\|x250px\|none]]		\|[[File:sproto_3_.png\|x250px\|none]]
	\|}<br />		\|}<br />
			<br />
			<br />

			==Spektrum® AVIAN Smart ESC==
			MICROBEAST PLUS allows to use telemetry from a Spektrum® AVIAN ESC with SMART battery feature in combination with any receiver type. Anyhow, when using a Spektrum® transmitter you can get full advantage of the Spektrum® SMART programming feature. Using with another type of radio system, you will only get basic telemetry functions (current, voltage, temperature, consumption, pwm).<br />
			<br />
			Spektrum® AVIAN ESC do not have a separate line for telemetry data. Here motor control and telemetry data is sent bidirectional on the main connection wire. For this we must connect the AVIAN ESC to the [SYS] port of MICROBEAST PLUS, as the other connectors [DI1] and [CH5] can only work in one direction.<br />
			<br />
			Please note that you must activate the [SYS] port connection at menu point '''L''', not at menu point '''M'''.<br />
	<br />		<br />
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2023-08-18T07:43:01Z

Updating to match new version of source page

← Older revision		Revision as of 07:43, 18 August 2023
Line 28:		Line 28:

	=Adjustment on the device=		=Adjustment on the device=
	~~After~~ receiver ~~scan~~ and ~~function assignment the Menu Point~~ '''M''' ~~will open, in case you're using a Spektrum® SRXL2 or JETI® EXBUS radio system~~. If needed you can directly ~~get~~ to ~~this screen~~ without ~~changing your basic radio setup~~ by ~~clicking~~ the button ~~"Telemetry" in overview screen of RECEIVER MENU~~.<br />		In case you're using a receiver with telemetry capability, you can change the telemetry parameters at menu points '''L''' and '''M'''. If needed, you can directly skip to these parameters without scanning receiver type and assigning functions at RECEIVER MENU points '''A''' and '''B''' by pushing and holding the button for at least 2 seconds at menu points '''A''' or '''B'''.<br />
	<br />		<br />
	To select the connected ESC/telemetry data source move the rudder stick repeatedly in one direction until the Status LED lights in the correct color:<br />
			'''Telemetry device at [SYS] port'''<br />
			At menu point '''L''' you can choose the type of telemetry device connected at [SYS] port. To select the device, move the rudder stick repeatedly in one direction until the Status LED lights in the correct color:<br />
			<br />
			{\|- cellpadding="4" cellspacing="0" border="1"
			\|- style="width:100px; text-align:left;"
			! Status-LED !! Telemetry device
			\|-
			\|style="color:white; background-color:#000000" \| off
			\| No device at [SYS] port
			\|-
			\|style="color:white; background-color:#FF3300" \| red
			\| Spektrum® AVIAN ESC
			\|-
			\|style="color:white; background-color:#0066FF" \| blue
			\| Graupner® HOTT telemetry input
			\|}<br />
			<br />

			'''Telemetry input source at [IO2] port'''<br />
			At menu point '''M''' you can choose the type of ESC/signal source that is connected at [IO2] port. To select the ESC/telemetry data source, move the rudder stick repeatedly in one direction until the Status LED lights in the correct color:<br />
	<br />		<br />
	{\|- cellpadding="4" cellspacing="0" border="1"		{\|- cellpadding="4" cellspacing="0" border="1"
Line 59:		Line 79:
	<br />		<br />

	~~Please note there~~ are some additional settings for telemetry available:<br />		{{WARNING_QUOTE\|When using an ESC with telemetry at [IO2] port, the '''control line of the speed controller must be connected to pin [IO1]!''' }}<br />
			<br />

			'''There are some additional settings for telemetry available:'''<br />
	* In GOVERNOR MENU you can use the '''signal divider''' and '''gear ratio''' adjustment to calculate the rotor head speed from the incoming motor speed. Most ESCs will send the electrical motor speed on the telemetry channel only, so you must divide the motor speed by the number of magnet pole pairs and by the main gear ratio of your helicopter, in order to display the rotor speed. See [[Manuals:MBPlusFblV52:Governormenu_E/en\|GOVERNOR MENU E]] and [[Manuals:MBPlusFblV52:Governormenu_E/en\|GOVERNOR MENU F]] for more details.		* In GOVERNOR MENU you can use the '''signal divider''' and '''gear ratio''' adjustment to calculate the rotor head speed from the incoming motor speed. Most ESCs will send the electrical motor speed on the telemetry channel only, so you must divide the motor speed by the number of magnet pole pairs and by the main gear ratio of your helicopter, in order to display the rotor speed. See [[Manuals:MBPlusFblV52:Governormenu_E/en\|GOVERNOR MENU E]] and [[Manuals:MBPlusFblV52:Governormenu_E/en\|GOVERNOR MENU F]] for more details.
	* Some ESC do not calculate the current consumption (Hobbywing®, Kontronik® Jive). Here MICROBEAST PLUS will do the work and calculate the current consumption using the instant current values. Anyhow, results may vary as speed controllers usually measure the motor current but not the battery current. So we added the parameter '''Capacity correction''' which allows to compensate the offset. I.e. when telemetry shows 3600mAh of current consumption, but in reality you did charge 4000mAh back into your battery after the flight, you can increase the Current correction by 10% to 110 in order to get proper reading the next time. Please note this very special value can only be set by using StudioX!<br />		* Some ESC do not calculate the current consumption (Hobbywing®, Kontronik® Jive). Here MICROBEAST PLUS will do the work and calculate the current consumption using the instant current values. Anyhow, results may vary as speed controllers usually measure the motor current but not the battery current. So we added the parameter '''Capacity correction''' which allows to compensate the offset. I.e. when telemetry shows 3600mAh of current consumption, but in reality you did charge 4000mAh back into your battery after the flight, you can increase the Current correction by 10% to 110 in order to get proper reading the next time. Please note this very special value can only be set by using StudioX!<br />
Line 65:		Line 88:

	=Setup with StudioX=		=Setup with StudioX=
	After receiver scan and function assignment an additional setup screen for telemetry will open, in case you're using a ~~Spektrum® SRXL2 or JETI® EXBUS radio system~~. If needed, also you can directly ~~get to this screen~~ without changing your basic radio setup by clicking the ~~button "Telemetry"~~ in overview screen of RECEIVER MENU.<br />		After receiver scan and function assignment an additional setup screen for telemetry will open, in case you're using a receiver with telemetry capability. If needed, also you can directly access the telemetry options without changing your basic radio setup by clicking the buttons in overview screen of RECEIVER MENU.<br />
	<br />		<br />
	* Choose the connected ESC/telemetry data source by pressing the corresponding button.<br />		* Choose the connected ESC/telemetry data source by pressing the corresponding button.<br />
Line 72:		Line 95:
	<br />		<br />

	=~~Connecting the telemetry sensor/~~ESC=		=ESC connections=
	~~<br />~~
	{{WARNING_QUOTE\|When using telemetry, the '''control line of the speed controller must be connected to pin [DI1], not [CH5]!''' The cable for the telemetry signal is plugged into [CH5] instead.}}<br />
	~~<br />~~
	<br />		<br />

Line 131:		Line 151:
	Connect the control wire of your OMP ESC to port [DI1]. Connect the pin labeled with "TX" from the ESC to the port [CH5] using a single servo wire with plugs on both sides. Optionaly you can connect the yellow wire for measuring the motor speed to the [RPM] input at MICROBEAST PLUS, so that it is out of the way. For telemetry transmission it is not needed as the data will be included in the telemetry signal!<br />		Connect the control wire of your OMP ESC to port [DI1]. Connect the pin labeled with "TX" from the ESC to the port [CH5] using a single servo wire with plugs on both sides. Optionaly you can connect the yellow wire for measuring the motor speed to the [RPM] input at MICROBEAST PLUS, so that it is out of the way. For telemetry transmission it is not needed as the data will be included in the telemetry signal!<br />
	<br />		<br />
	Make sure the ESC is sending data with OMP telemetry data protocol. This is the factory setting of the ESC. Do not change the protocol to "SBUS2" or other! MICROBEAST PLUS will convert the data into your radio's protocol as needed.		Make sure the ESC is sending data with OMP telemetry data protocol. This is the factory setting of the ESC. Do not change the protocol to "SBUS2" or other! MICROBEAST PLUS will convert the data into your radio's protocol as needed.<br />
	<br />		<br />
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2023-08-18T07:24:19Z

Updating to match new version of source page

← Older revision		Revision as of 07:24, 18 August 2023
Line 12:		Line 12:
	* Kontronik® JIVE Pro/Kosmik		* Kontronik® JIVE Pro/Kosmik
	* YGE® ESC with Texy protocol		* YGE® ESC with Texy protocol
			* OMP 65A ESC that is included with OMP M4 heli
	* Scorpion® Tribunus II ("UnSc" mode)		* Scorpion® Tribunus II ("UnSc" mode)
	* Spektrum Avian ESC (connected at [SYS] port)		* Spektrum Avian ESC (connected at [SYS] port)
Line 42:		Line 43:
	\|-		\|-
	\|style="color:white; background-color:#CC66CC" \| purple		\|style="color:white; background-color:#CC66CC" \| purple
	\| Hobbywing® Platinum V5		\| Hobbywing® Platinum V5 / OMP 65A ESC
	\|-		\|-
	\|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" \| red flashing		\|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" \| red flashing
Line 80:		Line 81:
	Connect the control wire of your Hobbywing® ESC to port [DI1]. Connect the programming port of your Hobbywing® ESC to port [CH5] using a standard servo wire with male servo plugs on each end.<br />		Connect the control wire of your Hobbywing® ESC to port [DI1]. Connect the programming port of your Hobbywing® ESC to port [CH5] using a standard servo wire with male servo plugs on each end.<br />
	<br />		<br />
	If needed you can connect the yellow wire for measuring the motor speed to the RPM input at MICROBEAST PLUS. The motor speed signal can be used for the internal governor function of MICROBEAST PLUS. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />		If needed you can connect the yellow wire for measuring the motor speed to the [RPM] input at MICROBEAST PLUS. The motor speed signal can be used for the internal governor function of MICROBEAST PLUS. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />
	<br />		<br />

Line 124:		Line 125:
	<br />		<br />
	{{WARNING_QUOTE\|Please be very careful when connecting your ESC with MICROBEAST PLUS. The voltage pins of [CH5] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST PLUS or your ESC if not following these instructions properly!}}<br />		{{WARNING_QUOTE\|Please be very careful when connecting your ESC with MICROBEAST PLUS. The voltage pins of [CH5] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST PLUS or your ESC if not following these instructions properly!}}<br />
			<br />
			<br />

			==OMP 65A ESC==
			Connect the control wire of your OMP ESC to port [DI1]. Connect the pin labeled with "TX" from the ESC to the port [CH5] using a single servo wire with plugs on both sides. Optionaly you can connect the yellow wire for measuring the motor speed to the [RPM] input at MICROBEAST PLUS, so that it is out of the way. For telemetry transmission it is not needed as the data will be included in the telemetry signal!<br />
			<br />
			Make sure the ESC is sending data with OMP telemetry data protocol. This is the factory setting of the ESC. Do not change the protocol to "SBUS2" or other! MICROBEAST PLUS will convert the data into your radio's protocol as needed.
	<br />		<br />
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2023-04-14T12:35:07Z

Updating to match new version of source page

← Older revision		Revision as of 12:35, 14 April 2023
Line 11:		Line 11:
	* Kontronik® JIVE/PowerJIVE/HeliJIVE		* Kontronik® JIVE/PowerJIVE/HeliJIVE
	* Kontronik® JIVE Pro/Kosmik		* Kontronik® JIVE Pro/Kosmik
			* YGE® ESC with Texy protocol
	* Scorpion® Tribunus II ("UnSc" mode)		* Scorpion® Tribunus II ("UnSc" mode)
	* Spektrum Avian ESC (connected at [SYS] port)		* Spektrum Avian ESC (connected at [SYS] port)
Line 48:		Line 49:
	\|style="color:white; background-color:#FF3300" \| red		\|style="color:white; background-color:#FF3300" \| red
	\| Kontronik® JIVE Pro/Kosmik		\| Kontronik® JIVE Pro/Kosmik
			\|-
			\|style="color:white; background: linear-gradient(to right, #0066FF, black, #0066FF)" \| blue flashing
			\| YGE® Texy
	\|-		\|-
	\|style="color:white; background-color:#0066FF" \| blue		\|style="color:white; background-color:#0066FF" \| blue

FuzzyBot: Updating to match new version of source page

2023-03-08T11:32:12Z

Updating to match new version of source page

← Older revision		Revision as of 11:32, 8 March 2023
Line 1:		Line 1:
	{{DISPLAYTITLE:Receiver Menu - Telemetry\|noerror}}		{{DISPLAYTITLE:Receiver Menu - Telemetry\|noerror}}
	{{~~TOC_MBUltraFblV5~~\|Manuals:~~MBUltraFblV5~~:~~Setupmenu_B~~/en\|Manuals:~~MBUltraFblV5~~:~~Setupmenu_D~~/en\|~~SETUPMENU~~\|}}		{{TOC_MBPlusV5\|Manuals:MBPlusFblV52:Receiver_B/en\|Manuals:MBPlusFblV52:Receiver_N/en\|RECEIVERMENU\|2}}
	__TOC__		__TOC__
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2023-03-08T11:31:13Z

Updating to match new version of source page

← Older revision		Revision as of 11:31, 8 March 2023
Line 1:		Line 1:
	{{DISPLAYTITLE:Receiver Menu - Telemetry\|noerror}}		{{DISPLAYTITLE:Receiver Menu - Telemetry\|noerror}}
	{{~~TOC_MBPlusV5~~\|Manuals:~~MBPlusFblV52~~:~~Receiver_B~~/en\|Manuals:~~MBPlusFblV52~~:~~Receiver_N~~/en\|~~RECEIVERMENU~~\|2}}		{{TOC_MBUltraFblV5\|Manuals:MBUltraFblV5:Setupmenu_B/en\|Manuals:MBUltraFblV5:Setupmenu_D/en\|SETUPMENU\|}}
	__TOC__		__TOC__
	<br />		<br />
Line 12:		Line 12:
	* Kontronik® JIVE Pro/Kosmik		* Kontronik® JIVE Pro/Kosmik
	* Scorpion® Tribunus II ("UnSc" mode)		* Scorpion® Tribunus II ("UnSc" mode)
	* ~~speed~~ sensor connected at RPM input<br />		* Spektrum Avian ESC (connected at [SYS] port)
			* Speed sensor connected at RPM input<br />
	<br />		<br />

Line 18:		Line 19:
	* Jeti® EXBUS		* Jeti® EXBUS
	* Spektrum® SRXL2		* Spektrum® SRXL2
			* Graupner HOTT (connected at [SYS] port)
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2023-01-09T07:57:58Z

Updating to match new version of source page

← Older revision		Revision as of 07:57, 9 January 2023
Line 105:		Line 105:
	The Kontronik® JIVE PRO/Kosmik controllers comes with a 5-pin connector that is normally used to program the motor controller by the use of a jumper wire. Since firmware version 1.10 (JIVE Pro)/4.12 (KOSMIK) Kontronik® added a generic telemetry data output to this connection. Please make sure your JIVE PRO/KOSMIK is updated to the latest version. On first generation KOSMIK series ESCs the telemetry port is the socket in the middle. On newer KOSMIK (Cool) ESCs you can choose, which port to use by software. Here select the generic Kontronik® telemtry protocol.<br />		The Kontronik® JIVE PRO/Kosmik controllers comes with a 5-pin connector that is normally used to program the motor controller by the use of a jumper wire. Since firmware version 1.10 (JIVE Pro)/4.12 (KOSMIK) Kontronik® added a generic telemetry data output to this connection. Please make sure your JIVE PRO/KOSMIK is updated to the latest version. On first generation KOSMIK series ESCs the telemetry port is the socket in the middle. On newer KOSMIK (Cool) ESCs you can choose, which port to use by software. Here select the generic Kontronik® telemtry protocol.<br />
	<br />		<br />
	To connect MICROBEAST PLUS with your JIVE PRO/KOSMIK ESC you need a special type of wire. As shown below, the telemetry signal pin is the middle pin of the 5-pin connector. The most inner pin is common ground on JIVE Pro ESCs. On KOSMIK the pin next to the "LED side" is common ground. It is highly recommended to use a multimeter and check polarity before connecting your ESC to MICROBEAST PLUS. Note that the pin on the opposite side carries +5V. Do not connect anything here!<br />		To connect MICROBEAST PLUS with your JIVE PRO/KOSMIK ESC you need a special type of wire. You can get a ready to use solution from Kontronik® - Ordernr. 9703 (TELEMETRY CABLE JR). As shown below, the telemetry signal pin is the middle pin of the 5-pin connector. The most inner pin is common ground on JIVE Pro ESCs. On KOSMIK the pin next to the "LED side" is common ground. It is highly recommended to use a multimeter and check polarity before connecting your ESC to MICROBEAST PLUS. Note that the pin on the opposite side carries +5V. Do not connect anything here!<br />
	<br />		<br />
	On MICROBEAST PLUS side you must connect the signal wire to the upper pin of port [CH5] and the common ground to the lowest pin (=minus). '''You mustn't connect anything to the middle pin (=voltage) of port [CH5]!'''<br />		On MICROBEAST PLUS side you must connect the signal wire to the upper pin of port [CH5] and the common ground to the lowest pin (=minus). '''You mustn't connect anything to the middle pin (=voltage) of port [CH5]!'''<br />

FuzzyBot: Updating to match new version of source page

2023-01-09T07:45:28Z

Updating to match new version of source page

← Older revision		Revision as of 07:45, 9 January 2023
Line 11:		Line 11:
	* Kontronik® JIVE/PowerJIVE/HeliJIVE		* Kontronik® JIVE/PowerJIVE/HeliJIVE
	* Kontronik® JIVE Pro/Kosmik		* Kontronik® JIVE Pro/Kosmik
	* Scorpion® Tribunus ("UnSc" mode)		* Scorpion® Tribunus II ("UnSc" mode)
	* speed sensor connected at RPM input<br />		* speed sensor connected at RPM input<br />
	<br />		<br />
Line 103:		Line 103:

	==Kontronik JIVE PRO/KOSMIK==		==Kontronik JIVE PRO/KOSMIK==
	The Kontronik® JIVE PRO/Kosmik controllers comes with a 5-pin connector that is normally used to program the motor controller by the use of a jumper wire. Since firmware version 1.10 Kontronik® added a generic telemetry data output to this connection. Please make sure your JIVE PRO/~~Kosmik~~ is updated to the latest version.<br />		The Kontronik® JIVE PRO/Kosmik controllers comes with a 5-pin connector that is normally used to program the motor controller by the use of a jumper wire. Since firmware version 1.10 (JIVE Pro)/4.12 (KOSMIK) Kontronik® added a generic telemetry data output to this connection. Please make sure your JIVE PRO/KOSMIK is updated to the latest version. On first generation KOSMIK series ESCs the telemetry port is the socket in the middle. On newer KOSMIK (Cool) ESCs you can choose, which port to use by software. Here select the generic Kontronik® telemtry protocol.<br />
	<br />		<br />
	To connect MICROBEAST PLUS with your JIVE PRO/~~Kosmik~~ ESC you need a special type of wire. As shown below, the telemetry signal pin is the middle pin of the 5-pin connector. The most inner pin is common ground. On MICROBEAST PLUS side you must connect the signal wire to the upper pin of port [CH5] and the common ground to the lowest pin (=minus). '''You mustn't connect anything to the middle pin (=voltage) of port [CH5]!'''<br />		To connect MICROBEAST PLUS with your JIVE PRO/KOSMIK ESC you need a special type of wire. As shown below, the telemetry signal pin is the middle pin of the 5-pin connector. The most inner pin is common ground on JIVE Pro ESCs. On KOSMIK the pin next to the "LED side" is common ground. It is highly recommended to use a multimeter and check polarity before connecting your ESC to MICROBEAST PLUS. Note that the pin on the opposite side carries +5V. Do not connect anything here!<br />
			<br />
			On MICROBEAST PLUS side you must connect the signal wire to the upper pin of port [CH5] and the common ground to the lowest pin (=minus). '''You mustn't connect anything to the middle pin (=voltage) of port [CH5]!'''<br />
	<br />		<br />
	Connect the control wire (MASTER port) of your KONTRONIK® ESC to port [DI1]. If needed you can connect the additional power output (SLAVE port) to the [SYS] port of MICROBEAST PLUS.<br />		Connect the control wire (MASTER port) of your KONTRONIK® ESC to port [DI1]. If needed you can connect the additional power output (SLAVE port) to the [SYS] port of MICROBEAST PLUS.<br />
Line 115:		Line 117:
	\|}<br />		\|}<br />
	<br />		<br />
	{{WARNING_QUOTE\|Please be very careful when connecting your ESC with MICROBEAST PLUS. The voltage pins of [CH5] mustn't be connected with the telemetry port of your JIVE PRO/~~Kosmik~~ ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST PLUS or your ESC if not following these instructions properly!}}<br />		{{WARNING_QUOTE\|Please be very careful when connecting your ESC with MICROBEAST PLUS. The voltage pins of [CH5] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST PLUS or your ESC if not following these instructions properly!}}<br />
	<br />		<br />
	<br />		<br />

	==Scorpion® Tribunus==		==Scorpion® Tribunus II==
	Connect the control wire (MASTER) of your Scorpion® ESC to port [DI1]. Connect the programming port (PC) of your Scorpion® ESC to port [CH5] using a standard servo wire with male servo plugs on each end.<br />		Connect the control wire (MASTER) of your Scorpion® ESC to port [DI1]. Connect the programming port (PC) of your Scorpion® ESC to port [CH5] using a standard servo wire with male servo plugs on each end.<br />
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2022-07-10T18:15:34Z

Updating to match new version of source page

← Older revision		Revision as of 18:15, 10 July 2022
Line 34:		Line 34:
	\|style="color:white; background-color:#000000" \| off		\|style="color:white; background-color:#000000" \| off
	\| no telemetry/use RPM signal		\| no telemetry/use RPM signal
			\|-
			\|style="color:white; background: linear-gradient(to right, #CC66CC, black, #CC66CC) \| purple flashing
			\| Hobbywing® Platinum V4
	\|-		\|-
	\|style="color:white; background-color:#CC66CC" \| purple		\|style="color:white; background-color:#CC66CC" \| purple
	\| Hobbywing® Platinum ~~(V4/~~V5)		\| Hobbywing® Platinum V5
	\|-		\|-
	\|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" \| red flashing		\|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" \| red flashing