Manuals:MBPlusFblV52:Receiver N - Revision history

Shornstein: Marked this version for translation

2023-03-09T10:13:49Z

Marked this version for translation

← Older revision		Revision as of 10:13, 9 March 2023
Line 6:		Line 6:
	<br />		<br />

			<!--T:4-->
	At Menu Point N of the RECEIVER MENU you teach the failsafe position for throttle channel. In case the receiver signal is interrupted during operation the throttle servo/speed controller connected to the [CH5] output is automatically moved to this position. This particularly is the case:		At Menu Point N of the RECEIVER MENU you teach the failsafe position for throttle channel. In case the receiver signal is interrupted during operation the throttle servo/speed controller connected to the [CH5] output is automatically moved to this position. This particularly is the case:
	* if using a single-line receiver that turns off the signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® HOTT receiver in „SUMDOF“ mode)		* if using a single-line receiver that turns off the signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® HOTT receiver in „SUMDOF“ mode)

Shornstein at 10:13, 9 March 2023

2023-03-09T10:13:34Z

← Older revision		Revision as of 10:13, 9 March 2023
Line 6:		Line 6:
	<br />		<br />

	~~=Adjustment on the device= <!--T:2-->~~		At Menu Point N of the RECEIVER MENU you teach the failsafe position for throttle channel. In case the receiver signal is interrupted during operation the throttle servo/speed controller connected to the [CH5] output is automatically moved to this position. This particularly is the case:
	At Menu Point N of the RECEIVER MENU you teach the failsafe position for throttle channel. In case the receiver signal is interrupted during operation the throttle servo/speed controller connected to the [CH5] ~~Output~~ is automatically moved to this position. This particularly is the case:
	* if using a single-line receiver that turns off the signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® HOTT receiver in „SUMDOF“ mode)		* if using a single-line receiver that turns off the signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® HOTT receiver in „SUMDOF“ mode)
	* if the connection between MICROBEAST PLUS and receiver gets disconnected physically		* if the connection between MICROBEAST PLUS and receiver gets disconnected physically
Line 15:		Line 14:
	'''Note:'''		'''Note:'''
	* The fail-safe function is not effective if the receiver continues sending data even if the radio link is interrupted. In this case the failsafe setting of the remote control system may take precedence.		* The fail-safe function is not effective if the receiver continues sending data even if the radio link is interrupted. In this case the failsafe setting of the remote control system may take precedence.
	* To avoid accidents, you should program electric motors to “off“ and reduce throttle on nitro helicopters to idle. The other control functions will be set to „position hold“ in case of signal interruption. For these setting a failsafe position is not provided.<br />		* To avoid accidents, you should program electric motors to “off“ and reduce throttle on nitro helicopters to idle.
			* The other control functions will be set to „position hold“ in case of signal interruption. For these setting a failsafe position is not provided.<br />
	<br />		<br />

			=Adjustment on the device= <!--T:2-->
	To teach the failsafe position simply set the throttle channel on your remote control to the desired position and press the button briefly. '''If you did not connect a function to CH5 Output and don't need throttle failsafe, press the button to complete setup anyway!'''<br />		To teach the failsafe position simply set the throttle channel on your remote control to the desired position and press the button briefly. '''If you did not connect a function to CH5 Output and don't need throttle failsafe, press the button to complete setup anyway!'''<br />
	<br />		<br />
	[[File:Failsafe_setup.png\|noframe\|none\|x180px]]<br />		[[File:Failsafe_setup.png\|noframe\|none\|x180px]]<br />
	<br />		<br />
	{{WARNING_QUOTE\|'''During failsafe setting the CH5 ~~Output~~ is enabled and can be controlled by the transmitter channel that is assigned to throttle function.''' This allows to check your throttle position in reality. When using electric models make sure the motor is disconnected from the ESC or the pinion is removed from the motor, so that it will not drive the model by accident.		{{WARNING_QUOTE\|'''During failsafe setting the [CH5] output is enabled and can be controlled by the transmitter channel that is assigned to throttle function.''' This allows to check your throttle position in reality. When using electric models make sure the motor is disconnected from the ESC or the pinion is removed from the motor, so that it will not drive the model by accident.
	}}<br />		}}<br />
	<br />		<br />
	<br />		<br />

	=Setup with StudioX= <!--T:3-->		=Setup with StudioX app= <!--T:3-->
	After you've set the control functions you will be asked to program the failsafe position for the throttle channel. In case the single-line signal is interrupted during operation, the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:
	* if using a single-line receiver that turns of the single-line signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® receiver in „SUMDOF“ mode)
	* if the connection between MICROBEAST PLUS and receiver gets disconnected
	* during initialization when the transmitter was not switched on before or was switched on too late and the radio link between transmitter and receiver is not established yet
	Additionally the failsafe position is used by the internal Governor function in case you're using a helicopter with electric drive system. Here the throttle is moved to the stored failsafe position when you set the Governor to Autorotation bailout mode!<br />
	~~<br />~~
	~~'''Note:'''~~
	* The fail-safe function is not effective if the receiver continues sending data even if the radio link is interrupted. In this case the failsafe setting of the remote control system may take precedence.
	* To avoid accidents, you should program electric motors to “off“ and reduce throttle on nitro helicopters to idle. The other control functions will be set to „position hold“ in case of signal interruption. For these setting a failsafe position is not provided.<br />
	~~<br /~~>
	To teach the failsafe position choose "Proceed" when asked to teach the failsafe position and set the throttle channel on your remote control to the desired position. Then press '''Set''' to save the position. If you did not connect a function to CH5 Output and don't need throttle failsafe, press '''Cancel''' to complete setup!<br />		To teach the failsafe position choose "Proceed" when asked to teach the failsafe position and set the throttle channel on your remote control to the desired position. Then press '''Set''' to save the position. If you did not connect a function to CH5 Output and don't need throttle failsafe, press '''Cancel''' to complete setup!<br />
	<br />		<br />
Line 53:		Line 45:
	<br />		<br />
	<br />		<br />
	{{WARNING_QUOTE\|'''During failsafe setting the CH5 ~~Output~~ is enabled and can be controlled by the transmitter channel that is assigned to throttle function.''' This allows to check your throttle position in reality. When using electric models make sure the motor is disconnected from the ESC or the pinion is removed from the motor, so that it will not drive the model by accident.		{{WARNING_QUOTE\|'''During failsafe setting the [CH5] output is enabled and can be controlled by the transmitter channel that is assigned to throttle function.''' This allows to check your throttle position in reality. When using electric models make sure the motor is disconnected from the ESC or the pinion is removed from the motor, so that it will not drive the model by accident.
	}}<br />		}}<br />
	<br />		<br />
	<br />		<br />
	</translate>		</translate>

Shornstein at 10:01, 9 March 2023

2023-03-09T10:01:29Z

← Older revision		Revision as of 10:01, 9 March 2023
Line 8:		Line 8:
	=Adjustment on the device= <!--T:2-->		=Adjustment on the device= <!--T:2-->
	At Menu Point N of the RECEIVER MENU you teach the failsafe position for throttle channel. In case the receiver signal is interrupted during operation the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:		At Menu Point N of the RECEIVER MENU you teach the failsafe position for throttle channel. In case the receiver signal is interrupted during operation the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:
	* if using a single-line receiver that turns of the ~~single-line~~ signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® receiver in „SUMDOF“ mode)		* if using a single-line receiver that turns off the signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® HOTT receiver in „SUMDOF“ mode)
	* if the connection between MICROBEAST PLUS and receiver gets disconnected		* if the connection between MICROBEAST PLUS and receiver gets disconnected physically
	* during initialization when the transmitter ~~was~~ not switched on ~~before~~ or was switched on too late and the radio link between transmitter and receiver is not established yet		* during initialization phase when the transmitter is not switched on or was switched on too late and the radio link between transmitter and receiver is not established yet
	Additionally the failsafe position is used by the ~~internal~~ Governor function in case you're using a helicopter with electric drive system. Here the throttle is moved to the stored failsafe position when you ~~set~~ the Governor to Autorotation ~~bailout~~ mode!<br />		Additionally the failsafe position is used by the Governor function in case you're using a helicopter with electric drive system. Here the throttle is moved to the stored failsafe position when you switch the Governor into Autorotation mode!<br />
	<br />		<br />
	'''Note:'''		'''Note:'''

Shornstein at 20:14, 8 April 2022

2022-04-08T20:14:15Z

← Older revision		Revision as of 20:14, 8 April 2022
Line 2:		Line 2:
	<!--T:1-->		<!--T:1-->
	{{DISPLAYTITLE:Receiver Menu - Throttle failsafe\|noerror}}		{{DISPLAYTITLE:Receiver Menu - Throttle failsafe\|noerror}}
	{{TOC_MBPlusV5\|Manuals:MBPlusFblV52:Receiver_M/en\|Manuals:MBPlusFblV52:Setupmenu_intro/en\|\|2}}		{{TOC_MBPlusV5\|Manuals:MBPlusFblV52:Receiver_M/en\|Manuals:MBPlusFblV52:Setupmenu_intro/en\|RECEIVERMENU\|2}}
	__TOC__		__TOC__
	<br />		<br />

Shornstein: Marked this version for translation

2022-04-07T21:36:27Z

Marked this version for translation

← Older revision		Revision as of 21:36, 7 April 2022
Line 1:		Line 1:
	<translate>		<translate>
			<!--T:1-->
	{{DISPLAYTITLE:Receiver Menu - Throttle failsafe\|noerror}}		{{DISPLAYTITLE:Receiver Menu - Throttle failsafe\|noerror}}
	{{TOC_MBPlusV5\|Manuals:MBPlusFblV52:Receiver_M/en\|Manuals:MBPlusFblV52:Setupmenu_intro/en\|\|2}}		{{TOC_MBPlusV5\|Manuals:MBPlusFblV52:Receiver_M/en\|Manuals:MBPlusFblV52:Setupmenu_intro/en\|\|2}}
Line 5:		Line 6:
	<br />		<br />

	=Adjustment on the device=		=Adjustment on the device= <!--T:2-->
	At Menu Point N of the RECEIVER MENU you teach the failsafe position for throttle channel. In case the receiver signal is interrupted during operation the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:		At Menu Point N of the RECEIVER MENU you teach the failsafe position for throttle channel. In case the receiver signal is interrupted during operation the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:
	* if using a single-line receiver that turns of the single-line signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® receiver in „SUMDOF“ mode)		* if using a single-line receiver that turns of the single-line signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® receiver in „SUMDOF“ mode)
Line 25:		Line 26:
	<br />		<br />

	=Setup with StudioX=		=Setup with StudioX= <!--T:3-->
	After you've set the control functions you will be asked to program the failsafe position for the throttle channel. In case the single-line signal is interrupted during operation, the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:		After you've set the control functions you will be asked to program the failsafe position for the throttle channel. In case the single-line signal is interrupted during operation, the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:
	* if using a single-line receiver that turns of the single-line signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® receiver in „SUMDOF“ mode)		* if using a single-line receiver that turns of the single-line signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® receiver in „SUMDOF“ mode)

Shornstein: Created page with " {{DISPLAYTITLE:Receiver Menu - Throttle failsafe|noerror}} {{TOC_MBPlusV5|Manuals:MBPlusFblV52:Receiver_M/en|Manuals:MBPlusFblV52:Setupmenu_intro/en||2}} TOC <..."

2022-04-07T21:36:18Z

Created page with "<translate> {{DISPLAYTITLE:Receiver Menu - Throttle failsafe|noerror}} {{TOC_MBPlusV5|Manuals:MBPlusFblV52:Receiver_M/en|Manuals:MBPlusFblV52:Setupmenu_intro/en||2}} __TOC__ <..."

New page

<translate>
{{DISPLAYTITLE:Receiver Menu - Throttle failsafe|noerror}}
{{TOC_MBPlusV5|Manuals:MBPlusFblV52:Receiver_M/en|Manuals:MBPlusFblV52:Setupmenu_intro/en||2}}
__TOC__
<br />

=Adjustment on the device=
At Menu Point N of the RECEIVER MENU you teach the failsafe position for throttle channel. In case the receiver signal is interrupted during operation the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:
* if using a single-line receiver that turns of the single-line signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® receiver in „SUMDOF“ mode)
* if the connection between MICROBEAST PLUS and receiver gets disconnected
* during initialization when the transmitter was not switched on before or was switched on too late and the radio link between transmitter and receiver is not established yet
Additionally the failsafe position is used by the internal Governor function in case you're using a helicopter with electric drive system. Here the throttle is moved to the stored failsafe position when you set the Governor to Autorotation bailout mode!<br />
<br />
'''Note:'''
* The fail-safe function is not effective if the receiver continues sending data even if the radio link is interrupted. In this case the failsafe setting of the remote control system may take precedence.
* To avoid accidents, you should program electric motors to “off“ and reduce throttle on nitro helicopters to idle. The other control functions will be set to „position hold“ in case of signal interruption. For these setting a failsafe position is not provided.<br />
<br />
To teach the failsafe position simply set the throttle channel on your remote control to the desired position and press the button briefly. '''If you did not connect a function to CH5 Output and don't need throttle failsafe, press the button to complete setup anyway!'''<br />
<br />
[[File:Failsafe_setup.png|noframe|none|x180px]]<br />
<br />
{{WARNING_QUOTE|'''During failsafe setting the CH5 Output is enabled and can be controlled by the transmitter channel that is assigned to throttle function.''' This allows to check your throttle position in reality. When using electric models make sure the motor is disconnected from the ESC or the pinion is removed from the motor, so that it will not drive the model by accident.
}}<br />
<br />
<br />

=Setup with StudioX=
After you've set the control functions you will be asked to program the failsafe position for the throttle channel. In case the single-line signal is interrupted during operation, the throttle servo/speed controller connected to the [CH5] Output is automatically moved to this position. This particularly is the case:
* if using a single-line receiver that turns of the single-line signal in case of signal loss between receiver and transmitter (e.g. Spektrum® satellite receiver or Graupner® receiver in „SUMDOF“ mode)
* if the connection between MICROBEAST PLUS and receiver gets disconnected
* during initialization when the transmitter was not switched on before or was switched on too late and the radio link between transmitter and receiver is not established yet
Additionally the failsafe position is used by the internal Governor function in case you're using a helicopter with electric drive system. Here the throttle is moved to the stored failsafe position when you set the Governor to Autorotation bailout mode!<br />
<br />
'''Note:'''
* The fail-safe function is not effective if the receiver continues sending data even if the radio link is interrupted. In this case the failsafe setting of the remote control system may take precedence.
* To avoid accidents, you should program electric motors to “off“ and reduce throttle on nitro helicopters to idle. The other control functions will be set to „position hold“ in case of signal interruption. For these setting a failsafe position is not provided.<br />
<br />
To teach the failsafe position choose "Proceed" when asked to teach the failsafe position and set the throttle channel on your remote control to the desired position. Then press '''Set''' to save the position. If you did not connect a function to CH5 Output and don't need throttle failsafe, press '''Cancel''' to complete setup!<br />
<br />
<div class="iosgallery">
<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20025.PNG">
<div class="iostext">After function assignment click <b>Proceed</b> to start teaching the throttle failsafe position</div>
</div>
<div class="iosgallery">
<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20027.PNG">
<div class="iostext">Move throttle to lowest position at which the motor is turned off</div>
</div>
<div class="iosgallery">
<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20028.PNG">
<div class="iostext">Click <b>Set</b> to store the setting</div>
</div>
<br />
<br />
{{WARNING_QUOTE|'''During failsafe setting the CH5 Output is enabled and can be controlled by the transmitter channel that is assigned to throttle function.''' This allows to check your throttle position in reality. When using electric models make sure the motor is disconnected from the ESC or the pinion is removed from the motor, so that it will not drive the model by accident.
}}<br />
<br />
<br />
</translate>

Manuals:MBPlusFblV52:Receiver N - Revision history

Shornstein: Marked this version for translation

Shornstein at 10:13, 9 March 2023

Shornstein at 10:01, 9 March 2023

Shornstein at 20:14, 8 April 2022

Shornstein: Marked this version for translation

Shornstein: Created page with " {{DISPLAYTITLE:Receiver Menu - Throttle failsafe|noerror}} {{TOC_MBPlusV5|Manuals:MBPlusFblV52:Receiver_M/en|Manuals:MBPlusFblV52:Setupmenu_intro/en||2}} __TOC__ <..."

Shornstein: Created page with " {{DISPLAYTITLE:Receiver Menu - Throttle failsafe|noerror}} {{TOC_MBPlusV5|Manuals:MBPlusFblV52:Receiver_M/en|Manuals:MBPlusFblV52:Setupmenu_intro/en||2}} TOC <..."