Manuals:MBUltraFblV5:Receiver A/en - Revision history

FuzzyBot: Updating to match new version of source page

2023-03-09T13:12:42Z

Updating to match new version of source page

← Older revision		Revision as of 13:12, 9 March 2023
Line 1:		Line 1:
	{{DISPLAYTITLE:Receiver Menu - Type selection\|noerror}}		{{DISPLAYTITLE:Receiver Menu - Type selection\|noerror}}
	{{TOC_MBUltraFblV5\|Manuals:MBUltraFblV5:ReceiverType/en\|Manuals:MBUltraFblV5:Receiver_B/en\|~~SETUPMENU~~\|}}		{{TOC_MBUltraFblV5\|Manuals:MBUltraFblV5:ReceiverType/en\|Manuals:MBUltraFblV5:Receiver_B/en\|RECEIVERMENU\|}}
	__TOC__		__TOC__
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2023-03-02T14:45:30Z

Updating to match new version of source page

← Older revision		Revision as of 14:45, 2 March 2023
Line 11:		Line 11:
	[[File:Receiver_setup_1.png\|x180px\|none]]<br />		[[File:Receiver_setup_1.png\|x180px\|none]]<br />
	<br />		<br />
	In order to detect the receiver you're using, make sure the receiver is connected properly, bound to the radio and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:~~MBULTRAFblV52~~:Radio_System/en\|Radio System]]. Then briefly press the button to start automatic receiver detection routine. The Status LED will indicate the scan process:<br />		In order to detect the receiver you're using, make sure the receiver is connected properly, bound to the radio and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBUltraFblV5:Radio_System/en\|Radio System]]. Then briefly press the button to start automatic receiver detection routine. The Status LED will indicate the scan process:<br />
	<br />		<br />
	{\|cellpadding="4" cellspacing="0" border="1"		{\|cellpadding="4" cellspacing="0" border="1"
Line 49:		Line 49:
	<br />		<br />
	<br />		<br />
	In order to detect the receiver you're using, make sure the receiver is connected properly, bound to the radio and sending out signal. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:~~MBULTRAFblV52~~:Radio_System/en\|Radio System]]. Press the "Scan" button to start automatic receiver detection routine. The ongoing scan process is displayed:<br />		In order to detect the receiver you're using, make sure the receiver is connected properly, bound to the radio and sending out signal. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBUltraFblV5:Radio_System/en\|Radio System]]. Press the "Scan" button to start automatic receiver detection routine. The ongoing scan process is displayed:<br />
	* In case a single-line receiver is used, a dialog will appear on success. This asks how to proceed with function assignments.		* In case a single-line receiver is used, a dialog will appear on success. This asks how to proceed with function assignments.
	* When a Standard receiver is used, the system will restart directly and you can leave the setup screen.		* When a Standard receiver is used, the system will restart directly and you can leave the setup screen.

FuzzyBot: Updating to match new version of source page

2023-03-02T14:40:54Z

Updating to match new version of source page

New page

{{DISPLAYTITLE:Receiver Menu - Type selection|noerror}}
{{TOC_MBUltraFblV5|Manuals:MBUltraFblV5:ReceiverType/en|Manuals:MBUltraFblV5:Receiver_B/en|SETUPMENU|}}
__TOC__
<br />

{{WARNING_QUOTE|Please note that in the first menu points of Receiver Menu there will be no control signal emitted on the throttle output([IO1] or [IO2]). Only at Menu Point '''N''' (Throttle failsafe setting) the output will be activated to check throttle position! '''If you use a speed controller with BEC, disconnect the motor to avoid unintentional starting of the motor!''' On a heli with combustion engine you should remove the servo horn from the throttle servo to avoid linkage binding or breaking the servo horn.}}<br />

=Adjustment on the device=
To get into the RECEIVER MENU press the button on MICROBEAST ULTRA and hold it down before(!) and while turning on the receiver power supply. The yellow Menu LEDs start to cycle immediately. When you release the button, Menu LED '''A''' will be flashing and the color of the Status LED will indicate the receiver type that is selected at the moment.<br />
<br />
[[File:Receiver_setup_1.png|x180px|none]]<br />
<br />
In order to detect the receiver you're using, make sure the receiver is connected properly, bound to the radio and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBULTRAFblV52:Radio_System/en|Radio System]]. Then briefly press the button to start automatic receiver detection routine. The Status LED will indicate the scan process:<br />
<br />
{|cellpadding="4" cellspacing="0" border="1"
!style="width:100px; text-align:left;" | Status-LED !! Receiver type/protocol
|-
|style="color:white; background-color:black"{{!}}off
|Standard receiver
|-
|style="color:white; background-color:#CC66CC"{{!}}purple
|Receiver at remote port
|-
|style="color:white; background-color:#FF3300"{{!}}red
|No receiver detected
|-
|style="color:white; background-color:#0066FF"{{!}}blue
|Receiver at port IO1
|}<br />
* In case a single-line receiver is used, the system will skip to Menu Point '''B''' when a valid input signal was detected.
* When a Standard receiver is used, the system will exit and restart immediately.
* When detection fails, the system will stay at Menu Point '''A''' and the Status LED will flash in red color. Once again, make sure your receiver is connected properly to MICROBEAST ULTRA, make sure the receiver is bound to the transmitter and sending out control signals. Then please try again.<br />
{{NL}}

=Setup with StudioX app=
When StudioX is started and your MICROBEAST ULTRA is connected with StudioX, click the '''Control Setup''' button to show the adjustment options of RECEIVER MENU.<br />
* At the top of the screen you can see which type of input signal is selected at the moment, and which telemetry system/ESC is used (if applicable).
* The rows below show what channels are assigned to which control functions at the moment.
* In the last row you can see the internal value for throttle failsafe position that is set at the moment.<br />
<br />
<div class="iosgallery">
<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20008.PNG">
<div>Choose <b>Control setup</b></div>
</div>
<div class="iosgallery">
<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20011.PNG">
<div class="iostext">Here you can see current receiver system, function assignment and failsafe setting</div>
</div>
<br />
<br />
In order to detect the receiver you're using, make sure the receiver is connected properly, bound to the radio and sending out signal. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBULTRAFblV52:Radio_System/en|Radio System]]. Press the "Scan" button to start automatic receiver detection routine. The ongoing scan process is displayed:<br />
* In case a single-line receiver is used, a dialog will appear on success. This asks how to proceed with function assignments.
* When a Standard receiver is used, the system will restart directly and you can leave the setup screen.
* When detection fails, once again make sure your receiver is connected properly to MICROBEAST ULTRA. Make sure the receiver is bound to the transmitter and sending out control signals. Then please try again.<br />
<br />
<div class="iosgallery">
<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20011.PNG">
<div class="iostext">Click scan button...</div>
</div>
<div class="iosgallery">
<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20014.PNG">
<div class="iostext">...and wait until scan is finished</div>
</div>
<div class="iosgallery">
<img class="ios" src="https://wiki.beastx.com/images/studiox/freakware%202019-07-09%20016.PNG">
<div class="iostext">If scan was successful the dialog will show up</div>
</div>
<br />
<br />