Manuals:MB Plus:Preliminary steps/de - Revision history

Shornstein at 14:54, 27 July 2016

2016-07-27T14:54:26Z

← Older revision		Revision as of 14:54, 27 July 2016
Line 80:		Line 80:

	{{NL}}		{{NL}}
	'''Stellen Sie alle Trimmungen auf neutral und die Servowege auf 100%.''' Durch Vergrößern oder Reduzieren der Servowege auf Heck, Roll und Nick kann später die maximale Drehrate des Helikopters beeinﬂusst werden. Um die Grundeinstellung durchführen zu können, müssen aber die Steuerwege für den Moment unverändert ausgegeben werden. Verstellen Sie auch die Pitchkurve noch nicht, sondern lassen Sie diese wie Standardmäßig vorgegeben von -100% bis +100% (oder je nach Senderfabrikat von 0 bis 100%) verlaufen. Stellen Sie nochmals sicher, dass keinerlei Mischfunktionen wie beispielsweise ein Drehmomentausgleich auf Heck aktiv sind und die Einstellungen und Trimmungen in allen Flugphasen gleich sind. Betrachten Sie den Servomonitor des Fernsteuersenders: Jede Steuerknüppelfunktion darf nur genau einen Kanal betätigen (abgesehen vom Pitchknüppel, der üblicherweise auch den Motor mit ansteuert). Bei Knüppelmittenstellung müssen (in allen Flugphasen) die Kanäle in Mittenposition stehen. Denken Sie daran, dass Sie bei Verwendung von Microbeast PLUS nicht die Servos direkt ansteuern werden, sondern nur per Steuerbefehl dem Gerät mitteilen, wie ~~schell es den Helikopter~~ drehen soll. Jeder Steuerbefehl wird dabei über genau einen Kanal des Fernsteuersenders betätigt.		'''Stellen Sie alle Trimmungen auf neutral und die Servowege auf 100%.''' Durch Vergrößern oder Reduzieren der Servowege auf Heck, Roll und Nick kann später die maximale Drehrate des Helikopters beeinﬂusst werden. Um die Grundeinstellung durchführen zu können, müssen aber die Steuerwege für den Moment unverändert ausgegeben werden. Verstellen Sie auch die Pitchkurve noch nicht, sondern lassen Sie diese wie Standardmäßig vorgegeben von -100% bis +100% (oder je nach Senderfabrikat von 0 bis 100%) verlaufen. Stellen Sie nochmals sicher, dass keinerlei Mischfunktionen wie beispielsweise ein Drehmomentausgleich auf Heck aktiv sind und die Einstellungen und Trimmungen in allen Flugphasen gleich sind. Betrachten Sie den Servomonitor des Fernsteuersenders: Jede Steuerknüppelfunktion darf nur genau einen Kanal betätigen (abgesehen vom Pitchknüppel, der üblicherweise auch den Motor mit ansteuert). Bei Knüppelmittenstellung müssen (in allen Flugphasen) die Kanäle in Mittenposition stehen. Denken Sie daran, dass Sie bei Verwendung von Microbeast PLUS nicht die Servos direkt ansteuern werden, sondern nur per Steuerbefehl dem Gerät mitteilen, wie schnell der Heli drehen soll. Jeder Steuerbefehl wird dabei über genau einen Kanal des Fernsteuersenders betätigt.
	<br />		<br />
	{\|class="gallery" style="font-style: italic"		{\|class="gallery" style="font-style: italic"

Shornstein at 11:31, 18 March 2016

2016-03-18T11:31:29Z

← Older revision		Revision as of 11:31, 18 March 2016
Line 80:		Line 80:

	{{NL}}		{{NL}}
	'''~~Be sure that all trims and sub trims are disabled and that all servo travels are set to~~ 100%.''' ~~Increasing or decreasing the servo travel/stick throw for aileron~~, ~~elevator and rudder will later adjust the (maximum) control rates~~. ~~For the moment to setup Microbeast PLUS let anything stay at default~~. ~~Also do not adjust the collective pitch curve at the moment. For the setup procedures it has to be set as a straight line reaching from~~ -100% to +100% (or 0 to 100% ~~depending on radio brand~~). ~~There mustn't be any active mixing functions~~ (~~for example rudder revo-mixing~~). ~~Have a look at the radio’s servo monitor: each stick has to control one channel/servo output~~ (~~except for thrust stick which typically controls collective pitch and motor~~). ~~Remember when using~~ Microbeast PLUS ~~you do not directly control the servos of the helicopter~~. By moving a stick you give a control command to the Microbeast PLUS unit which then performs the necessary servo movements to move the helictoper in the commanded direction. Each control command is bound to one servo output channel of the transmitter. When using flight modes again make sure that there is no mixing active in any flight mode and that all trims and subtrims are zero in all flight modes.		'''Stellen Sie alle Trimmungen auf neutral und die Servowege auf 100%.''' Durch Vergrößern oder Reduzieren der Servowege auf Heck, Roll und Nick kann später die maximale Drehrate des Helikopters beeinﬂusst werden. Um die Grundeinstellung durchführen zu können, müssen aber die Steuerwege für den Moment unverändert ausgegeben werden. Verstellen Sie auch die Pitchkurve noch nicht, sondern lassen Sie diese wie Standardmäßig vorgegeben von -100% bis +100% (oder je nach Senderfabrikat von 0 bis 100%) verlaufen. Stellen Sie nochmals sicher, dass keinerlei Mischfunktionen wie beispielsweise ein Drehmomentausgleich auf Heck aktiv sind und die Einstellungen und Trimmungen in allen Flugphasen gleich sind. Betrachten Sie den Servomonitor des Fernsteuersenders: Jede Steuerknüppelfunktion darf nur genau einen Kanal betätigen (abgesehen vom Pitchknüppel, der üblicherweise auch den Motor mit ansteuert). Bei Knüppelmittenstellung müssen (in allen Flugphasen) die Kanäle in Mittenposition stehen. Denken Sie daran, dass Sie bei Verwendung von Microbeast PLUS nicht die Servos direkt ansteuern werden, sondern nur per Steuerbefehl dem Gerät mitteilen, wie schell es den Helikopter drehen soll. Jeder Steuerbefehl wird dabei über genau einen Kanal des Fernsteuersenders betätigt.
	<br />		<br />
	{\|class="gallery" style="font-style: italic"		{\|class="gallery" style="font-style: italic"
Line 94:		Line 94:
	{{NL}}		{{NL}}
	<p>		<p>
	'''~~Other functions such as throttle curves~~, ~~ESC switches or auxiliary functions can be adjusted as usual~~.''' ~~When using the RPM Governor function the throttle adjustment will be described later~~. ~~Also the switch assignment for~~ AttitudeControl ~~will be discussed at the specific topic~~.</p>		'''Andere Einstellungen wie z.B. für den Motor oder eventuelle Zusatzkanäle (Beleuchtung, Einziehfahrferwerk, ...) sind wie gewohnt an der Fernsteuerung vorzunehmen.''' Diese sind im Normalfall von der Einstellung des Microbeast PLUS unabhängig. Falls die interne Drehzahlreglerfunktion oder die AttitudeControl verwendet werden soll, so wird auf die Einstellung dieser Zusatzfunktionen an entsprechender Stelle dieser Anleitung eingegangen.</p>
	<br />		<br />
	{{QUOTE\|[[File:Warning.png\|18px\|sub]] '''~~Always make sure that the motor in electric models can not start when doing the adjustment work~~!''' ~~If the drive battery is used as power supply for receiver, servos and Microbeast PLUS~~, ~~disconnect the motor from the ESC~~.}}		{{QUOTE\|[[File:Warning.png\|18px\|sub]] '''Achten Sie unbedingt darauf, dass bei Elektromodellen der Motor während der Einstellarbeiten nicht anlaufen kann!''' Stecken Sie den Motor am besten vom Regler ab, falls der Antriebsakku zur Stromversorgung verwendet wird.}}

Shornstein at 11:27, 18 March 2016

2016-03-18T11:27:33Z

← Older revision		Revision as of 11:27, 18 March 2016
Line 55:		Line 55:
	{{NL}}		{{NL}}

	==~~Preparing the transmitter~~==		==Vorbereiten der Fernsteueranlage==
	~~You can use nearly any transmitter that provides at least~~ 6 ~~channels~~. ~~By default 5 channels are used for controlling~~ Microbeast PLUS ~~and one channel controls the motor~~. ~~If using additional features like~~ AttitudeControl ~~or RPM Governor more channels may be useful to have~~. ~~(Please note the RPM Governor only can be used if you have a [[Manuals:MB_Plus:Receiver_Installation/en#Single-Line_receivers\|single-line receiver]]!)~~.<br />		Es kann nahezu jede Fernsteueranlage mit mindestens 6 Steuerkanälen verwendet werden. Grundsätzlich erfolgt die Bedienung des Microbeast PLUS über 5 Steuerkanäle (der 6. Kanal steuert den Motorsteller oder das Gasservo). Für die Verwendung der optionalen Zusatzfunktionen wie AttitudeControl oder Drehzahlregler für Verbrennerhelis können zusätzliche Steuerkanäle von Vorteil sein. Ausserdem können im Betrieb mit Summensignalempfängern weitere Servoausgänge z.B. für Beleuchtung oder Einziehfahrwerk angesteuert werden, sofern entsprechende Kanäle zur Verfügung stehen.<br />
	{{NL}}		{{NL}}
	'''~~Create a new model~~ in ~~your radio‘s model memory~~.'''		'''Legen Sie in Ihrem Fernsteuersender einen neuen Modellspeicher für Ihr Modell an.'''
	<p>		<p>
	{\|class="gallery" style="font-style: italic"		{\|class="gallery" style="font-style: italic"
Line 68:		Line 68:
	</p>		</p>
	<br />		<br />
	'''~~Disable any mixing functions for the swashplate or rudder. Each function should be assigned to just one receiver channel~~.''' ~~It is advisable to create different flight modes for different flight states~~/~~rotor headspeeds~~. ~~This will allow to set tail gyro gain depending on the flight modes using the radio's tail gyro adjustment menu~~.		'''Achten Sie darauf, dass sämtliche Mischfunktionen deaktiviert sind, die auf die zyklischen Steuerfunktionen und das Heck wirken. Abgesehen vom Pitchsteuerknüppel, muss jeder Steuergeber genau einen Servoausgang am Empfänger ansteuern!''' Es wird empfohlen verschiedene Flugphasen im Sender anzulegen, um getrennte Einstellmöglichkeiten für unterschiedliche Flugzustände/Rotordrehzahlen zu haben. So kann z.B. die Wirkstärke des Heckkreisels abhängig von der Rotordrehzahl unterschiedlich stark eingestellt werden.
	<p>		<p>
	{\|class="gallery" style="font-style: italic"		{\|class="gallery" style="font-style: italic"
Line 76:		Line 76:
	\|}<br />		\|}<br />
	</p>		</p>
	{{QUOTE\|'''~~Never enable your radio‘s eCCPM mixing function~~!''' ~~All the swashplate mixing will be done by~~ Microbeast PLUS. ~~Always set your radio‘s swash mixer to mCCPM~~ (~~mechanical mixing~~) ~~which is often called “H1”, “1 servo” or “normal“ mixing or disable “swash mixing” if applicable~~.}}		{{QUOTE\|'''Verwenden Sie auf keinen Fall die elektronische Taumelscheibenmischung des Fernsteuersenders!''' Diese Aufgabe wird Microbeast PLUS übernehmen. Wählen Sie bei Ihrem Fernsteuersender immer eine mechanische Taumelscheibenmischung aus (oftmals mit „H1“, „1 Servo“ oder „Normal“ bezeichnet) bzw. deaktivieren Sie jegliche Taumelscheibenmischung („No Mix“).}}
	<br />		<br />

FuzzyBot: Updating to match new version of source page

2016-03-18T11:07:14Z

Updating to match new version of source page

← Older revision		Revision as of 11:07, 18 March 2016
Line 67:		Line 67:
	\|}<br />		\|}<br />
	</p>		</p>
	~~{{NL}}~~		<br />
	'''Disable any mixing functions for the swashplate or rudder. Each function should be assigned to just one receiver channel.''' It is advisable to create different flight modes for different flight states/rotor headspeeds. This will allow to set tail gyro gain depending on the flight modes using the radio's tail gyro adjustment menu.		'''Disable any mixing functions for the swashplate or rudder. Each function should be assigned to just one receiver channel.''' It is advisable to create different flight modes for different flight states/rotor headspeeds. This will allow to set tail gyro gain depending on the flight modes using the radio's tail gyro adjustment menu.
	<p>		<p>
Line 77:		Line 77:
	</p>		</p>
	{{QUOTE\|'''Never enable your radio‘s eCCPM mixing function!''' All the swashplate mixing will be done by Microbeast PLUS. Always set your radio‘s swash mixer to mCCPM (mechanical mixing) which is often called “H1”, “1 servo” or “normal“ mixing or disable “swash mixing” if applicable.}}		{{QUOTE\|'''Never enable your radio‘s eCCPM mixing function!''' All the swashplate mixing will be done by Microbeast PLUS. Always set your radio‘s swash mixer to mCCPM (mechanical mixing) which is often called “H1”, “1 servo” or “normal“ mixing or disable “swash mixing” if applicable.}}
	~~{{NL}}~~		<br />

	{{NL}}		{{NL}}

FuzzyBot: Updating to match new version of source page

2016-03-18T11:03:47Z

Updating to match new version of source page

← Older revision		Revision as of 11:03, 18 March 2016
Line 56:		Line 56:

	==Preparing the transmitter==		==Preparing the transmitter==
	You can use nearly any transmitter that provides at least 6 channels. By default 5 channels are used for controlling Microbeast PLUS and one channel controls the motor. If using additional features like AttitudeControl or RPM Governor more channels may be useful to have. (Please note the RPM Governor only can be used if you have a [[Manuals:MB_Plus:Receiver_Installation/en#Single-Line_receivers\|single-line receiver]]!).~~{{NL}}~~		You can use nearly any transmitter that provides at least 6 channels. By default 5 channels are used for controlling Microbeast PLUS and one channel controls the motor. If using additional features like AttitudeControl or RPM Governor more channels may be useful to have. (Please note the RPM Governor only can be used if you have a [[Manuals:MB_Plus:Receiver_Installation/en#Single-Line_receivers\|single-line receiver]]!).<br />
	{{NL}}		{{NL}}
	'''Create a new model in your radio‘s model memory.'''		'''Create a new model in your radio‘s model memory.'''
Line 79:		Line 79:
	{{NL}}		{{NL}}

	~~{{NL}}~~
	{{NL}}		{{NL}}
	'''Be sure that all trims and sub trims are disabled and that all servo travels are set to 100%.''' Increasing or decreasing the servo travel/stick throw for aileron, elevator and rudder will later adjust the (maximum) control rates. For the moment to setup Microbeast PLUS let anything stay at default. Also do not adjust the collective pitch curve at the moment. For the setup procedures it has to be set as a straight line reaching from -100% to +100% (or 0 to 100% depending on radio brand). There mustn't be any active mixing functions (for example rudder revo-mixing). Have a look at the radio’s servo monitor: each stick has to control one channel/servo output (except for thrust stick which typically controls collective pitch and motor). Remember when using Microbeast PLUS you do not directly control the servos of the helicopter. By moving a stick you give a control command to the Microbeast PLUS unit which then performs the necessary servo movements to move the helictoper in the commanded direction. Each control command is bound to one servo output channel of the transmitter. When using flight modes again make sure that there is no mixing active in any flight mode and that all trims and subtrims are zero in all flight modes.		'''Be sure that all trims and sub trims are disabled and that all servo travels are set to 100%.''' Increasing or decreasing the servo travel/stick throw for aileron, elevator and rudder will later adjust the (maximum) control rates. For the moment to setup Microbeast PLUS let anything stay at default. Also do not adjust the collective pitch curve at the moment. For the setup procedures it has to be set as a straight line reaching from -100% to +100% (or 0 to 100% depending on radio brand). There mustn't be any active mixing functions (for example rudder revo-mixing). Have a look at the radio’s servo monitor: each stick has to control one channel/servo output (except for thrust stick which typically controls collective pitch and motor). Remember when using Microbeast PLUS you do not directly control the servos of the helicopter. By moving a stick you give a control command to the Microbeast PLUS unit which then performs the necessary servo movements to move the helictoper in the commanded direction. Each control command is bound to one servo output channel of the transmitter. When using flight modes again make sure that there is no mixing active in any flight mode and that all trims and subtrims are zero in all flight modes.
Line 92:		Line 91:
	\|-		\|-
	\|width="600pt" style="padding:0px 30px;" align="center"\|[[Image:Other_functions.png\|192px\|none\|border]]		\|width="600pt" style="padding:0px 30px;" align="center"\|[[Image:Other_functions.png\|192px\|none\|border]]
	\|}~~{{NL}}~~		\|}<br />
	{{NL}}		{{NL}}
	<p>		<p>

FuzzyBot: Updating to match new version of source page

2016-03-18T10:59:45Z

Updating to match new version of source page

← Older revision		Revision as of 10:59, 18 March 2016
Line 80:		Line 80:

	{{NL}}		{{NL}}
	~~<p>~~		{{NL}}
	'''Be sure that all trims and sub trims are disabled and that all servo travels are set to 100%.''' Increasing or decreasing the servo travel/stick throw for aileron, elevator and rudder will later adjust the (maximum) control rates. For the moment to setup Microbeast PLUS let anything stay at default. Also do not adjust the collective pitch curve at the moment. For the setup procedures it has to be set as a straight line reaching from -100% to +100% (or 0 to 100% depending on radio brand). There mustn't be any active mixing functions (for example rudder revo-mixing). Have a look at the radio’s servo monitor: each stick has to control one channel/servo output (except for thrust stick which typically controls collective pitch and motor). Remember when using Microbeast PLUS you do not directly control the servos of the helicopter. By moving a stick you give a control command to the Microbeast PLUS unit which then performs the necessary servo movements to move the helictoper in the commanded direction. Each control command is bound to one servo output channel of the transmitter. When using flight modes again make sure that there is no mixing active in any flight mode and that all trims and subtrims are zero in all flight modes.~~</p>~~		'''Be sure that all trims and sub trims are disabled and that all servo travels are set to 100%.''' Increasing or decreasing the servo travel/stick throw for aileron, elevator and rudder will later adjust the (maximum) control rates. For the moment to setup Microbeast PLUS let anything stay at default. Also do not adjust the collective pitch curve at the moment. For the setup procedures it has to be set as a straight line reaching from -100% to +100% (or 0 to 100% depending on radio brand). There mustn't be any active mixing functions (for example rudder revo-mixing). Have a look at the radio’s servo monitor: each stick has to control one channel/servo output (except for thrust stick which typically controls collective pitch and motor). Remember when using Microbeast PLUS you do not directly control the servos of the helicopter. By moving a stick you give a control command to the Microbeast PLUS unit which then performs the necessary servo movements to move the helictoper in the commanded direction. Each control command is bound to one servo output channel of the transmitter. When using flight modes again make sure that there is no mixing active in any flight mode and that all trims and subtrims are zero in all flight modes.
	<br />		<br />
	{\|class="gallery" style="font-style: italic"		{\|class="gallery" style="font-style: italic"

FuzzyBot: Updating to match new version of source page

2016-03-18T10:42:43Z

Updating to match new version of source page

← Older revision		Revision as of 10:42, 18 March 2016
Line 56:		Line 56:

	==Preparing the transmitter==		==Preparing the transmitter==
	You can use nearly any transmitter that provides at least 6 channels. By default 5 channels are used for controlling Microbeast PLUS and one channel controls the motor. If using additional features like AttitudeControl or RPM Governor more channels may be useful to have. (Please note the RPM Governor only can be used if you have a [[Manuals:MB_Plus:Receiver_Installation/en#Single-Line_receivers\|single-line receiver]]!).~~<br />~~		You can use nearly any transmitter that provides at least 6 channels. By default 5 channels are used for controlling Microbeast PLUS and one channel controls the motor. If using additional features like AttitudeControl or RPM Governor more channels may be useful to have. (Please note the RPM Governor only can be used if you have a [[Manuals:MB_Plus:Receiver_Installation/en#Single-Line_receivers\|single-line receiver]]!).{{NL}}
	{{NL}}		{{NL}}
	'''Create a new model in your radio‘s model memory.'''		'''Create a new model in your radio‘s model memory.'''
Line 67:		Line 67:
	\|}<br />		\|}<br />
	</p>		</p>
	~~<br />~~		{{NL}}
	'''Disable any mixing functions for the swashplate or rudder. Each function should be assigned to just one receiver channel.''' It is advisable to create different flight modes for different flight states/rotor headspeeds. This will allow to set tail gyro gain depending on the flight modes using the radio's tail gyro adjustment menu.		'''Disable any mixing functions for the swashplate or rudder. Each function should be assigned to just one receiver channel.''' It is advisable to create different flight modes for different flight states/rotor headspeeds. This will allow to set tail gyro gain depending on the flight modes using the radio's tail gyro adjustment menu.
	<p>		<p>
Line 77:		Line 77:
	</p>		</p>
	{{QUOTE\|'''Never enable your radio‘s eCCPM mixing function!''' All the swashplate mixing will be done by Microbeast PLUS. Always set your radio‘s swash mixer to mCCPM (mechanical mixing) which is often called “H1”, “1 servo” or “normal“ mixing or disable “swash mixing” if applicable.}}		{{QUOTE\|'''Never enable your radio‘s eCCPM mixing function!''' All the swashplate mixing will be done by Microbeast PLUS. Always set your radio‘s swash mixer to mCCPM (mechanical mixing) which is often called “H1”, “1 servo” or “normal“ mixing or disable “swash mixing” if applicable.}}
	~~<br />~~		{{NL}}

	~~<br />~~		{{NL}}
	<p>		<p>
	'''Be sure that all trims and sub trims are disabled and that all servo travels are set to 100%.''' Increasing or decreasing the servo travel/stick throw for aileron, elevator and rudder will later adjust the (maximum) control rates. For the moment to setup Microbeast PLUS let anything stay at default. Also do not adjust the collective pitch curve at the moment. For the setup procedures it has to be set as a straight line reaching from -100% to +100% (or 0 to 100% depending on radio brand). There mustn't be any active mixing functions (for example rudder revo-mixing). Have a look at the radio’s servo monitor: each stick has to control one channel/servo output (except for thrust stick which typically controls collective pitch and motor). Remember when using Microbeast PLUS you do not directly control the servos of the helicopter. By moving a stick you give a control command to the Microbeast PLUS unit which then performs the necessary servo movements to move the helictoper in the commanded direction. Each control command is bound to one servo output channel of the transmitter. When using flight modes again make sure that there is no mixing active in any flight mode and that all trims and subtrims are zero in all flight modes.</p>		'''Be sure that all trims and sub trims are disabled and that all servo travels are set to 100%.''' Increasing or decreasing the servo travel/stick throw for aileron, elevator and rudder will later adjust the (maximum) control rates. For the moment to setup Microbeast PLUS let anything stay at default. Also do not adjust the collective pitch curve at the moment. For the setup procedures it has to be set as a straight line reaching from -100% to +100% (or 0 to 100% depending on radio brand). There mustn't be any active mixing functions (for example rudder revo-mixing). Have a look at the radio’s servo monitor: each stick has to control one channel/servo output (except for thrust stick which typically controls collective pitch and motor). Remember when using Microbeast PLUS you do not directly control the servos of the helicopter. By moving a stick you give a control command to the Microbeast PLUS unit which then performs the necessary servo movements to move the helictoper in the commanded direction. Each control command is bound to one servo output channel of the transmitter. When using flight modes again make sure that there is no mixing active in any flight mode and that all trims and subtrims are zero in all flight modes.</p>
Line 92:		Line 92:
	\|-		\|-
	\|width="600pt" style="padding:0px 30px;" align="center"\|[[Image:Other_functions.png\|192px\|none\|border]]		\|width="600pt" style="padding:0px 30px;" align="center"\|[[Image:Other_functions.png\|192px\|none\|border]]
	\|}~~<br />~~		\|}{{NL}}
	~~<br />~~		{{NL}}
	<p>		<p>
	'''Other functions such as throttle curves, ESC switches or auxiliary functions can be adjusted as usual.''' When using the RPM Governor function the throttle adjustment will be described later. Also the switch assignment for AttitudeControl will be discussed at the specific topic.</p>		'''Other functions such as throttle curves, ESC switches or auxiliary functions can be adjusted as usual.''' When using the RPM Governor function the throttle adjustment will be described later. Also the switch assignment for AttitudeControl will be discussed at the specific topic.</p>
	<br />		<br />
	{{QUOTE\|[[File:Warning.png\|18px\|sub]] '''Always make sure that the motor in electric models can not start when doing the adjustment work!''' If the drive battery is used as power supply for receiver, servos and Microbeast PLUS, disconnect the motor from the ESC.}}		{{QUOTE\|[[File:Warning.png\|18px\|sub]] '''Always make sure that the motor in electric models can not start when doing the adjustment work!''' If the drive battery is used as power supply for receiver, servos and Microbeast PLUS, disconnect the motor from the ESC.}}

FuzzyBot: Updating to match new version of source page

2016-03-18T10:27:58Z

Updating to match new version of source page

← Older revision		Revision as of 10:27, 18 March 2016
Line 57:		Line 57:
	==Preparing the transmitter==		==Preparing the transmitter==
	You can use nearly any transmitter that provides at least 6 channels. By default 5 channels are used for controlling Microbeast PLUS and one channel controls the motor. If using additional features like AttitudeControl or RPM Governor more channels may be useful to have. (Please note the RPM Governor only can be used if you have a [[Manuals:MB_Plus:Receiver_Installation/en#Single-Line_receivers\|single-line receiver]]!).<br />		You can use nearly any transmitter that provides at least 6 channels. By default 5 channels are used for controlling Microbeast PLUS and one channel controls the motor. If using additional features like AttitudeControl or RPM Governor more channels may be useful to have. (Please note the RPM Governor only can be used if you have a [[Manuals:MB_Plus:Receiver_Installation/en#Single-Line_receivers\|single-line receiver]]!).<br />
	~~<br />~~		{{NL}}
	'''Create a new model in your radio‘s model memory.'''		'''Create a new model in your radio‘s model memory.'''
	<p>		<p>

FuzzyBot: Updating to match new version of source page

2016-03-18T10:21:52Z

Updating to match new version of source page

← Older revision		Revision as of 10:21, 18 March 2016
Line 55:		Line 55:
	{{NL}}		{{NL}}

	==~~Vorbereiten der Fernsteueranlage~~==		==Preparing the transmitter==
			You can use nearly any transmitter that provides at least 6 channels. By default 5 channels are used for controlling Microbeast PLUS and one channel controls the motor. If using additional features like AttitudeControl or RPM Governor more channels may be useful to have. (Please note the RPM Governor only can be used if you have a [[Manuals:MB_Plus:Receiver_Installation/en#Single-Line_receivers\|single-line receiver]]!).<br />
			<br />
			'''Create a new model in your radio‘s model memory.'''
	<p>		<p>
	~~Es kann nahezu jede Fernsteueranlage mit mindestens 6 Steuerkanälen verwendet werden~~. ~~Grundsätzlich erfolgt die Bedienung des Microbeast PLUS über 5 Steuerkanäle~~. ~~Der 6~~. ~~Kanal steuert den Motorsteller oder das Gasservo~~. ~~Für die Verwendung der optionalen Zusatzfunktionen wie AttitudeControl oder Drehzahlregler für Verbrennerhelis können zusätzliche Steuerkanäle von Vorteil sein~~. ~~Ausserdem können im Betrieb mit Summensignalempfängern weitere Servoausgänge z.B~~. ~~für Beleuchtung oder Einziehfahrwerk angesteuert werden, sofern entsprechende Kanäle zur Verfügung stehen~~.~~</p>~~		{\|class="gallery" style="font-style: italic"
			\|-
			\|width="200pt" style="padding:0px 10px;" align="center"\|[[Image:SPM_0061.png\|192px\|none\|border]]
			\|width="200pt" style="padding:0px 10px;" align="center"\|[[Image:SPM_0064.png\|192px\|none\|border]]
			\|width="200pt" style="padding:0px 10px;" align="center"\|[[Image:SPM_0060.png\|192px\|none\|border]]
			\|}<br />
			</p>
			<br />
			'''Disable any mixing functions for the swashplate or rudder. Each function should be assigned to just one receiver channel.''' It is advisable to create different flight modes for different flight states/rotor headspeeds. This will allow to set tail gyro gain depending on the flight modes using the radio's tail gyro adjustment menu.
	<p>		<p>
	~~Legen Sie in Ihrem Fernsteuersender einen neuen Modellspeicher für Ihr Modell an~~. ~~Achten Sie darauf, dass sämtliche Mischfunktionen deaktiviert sind, die auf die zyklischen Steuerfunktionen und das Heck wirken~~. ~~Abgesehen vom Pitchsteuerknüppel, muss jeder Steuergeber genau einen Servoausgang am Empfänger ansteuern!~~</p>		{\|class="gallery" style="font-style: italic"
			\|-
			\|width="200pt" style="padding:0px 10px;" align="center"\|[[Image:SPM_0062.png\|192px\|none\|border]]
			\|width="200pt" style="padding:0px 10px;" align="center"\|[[Image:SPM_0067.png\|192px\|none\|border]]
			\|}<br />
			</p>
			{{QUOTE\|'''Never enable your radio‘s eCCPM mixing function!''' All the swashplate mixing will be done by Microbeast PLUS. Always set your radio‘s swash mixer to mCCPM (mechanical mixing) which is often called “H1”, “1 servo” or “normal“ mixing or disable “swash mixing” if applicable.}}
	<br />		<br />
	{{QUOTE\|'''Verwenden Sie auf keinen Fall die elektronische Taumelscheibenmischung des Fernsteuersenders!''' Diese Aufgabe wird Microbeast PLUS übernehmen. Wählen Sie bei Ihrem Fernsteuersender immer eine mechanische Taumelscheibenmischung aus (oftmals mit „H1“, „1 Servo“ oder „Normal“ bezeichnet) bzw. deaktivieren Sie jegliche Taumelscheibenmischung („No Mix“).}}
	<br />		<br />

	<p>		<p>
	~~Stellen Sie alle Trimmungen auf neutral und die Servowege auf~~ 100%. ~~Durch Vergrößerung oder Reduzierung der Servowege auf Heck~~, ~~Roll und Nick können Sie später die maximale Drehrate des Helikopters beeinﬂussen~~. ~~Um die Grundeinstellung durchführen zu können, müssen aber die Steuerwege für den Moment unverändert ausgegeben werden~~. ~~Verstellen Sie auch die Pitchkurve noch nicht, sondern lassen Sie diese wie Standardmäßig vorgegeben von~~ -100% ~~bis~~ +100% (~~oder je nach Senderfabrikat von~~ 0 ~~bis~~ 100%) ~~verlaufen~~.</p>		'''Be sure that all trims and sub trims are disabled and that all servo travels are set to 100%.''' Increasing or decreasing the servo travel/stick throw for aileron, elevator and rudder will later adjust the (maximum) control rates. For the moment to setup Microbeast PLUS let anything stay at default. Also do not adjust the collective pitch curve at the moment. For the setup procedures it has to be set as a straight line reaching from -100% to +100% (or 0 to 100% depending on radio brand). There mustn't be any active mixing functions (for example rudder revo-mixing). Have a look at the radio’s servo monitor: each stick has to control one channel/servo output (except for thrust stick which typically controls collective pitch and motor). Remember when using Microbeast PLUS you do not directly control the servos of the helicopter. By moving a stick you give a control command to the Microbeast PLUS unit which then performs the necessary servo movements to move the helictoper in the commanded direction. Each control command is bound to one servo output channel of the transmitter. When using flight modes again make sure that there is no mixing active in any flight mode and that all trims and subtrims are zero in all flight modes.</p>
	<p>		<br />
	~~Stellen Sie nochmals sicher, dass keinerlei Mischfunktionen wie beispielsweise ein Drehmomentausgleich auf Heck aktiv sind und die Einstellungen und Trimmungen in allen Flugphasen gleich sind~~. ~~Betrachten Sie den Servomonitor des Fernsteuersenders~~: ~~Jede Steuerknüppelfunktion darf nur genau einen Kanal betätigen (abgesehen vom Pitchknüppel, der üblicherweise auch den Motor mit ansteuert)~~. ~~Bei Knüppelmittenstellung müssen (in allen Flugphasen) die Kanäle in Mittenposition stehen~~. Denken Sie daran, dass Sie bei Verwendung von Microbeast PLUS nicht die Servos direkt ansteuern werden, sondern nur per Steuerbefehl dem Gerät mitteilen, wie schell es den Helikopter drehen soll. Jeder Steuerbefehl wird dabei über genau einen Kanal des Fernsteuersenders betätigt.</p>		{\|class="gallery" style="font-style: italic"
			\|-
			\|width="200pt" style="padding:0px 10px;" align="center"\|[[Image:SPM_0095.png\|192px\|none\|border]]
			\|width="200pt" style="padding:0px 10px;" align="center"\|[[Image:SPM_0080.png\|192px\|none\|border]]
			\|width="200pt" style="padding:0px 10px;" align="center"\|[[Image:SPM_0081.png\|192px\|none\|border]]
			\|}<br />
			{\|class="gallery" style="font-style: italic"
			\|-
			\|width="600pt" style="padding:0px 30px;" align="center"\|[[Image:Other_functions.png\|192px\|none\|border]]
			\|}<br />
			<br />
	<p>		<p>
	~~Andere Einstellungen wie z.B. für den Motor oder eventuelle Zusatzkanäle (Beleuchtung, Einziehfahrferwerk~~, ..~~.) sind wie gewohnt an der Fernsteuerung vorzunehmen. Diese sind im Normalfall von der Einstellung des Microbeast PLUS unabhängig. Falls Sie die Drehzahlreglerfunktion oder die~~ AttitudeControl ~~verwenden, so wird auf die Einstellung dieser Steuerfunktionen an entsprechender Stelle eingegangen~~.</p>		'''Other functions such as throttle curves, ESC switches or auxiliary functions can be adjusted as usual.''' When using the RPM Governor function the throttle adjustment will be described later. Also the switch assignment for AttitudeControl will be discussed at the specific topic.</p>
	<br />		<br />
	{{QUOTE\|[[File:Warning.png\|18px\|sub]] '''~~Achten Sie unbedingt darauf, dass bei Elektromodellen der Motor während der Einstellarbeiten nicht anlaufen kann~~!''' ~~Stecken Sie den Motor am besten vom Regler ab~~, ~~falls der Antriebsakku zur Stromversorgung verwendet wird~~.}}		{{QUOTE\|[[File:Warning.png\|18px\|sub]] '''Always make sure that the motor in electric models can not start when doing the adjustment work!''' If the drive battery is used as power supply for receiver, servos and Microbeast PLUS, disconnect the motor from the ESC.}}

Shornstein at 12:39, 19 November 2015

2015-11-19T12:39:46Z

← Older revision		Revision as of 12:39, 19 November 2015
Line 55:		Line 55:
	{{NL}}		{{NL}}

	==~~Preparing the transmitter~~==		==Vorbereiten der Fernsteueranlage==
	~~You can use nearly any transmitter that provides at least~~ 6 ~~channels~~. ~~By default 5 channels are used for controlling~~ Microbeast PLUS ~~and one channel controls the motor~~. ~~If using additional features like~~ AttitudeControl ~~or (nitro) RPM Governor more channels may be useful to have~~.<br />		<p>
			Es kann nahezu jede Fernsteueranlage mit mindestens 6 Steuerkanälen verwendet werden. Grundsätzlich erfolgt die Bedienung des Microbeast PLUS über 5 Steuerkanäle. Der 6. Kanal steuert den Motorsteller oder das Gasservo. Für die Verwendung der optionalen Zusatzfunktionen wie AttitudeControl oder Drehzahlregler für Verbrennerhelis können zusätzliche Steuerkanäle von Vorteil sein. Ausserdem können im Betrieb mit Summensignalempfängern weitere Servoausgänge z.B. für Beleuchtung oder Einziehfahrwerk angesteuert werden, sofern entsprechende Kanäle zur Verfügung stehen.</p>
			<p>
			Legen Sie in Ihrem Fernsteuersender einen neuen Modellspeicher für Ihr Modell an. Achten Sie darauf, dass sämtliche Mischfunktionen deaktiviert sind, die auf die zyklischen Steuerfunktionen und das Heck wirken. Abgesehen vom Pitchsteuerknüppel, muss jeder Steuergeber genau einen Servoausgang am Empfänger ansteuern!</p>
	<br />		<br />
	~~Create a new model in your radio‘s model memory. Disable any mixing functions for the swashplate or rudder. Each function should be assigned to just one receiver channel.<br />~~		{{QUOTE\|'''Verwenden Sie auf keinen Fall die elektronische Taumelscheibenmischung des Fernsteuersenders!''' Diese Aufgabe wird Microbeast PLUS übernehmen. Wählen Sie bei Ihrem Fernsteuersender immer eine mechanische Taumelscheibenmischung aus (oftmals mit „H1“, „1 Servo“ oder „Normal“ bezeichnet) bzw. deaktivieren Sie jegliche Taumelscheibenmischung („No Mix“).}}
	~~<br />~~
	{{QUOTE\|'''~~Never enable your radio‘s eCCPM mixing function~~!''' ~~All the swashplate mixing will be done by~~ Microbeast PLUS. ~~Always set your radio‘s swash mixer to mCCPM~~ (~~mechanical mixing~~) ~~which is often called “H1”, “1 servo” or “normal“ mixing or disable “swash mixing” if applicable~~.}}
	<br />		<br />