Translations:Help:AttitudeControl/6/en - Revision history

FuzzyBot: Importing a new version from external source

2015-11-06T16:02:33Z

Importing a new version from external source

← Older revision		Revision as of 16:02, 6 November 2015
Line 1:		Line 1:
	===AttitudeControl can not be activated although it is switched on at Parameter menu point M===		===AttitudeControl can not be activated although it is switched on at Parameter menu point M===
	When using a single-line receiver you must go into Receiver setup menu and assign the switch channel for AttitudeControl either by moving the switch on the transmitter at Receiver menu point J, by loading the default assignment or by skipping menu point J in order to use the gyro channel for the AttitudeControl.		When using MICROBEAST PLUS with a single-line receiver you must go into Receiver setup menu and assign the switch channel for AttitudeControl either by moving the switch on the transmitter at Receiver menu point J, by loading the default assignment or by skipping menu point J in order to use the gyro channel for the AttitudeControl.
	'''Also when using a standard receiver you must go into receiver menu once, select "Standard receiver" as type at menu point A (if not done already) and then confirm the type selection by briefly pressing the button'''. If you don't do this the assignment gyro channel<->AttitudeControl is not set and you won't be able to switch AttitudeControl on and off. (Only applies to Fimware Version 4.0.0 and lower!)<br />		'''Also when using a standard receiver you must go into receiver menu once, select "Standard receiver" as type at menu point A (if not done already) and then confirm the type selection by briefly pressing the button'''. If you don't do this the assignment gyro channel<->AttitudeControl is not set and you won't be able to switch AttitudeControl on and off. (Only applies to Fimware Version 4.0.0 and lower!)<br />
	<br />		<br />
	{{QUOTE\|Please note that after adjusting the receiver setup menu for safety reason AttitudeControl (and also the RPM Governor function) will be reset to default. So after doing the adjustment in receiver menu select your desired AttitudeControl mode a Parameter menu point M again. Otherwise it will still not work. (Only applies to Fimware Version 4.0.0 and lower!)}}<br />		{{QUOTE\|Please note that after adjusting the receiver setup menu for safety reason AttitudeControl (and also the RPM Governor function) will be reset to default. So after doing the adjustment in receiver menu select your desired AttitudeControl mode a Parameter menu point M again. Otherwise it will still not work. (Only applies to Fimware Version 4.0.0 and lower!)}}<br />

FuzzyBot: Importing a new version from external source

2015-11-05T10:05:41Z

Importing a new version from external source

← Older revision		Revision as of 10:05, 5 November 2015
Line 1:		Line 1:
	===AttitudeControl can not be activated although it is switched on at Parameter menu point M===		===AttitudeControl can not be activated although it is switched on at Parameter menu point M===
	When using a single-line receiver you must go into Receiver setup menu and assign the switch channel for AttitudeControl either by moving the switch on the transmitter at Receiver menu point J, by loading the default assignment or by skipping menu point J in order to use the gyro channel for the AttitudeControl.		When using a single-line receiver you must go into Receiver setup menu and assign the switch channel for AttitudeControl either by moving the switch on the transmitter at Receiver menu point J, by loading the default assignment or by skipping menu point J in order to use the gyro channel for the AttitudeControl.
	Also when using a standard receiver you must go into receiver menu, select "Standard receiver" as type at menu point A (if not done already) and then confirm the type selection by pressing the button ~~short~~. If you don't do this the assignment gyro channel<->AttitudeControl is not set and you won't be able to switch AttitudeControl on and off.<br />		'''Also when using a standard receiver you must go into receiver menu once, select "Standard receiver" as type at menu point A (if not done already) and then confirm the type selection by briefly pressing the button'''. If you don't do this the assignment gyro channel<->AttitudeControl is not set and you won't be able to switch AttitudeControl on and off. (Only applies to Fimware Version 4.0.0 and lower!)<br />
	<br />		<br />
	{{QUOTE\|Please note that after adjusting the receiver setup menu for safety reason AttitudeControl (and also the RPM Governor function) will be reset to default. So after doing the adjustment in receiver menu select your desired AttitudeControl mode a Parameter menu point M again. Otherwise it will still not work.}}<br />		{{QUOTE\|Please note that after adjusting the receiver setup menu for safety reason AttitudeControl (and also the RPM Governor function) will be reset to default. So after doing the adjustment in receiver menu select your desired AttitudeControl mode a Parameter menu point M again. Otherwise it will still not work. (Only applies to Fimware Version 4.0.0 and lower!)}}<br />

Shornstein: Created page with "===AttitudeControl can not be activated although it is switched on at Parameter menu point M=== When using a single-line receiver you must go into Receiver setup menu and assi..."

2015-05-15T19:28:47Z

Created page with "===AttitudeControl can not be activated although it is switched on at Parameter menu point M=== When using a single-line receiver you must go into Receiver setup menu and assi..."

New page

===AttitudeControl can not be activated although it is switched on at Parameter menu point M===
When using a single-line receiver you must go into Receiver setup menu and assign the switch channel for AttitudeControl either by moving the switch on the transmitter at Receiver menu point J, by loading the default assignment or by skipping menu point J in order to use the gyro channel for the AttitudeControl.
Also when using a standard receiver you must go into receiver menu, select "Standard receiver" as type at menu point A (if not done already) and then confirm the type selection by pressing the button short. If you don't do this the assignment gyro channel<->AttitudeControl is not set and you won't be able to switch AttitudeControl on and off.<br />
<br />
{{QUOTE|Please note that after adjusting the receiver setup menu for safety reason AttitudeControl (and also the RPM Governor function) will be reset to default. So after doing the adjustment in receiver menu select your desired AttitudeControl mode a Parameter menu point M again. Otherwise it will still not work.}}<br />