Translations:Help:FAQ/23/en - Revision history

FuzzyBot: Importing a new version from external source

2015-05-27T08:38:00Z

Importing a new version from external source

← Older revision		Revision as of 08:38, 27 May 2015
Line 1:		Line 1:
	===Helicopter tips over when trying to take off or tilts to one side in flight.===		===Helicopter tips over when trying to take off or tilts to one side in flight.===
	* Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly (Setup menu point M)!		* Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly ([[Manuals:MB_Plus:Setupmenu_M\|Setup menu point '''M''']])!

FuzzyBot: Importing a new version from external source

2014-08-26T13:07:02Z

Importing a new version from external source

← Older revision		Revision as of 13:07, 26 August 2014
Line 1:		Line 1:
	===Helicopter tips over when trying to take off or tilts to one side in flight.===		===Helicopter tips over when trying to take off or tilts to one side in flight.===
	Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly (Setup menu point M)!		* Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly (Setup menu point M)!

FuzzyBot: Importing a new version from external source

2013-12-17T16:06:37Z

Importing a new version from external source

← Older revision		Revision as of 16:06, 17 December 2013
Line 1:		Line 1:
	===Helicopter tips over when trying to take off or tilts to one side in flight.===		===Helicopter tips over when trying to take off or tilts to one side in flight.===
	* Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly (Setup menu point M)!		Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly (Setup menu point M)!

FuzzyBot: Importing a new version from external source

2013-12-17T15:35:20Z

Importing a new version from external source

← Older revision		Revision as of 15:35, 17 December 2013
Line 1:		Line 1:
	===Helicopter tips over when trying to take off or tilts to one side in flight.===		===Helicopter tips over when trying to take off or tilts to one side in flight.===
	Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly (Setup menu point M)!		* Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly (Setup menu point M)!

FuzzyBot: Importing a new version from external source

2013-12-17T15:33:03Z

Importing a new version from external source

New page

===Helicopter tips over when trying to take off or tilts to one side in flight.===
Please check whether everything works properly on the ground. When giving collective pitch input the swash should move up and down properly. When giving cyclic input it should return to zero after a few seconds. This is also especially after turning on Idle up or switching between flight conditions in the transmitter. Make sure that there are no trims, mixers, etc. in any flight condition and also make sure that the sensor directions for aileron and elevator are setup correctly (Setup menu point M)!