Translations:Manuals:BXFbl:Radio Setup:FRSKY/13/en - Revision history

FuzzyBot: Importing a new version from external source

2024-04-30T19:56:04Z

Importing a new version from external source

← Older revision		Revision as of 19:56, 30 April 2024
Line 2:		Line 2:
	You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. For further informations please refer to the StudioX instruction notes.<br />		You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. For further informations please refer to the StudioX instruction notes.<br />
	<br />		<br />
	Please note that when using S.PORT ~~(inv.)~~ telemetry connected to [SYS], you must disconnect the receiver from [SYS] temporarily, switch off your radio and power cycle your device. It will then enable "normal" [SYS] operation for programming purpose. When using F.Port connected at [SYS] in combination with MICROBEAST ULTRA you can connect your BLE2SYS/USB2SYS at the DI2 port at the side of the device using the [https://www.freakware.de/en/p/adapter-cable-telemetry-adapterkabel-micobeast-beastx-bxa76406-a174871.htm Telemetry adapter cable BXA76406].<br />		Please note that when using S.PORT telemetry connected to [SYS], you must disconnect the receiver from [SYS] temporarily, switch off your radio and power cycle your device. It will then enable "normal" [SYS] operation for programming purpose. When using F.Port connected at [SYS] in combination with MICROBEAST ULTRA you can connect your BLE2SYS/USB2SYS at the DI2 port at the side of the device using the [https://www.freakware.de/en/p/adapter-cable-telemetry-adapterkabel-micobeast-beastx-bxa76406-a174871.htm Telemetry adapter cable BXA76406].<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2024-04-25T09:14:20Z

Importing a new version from external source

← Older revision		Revision as of 09:14, 25 April 2024
Line 1:		Line 1:
	==Setup with StudioX==		==Setup with StudioX==
	You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. Please note that when using S.PORT telemetry connected to [SYS], you must disconnect the receiver from [SYS]temporarily, switch off your radio and power cycle your device. It will then enable "normal" [SYS] operation for programming purpose. ~~For further informations please refer to~~ the ~~StudioX instruction notes~~.<br />		You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. For further informations please refer to the StudioX instruction notes.<br />
			<br />
			Please note that when using S.PORT (inv.) telemetry connected to [SYS], you must disconnect the receiver from [SYS] temporarily, switch off your radio and power cycle your device. It will then enable "normal" [SYS] operation for programming purpose. When using F.Port connected at [SYS] in combination with MICROBEAST ULTRA you can connect your BLE2SYS/USB2SYS at the DI2 port at the side of the device using the [https://www.freakware.de/en/p/adapter-cable-telemetry-adapterkabel-micobeast-beastx-bxa76406-a174871.htm Telemetry adapter cable BXA76406].<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2024-04-23T07:06:23Z

Importing a new version from external source

← Older revision		Revision as of 07:06, 23 April 2024
Line 1:		Line 1:
	==Setup with StudioX==		==Setup with StudioX==
	You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. Please note that when ~~the RX line of the receiver is~~ connected to SYS ~~port~~, you must disconnect the receiver from SYS temporarily, switch off your radio and power cycle your device. It will then enable "normal" SYS operation for programming purpose. For further informations please refer to the StudioX instruction notes.<br />		You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. Please note that when using S.PORT telemetry connected to [SYS], you must disconnect the receiver from [SYS]temporarily, switch off your radio and power cycle your device. It will then enable "normal" [SYS] operation for programming purpose. For further informations please refer to the StudioX instruction notes.<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2024-04-18T06:36:43Z

Importing a new version from external source

New page

==Setup with StudioX==
You can also use the StudioX app to start receiver scan and perform further setup steps. In this case open the '''Control''' menu in StudioX and click the '''SCAN''' button in this menu's screen. Please note that when the RX line of the receiver is connected to SYS port, you must disconnect the receiver from SYS temporarily, switch off your radio and power cycle your device. It will then enable "normal" SYS operation for programming purpose. For further informations please refer to the StudioX instruction notes.<br />
<br />