Translations:Manuals:BXFbl:Radio Setup:RemoteSat/24/en - Revision history

FuzzyBot: Importing a new version from external source

2024-05-22T09:33:28Z

Importing a new version from external source

← Older revision		Revision as of 09:33, 22 May 2024
Line 3:		Line 3:
	* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).		* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
	* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.		* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
			<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2024-05-20T19:25:04Z

Importing a new version from external source

← Older revision		Revision as of 19:25, 20 May 2024
Line 1:		Line 1:
	'''MICROBEAST PLUS / NANOBEAST'''<br />		'''MICROBEAST PLUS / NANOBEAST'''<br />
	* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.		* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.
	* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).		* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
	* After successful binding procedure the receiver‘s LED will stay solid. On the ~~MICROBEAST PLUS LED '''H'''~~ will ~~flash alternating with all other LEDs for 2 seconds, then~~ the ~~device~~ will ~~restart~~. Remove the bind plug~~. If needed cycle power~~ and ~~enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above)~~.		* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
	<br />		<br />

FuzzyBot: Importing a new version from external source

2024-05-14T14:16:43Z

Importing a new version from external source

New page

'''MICROBEAST PLUS / NANOBEAST'''<br />
* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* After successful binding procedure the receiver‘s LED will stay solid. On the MICROBEAST PLUS LED '''H''' will flash alternating with all other LEDs for 2 seconds, then the device will restart. Remove the bind plug. If needed cycle power and enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above).
<br />