Translations:Manuals:BXFbl:Radio Setup:RemoteSat/25/en - Revision history

FuzzyBot: Importing a new version from external source

2024-05-30T18:39:37Z

Importing a new version from external source

← Older revision		Revision as of 18:39, 30 May 2024
Line 1:		Line 1:
	'''MICROBEAST ULTRA'''<br />		'''MICROBEAST ULTRA (v5.9.x)'''<br />
	* Insert a Spektrum® ''Bind Plug'' at the '''[AUX\|PIT\|RUD]''' port.		* Disconnect(!) the Spektrum® remote satellite and switch on the power supply.
	* Disconnect(!) the Spektrum® remote satellite		* During init sequence (LED light H-N is running) push and hold the button for 4 seconds, then release
	* To bind a DSMX satellite switch on the power supply ~~now~~. ~~The yellow~~ LED ~~'''~~A~~''' on the MICROBEAST ULTRA will start to~~ flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash ~~as well.~~ Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).		* LEDs A and H flash in alternating sequence
	* After successful binding procedure the receiver‘s LED will stay solid~~. Then the device~~ will restart and enter RECEIVER MENU if the ~~current~~ receiver ~~type is not set to DSMX or will start with init sequence. Remove the bind plug~~ and proceed.		* Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash in combination with LED A on MICROBEAST
			* Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
			* After successful binding procedure the receiver‘s LED will stay solid
			* Your MICROBEAST will restart and enter RECEIVER MENU. Press button briefly to scan for the receiver and proceed.
	<br />		<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2024-05-20T19:25:04Z

Importing a new version from external source

← Older revision		Revision as of 19:25, 20 May 2024
Line 2:		Line 2:
	* Insert a Spektrum® ''Bind Plug'' at the '''[AUX\|PIT\|RUD]''' port.		* Insert a Spektrum® ''Bind Plug'' at the '''[AUX\|PIT\|RUD]''' port.
	* Disconnect(!) the Spektrum® remote satellite		* Disconnect(!) the Spektrum® remote satellite
	* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).		* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
	* After successful binding procedure the receiver‘s LED will stay solid. ~~LED '''H'''~~ will ~~flash alternating~~ with ~~all other LEDs for 2 seconds, then MICROBEAST will restart~~. Remove the bind plug~~. If needed cycle power~~ and ~~enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above)~~.		* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
	<br />		<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2024-05-14T14:16:43Z

Importing a new version from external source

New page

'''MICROBEAST ULTRA'''<br />
* Insert a Spektrum® ''Bind Plug'' at the '''[AUX|PIT|RUD]''' port.
* Disconnect(!) the Spektrum® remote satellite
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' will flash alternating with all other LEDs for 2 seconds, then MICROBEAST will restart. Remove the bind plug. If needed cycle power and enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above).
<br />
<br />