FuzzyBot: Importing a new version from external source

2017-12-20T15:17:08Z

Importing a new version from external source

← Older revision		Revision as of 15:17, 20 December 2017
Line 1:		Line 1:
	=Adjustment on the device=		=Adjustment on the device=
	To set the gear ratio on the device you have to adjust three menu points in a row. Menu point '''F''' sets the number of gear ratio before the decimal point, menu points '''G''' and '''H''' specify the first two decimal places. Compare the following table and set the Status-LED using the rudder stick to the corresponding color and condition at each menu point so the desired gear ratio will result as a combination of all three menu points ('''X.YZ:1'''). The ratio can be adjusted in increments of 0.05. Choose the ratio that is the closest for your helicopter and set the menu points one after the other. To proceed to the each menu point briefly push the button. After menu point '''H''' the initial setup is finished and the button press will lead back to operation mode.<br />		To set the gear ratio on the device you have to adjust three menu points in a row. Menu point '''F''' sets the number of gear ratio before the decimal point, menu points '''G''' and '''H''' specify the first two decimal places. Compare the following table and set the Status-LED using the rudder stick to the corresponding color and condition at each menu point so the desired gear ratio will result as a combination of all three menu points ('''X.YZ:1'''). The ratio can be adjusted in increments of 0.05. Choose the ratio that is the closest for your helicopter and set the menu points one after the other. To proceed to the each menu point briefly push the button. After menu point '''H''' the initial setup is finished and the button press will lead back to operation mode.<br />
	~~<br />~~
	{{QUOTE\|The gear ratio should be specified in the instruction manual for your helicopter. Especially with electric models it will vary depending on the motor pinion used. For helicopters with a single-stage gear drive the reduction can be calculated by dividing the number of pinion teeth from the main gear tooth count.<br />
	~~<br />~~
	'''Example:''' Shape S8 - Main gear tooth count 130 teeth / 15 tooth pinion. Gear ratio apprx. 8.65:1. '''F''' - Status-LED purple flashing, '''G''' - Status-LED red, '''H''' - Status-LED purple.}}<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2017-12-20T15:08:42Z

Importing a new version from external source

New page

=Adjustment on the device=
To set the gear ratio on the device you have to adjust three menu points in a row. Menu point '''F''' sets the number of gear ratio before the decimal point, menu points '''G''' and '''H''' specify the first two decimal places. Compare the following table and set the Status-LED using the rudder stick to the corresponding color and condition at each menu point so the desired gear ratio will result as a combination of all three menu points ('''X.YZ:1'''). The ratio can be adjusted in increments of 0.05. Choose the ratio that is the closest for your helicopter and set the menu points one after the other. To proceed to the each menu point briefly push the button. After menu point '''H''' the initial setup is finished and the button press will lead back to operation mode. 
 
{{QUOTE|The gear ratio should be specified in the instruction manual for your helicopter. Especially with electric models it will vary depending on the motor pinion used. For helicopters with a single-stage gear drive the reduction can be calculated by dividing the number of pinion teeth from the main gear tooth count. 
 
'''Example:''' Shape S8 - Main gear tooth count 130 teeth / 15 tooth pinion. Gear ratio apprx. 8.65:1. '''F''' - Status-LED purple flashing, '''G''' - Status-LED red, '''H''' - Status-LED purple.}}

Translations:Manuals:MBPlusFblV5:Governormenu F/7/en - Revision history

FuzzyBot: Importing a new version from external source

FuzzyBot: Importing a new version from external source