Translations:Manuals:MBPlusFblV5:Setupmenu E/6/en - Revision history

FuzzyBot: Importing a new version from external source

2017-11-30T14:49:59Z

Importing a new version from external source

← Older revision		Revision as of 14:49, 30 November 2017
Line 4:		Line 4:
	2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left) reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />		2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left) reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />
	<br />		<br />
	3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when ~~reaching~~ the end position.)<br />		3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />
	<br />		<br />
	{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />		{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />
	<br />		<br />
	'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement. Here the LED will light up in '''blue''' color when you turn the helicopter to the '''right''' and light up in '''red''' when you turn it to the '''left'''. ~~This is to give~~ you a little reminder when you need to do the setup later on the field ~~and you can't rememeber what color stands for what direction~~!}}<br />		'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement. Here the LED will light up in '''blue''' color when you turn the helicopter to the '''right''' and light up in '''red''' when you turn it to the '''left'''. So you can get a little reminder when you do not know which is the correct stick direction to setup, when you need to do the setup later on the field!}}<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2017-11-30T14:36:04Z

Importing a new version from external source

← Older revision		Revision as of 14:36, 30 November 2017
Line 4:		Line 4:
	2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left) reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />		2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left) reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />
	<br />		<br />
	3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when ~~raching~~ the end position.)<br />		3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position.)<br />
	<br />		<br />
	{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />		{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />
	<br />		<br />
	'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement. Here the LED will light up in '''blue''' color when you turn the helicopter to the '''right''' and light up in '''red''' when you turn it to the '''left'''. So you ~~can get~~ a little reminder ~~when you do not know which is the correct stick direction to setup,~~ when you need to do the setup later on the field!}}<br />		'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement. Here the LED will light up in '''blue''' color when you turn the helicopter to the '''right''' and light up in '''red''' when you turn it to the '''left'''. This is to give you a little reminder when you need to do the setup later on the field and you can't rememeber what color stands for what direction!}}<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2017-11-30T10:33:18Z

Importing a new version from external source

← Older revision		Revision as of 10:33, 30 November 2017
Line 1:		Line 1:
	==SETUP MENU F - Rudder control direction==		==SETUP MENU F - Rudder control direction==
	1. Move the rudder stick and check the rudder direction on the helicopter. If the stick is moving the servo into the wrong direction~~, '''~~use the servo reverse function of your transmitter and reverse the rudder channel to set stick control direction correctly.~~'''~~<br />		1. Move the rudder stick and check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly.<br />
	<br />		<br />
	2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. When the display is inverted (red = right and blue = left)~~, '''~~reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />		2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left) reverse the display (internal control direction) by tapping the aileron(!) stick once.'''<br />
	<br />		<br />
	3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />		3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.)<br />

FuzzyBot: Importing a new version from external source

2017-11-27T16:18:10Z

Importing a new version from external source

New page

==SETUP MENU F - Rudder control direction==
1. Move the rudder stick and check the rudder direction on the helicopter. If the stick is moving the servo into the wrong direction, '''use the servo reverse function of your transmitter and reverse the rudder channel to set stick control direction correctly.''' 
 
2. Now set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick to the '''right''', the Status LED must light up or flash in '''blue''' color. When you move the rudder stick to the '''left''', the Status LED must light up or flash in '''red''' color. When the display is inverted (red = right and blue = left), '''reverse the display (internal control direction) by tapping the aileron(!) stick once.''' 
 
3. Optional: When you move the rudder stick to full deflection, the Status LED should light solid, not just flash. If this is not the case, '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position'''. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.) 
 
{{QUOTE|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter! 
 
'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement. Here the LED will light up in '''blue''' color when you turn the helicopter to the '''right''' and light up in '''red''' when you turn it to the '''left'''. So you can get a little reminder when you do not know which is the correct stick direction to setup, when you need to do the setup later on the field!}}