Translations:Manuals:MBPlusFblV5:Setupmenu E/7/en - Revision history

FuzzyBot: Importing a new version from external source

2017-11-30T14:49:50Z

Importing a new version from external source

← Older revision		Revision as of 14:49, 30 November 2017
Line 11:		Line 11:
	3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />		3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />
	<br />		<br />
	{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />		{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />
	<br />		<br />
	'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement.}}<br />		'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement.}}<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2017-11-30T10:32:50Z

Importing a new version from external source

← Older revision		Revision as of 10:32, 30 November 2017
Line 5:		Line 5:
	<br />		<br />
	<br />		<br />
	1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Move stick to max. position! Check Status LED." In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when ~~raching~~ the end position.)<br />		1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Move stick to max. position! Check Status LED." In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when reaching the end position.)<br />
	<br />		<br />
	2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above ~~and adjust~~ the servo ~~limit by changing~~ the ~~values in~~ the ~~two adjustment boxes for each~~ direction. ~~To do so, carefully use~~ the rudder stick to move the ~~servo~~ to the ~~endpoint~~ (~~watch out to not jam~~ the ~~servo~~) ~~and increase/decrease~~ the ~~endpoint as necessary~~.<br />		2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above. When you move the rudder stick check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter''' and reverse the rudder channel to set stick control direction correctly. Now when the servo is moving correctly set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you move the rudder stick to the <span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.<br />
	<br />		<br />
	3. ~~When you move the rudder stick check the rudder direction on the helicopter. '''If the stick is moving~~ the servo ~~into~~ the ~~wrong direction use the servo reverse function of your transmitter and reverse~~ the ~~rudder channel to set stick control~~ direction ~~correctly~~.~~'''<br />~~		3. Finally adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary.<br />
	~~<br />~~
	~~4. Finally set the rudder direction of the MICROBEAST PLUS gyro: When you move~~ the rudder stick~~/servo~~ to ~~the <span style="color: #4169E1;">'''right'''</span>, the Status LED must light up or flash in <span style="color: #4169E1;">'''blue'''</span> color. When you~~ move the ~~rudder stick~~ to the ~~<span style="color: #DC143C;">'''left'''</span>, the Status LED must light up or flash in <span style="color: #DC143C;">'''red'''</span> color. '''When the display is inverted~~ (~~red = right and blue = left), reverse~~ the ~~display (internal control direction~~) ~~by choosing either ''normal'' or ''inverted'' in~~ the ~~software~~.~~'''~~<br />
	<br />		<br />
	{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />		{{QUOTE\|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter!<br />

FuzzyBot: Importing a new version from external source

2017-11-27T16:16:01Z

Importing a new version from external source

New page

=Setup with StudioX=
To activate the rudder adjustments click the '''Adjust button''' in the corresponding table row (when using the '''Wizard''' function this will be done automatically when you click the '''Next button''' after adjusting Menu Point D). 
 
[[File:SetupEF.png|x250px]] 
 
 
1. When you move the rudder stick to full deflection, the Status LED on the MICROBEAST PLUS should light solid and the label ''right'' or ''left'' should change the color accordingly. If the stick is not moving far enough, you will see the message "Move stick to max. position! Check Status LED." In this case '''increase the servo throw/endpoint of the rudder channel in the transmitter just as far so that the Status LED changes from flashing to solid when the rudder stick reaches the end position''' and the label will disappear in the software. (Note: Do not increase the endpoint too much in the transmitter. We need an exact match of full stick position and stick end position. So the Status LED should just change from flashing to solid when raching the end position.) 
 
2. Now connect the rudder servo to [CH4] port of MICROBEAST PLUS as described above and adjust the servo limit by changing the values in the two adjustment boxes for each direction. To do so, carefully use the rudder stick to move the servo to the endpoint (watch out to not jam the servo) and increase/decrease the endpoint as necessary. 
 
3. When you move the rudder stick check the rudder direction on the helicopter. '''If the stick is moving the servo into the wrong direction use the servo reverse function of your transmitter and reverse the rudder channel to set stick control direction correctly.''' 
 
4. Finally set the rudder direction of the MICROBEAST PLUS gyro: When you move the rudder stick/servo to the '''right''', the Status LED must light up or flash in '''blue''' color. When you move the rudder stick to the '''left''', the Status LED must light up or flash in '''red''' color. '''When the display is inverted (red = right and blue = left), reverse the display (internal control direction) by choosing either ''normal'' or ''inverted'' in the software.''' 
 
{{QUOTE|Always set servo direction in the transmitter first, then check the display on the MICROBEAST PLUS or in the software and change the internal control direction if it does not match the real direction. '''Do not change the internal direction in order to change the servo direction! This is only used for telling the gyro in which direction it must move the servo.''' Be very conscientious when doing this setup step, as wrong gyro direction will cause loss of control during takeoff and you probably crash the helicopter! 
 
'''In addition you can check the gyro direction by turning the helicopter by hand around its vertical axis.''' When turning the heli the gyro must move the servo so that the rotor will produce a counter action agains the turn direction. So later in flight the gyro will stop the helicopter from unwanted movement.}}