FuzzyBot: Importing a new version from external source

2018-07-19T09:24:45Z

Importing a new version from external source

← Older revision		Revision as of 09:24, 19 July 2018
Line 1:		Line 1:
	=Adjustment on the device=		=Adjustment on the device=
	Initially when the trimming is 0 on all servos the Status LED will be off. Attach the servo horns on the servos at their true center position, so that you get roughly equal throws to both direction. Mount the servo horns so that they form ~~as much as possible~~ a 90 degrees angle to the linkage rod. Then in the next step you electronically fine trim every single servo‘s center position, as usually mounting the servo horn at exact 90 degrees will not work out perfectly depending on the servo‘s gear train and the servo horn.<br />		Initially when the trimming is 0 on all servos the Status LED will be off. Attach the servo horns on the servos at their true center position, so that you get roughly equal throws to both direction. Mount the servo horns so that they form a 90 degrees angle to the linkage rod as close as possible. Then in the next step you electronically fine trim every single servo‘s center position, as usually mounting the servo horn at exact 90 degrees will not work out perfectly depending on the servo‘s gear train and the servo horn.<br />
	<br />		<br />
	By tapping the aileron ~~stick~~ you can select one servo after another. Every color of the Status-LED is corresponding to a specific servo channel that is indicating its selection by a short up and down move. Use the rudder stick to change the servo trimming/adjust the center position. You can switch back and forth between the servos as often as you need.<br />		By tapping the '''stick for aileron''' you can '''select one servo after another'''. Every color of the Status-LED is corresponding to a specific servo channel that is indicating its selection by a short up and down move. Use the '''rudder stick''' to change the '''servo trimming/adjust the center position'''. You can switch back and forth between the servos as often as you need.<br />
	<br />		<br />
	{\|cellpadding="4" cellspacing="0" border="1"		{\|cellpadding="4" cellspacing="0" border="1"

FuzzyBot: Importing a new version from external source

2017-11-30T12:31:43Z

Importing a new version from external source

New page

=Adjustment on the device=
Initially when the trimming is 0 on all servos the Status LED will be off. Attach the servo horns on the servos at their true center position, so that you get roughly equal throws to both direction. Mount the servo horns so that they form as much as possible a 90 degrees angle to the linkage rod. Then in the next step you electronically fine trim every single servo‘s center position, as usually mounting the servo horn at exact 90 degrees will not work out perfectly depending on the servo‘s gear train and the servo horn. 
 
By tapping the aileron stick you can select one servo after another. Every color of the Status-LED is corresponding to a specific servo channel that is indicating its selection by a short up and down move. Use the rudder stick to change the servo trimming/adjust the center position. You can switch back and forth between the servos as often as you need. 
 
{|cellpadding="4" cellspacing="0" border="1"
| style="width:100px; text-align:left;" | '''Status-LED''' || style="text-align:center;" | '''Servo trim'''
|-
|style="color:white; background-color:black" | off || all zero
|-
| style="color:white; background-color:#CC66CC" | purple || CH1 – elevator servo
|-
|style="color:white; background-color:#FF3300" | red ||CH2 – aileron(1) servo
|-
| style="color:white; background-color:#0066FF" | blue || CH3 – aileron(2) / pitch servo (mCCPM)
|-
| style="color:white; background: linear-gradient(to right, #FF3300, black, #0066FF)" | red/blue || CH7 – elevator servo(2) (90° eCCPM only)
|}

Translations:Manuals:MBPlusFblV5:Setupmenu H/3/en - Revision history

FuzzyBot: Importing a new version from external source

FuzzyBot: Importing a new version from external source