Translations:Manuals:MBPlusFblV5:Setupmenu J/2/en - Revision history

FuzzyBot: Importing a new version from external source

2020-06-03T07:47:51Z

Importing a new version from external source

← Older revision		Revision as of 07:47, 3 June 2020
Line 1:		Line 1:
	At SETUP MENU point J we adjust the internal servo throw so that ~~the AR7210BX receiver~~ has a reference on how far it must move the servos when controlling the helicopter. To set the throw you align one rotorblade on the longitudinal axis (in parallel to the tail boom) and measure the cyclic pitch with a digital pitch gauge on this rotorblade. (You can do this from the front or from the rear!)<br />		At SETUP MENU point J we adjust the internal servo throw so that MICROBEAST Plus has a reference on how far it must move the servos when controlling the helicopter. To set the throw you align one rotorblade on the longitudinal axis (in parallel to the tail boom) and measure the cyclic pitch with a digital pitch gauge on this rotorblade. (You can do this from the front or from the rear!)<br />
	{\|		{\|
	\|-		\|-

FuzzyBot: Importing a new version from external source

2018-07-19T09:55:43Z

Importing a new version from external source

← Older revision		Revision as of 09:55, 19 July 2018
Line 1:		Line 1:
	At SETUP MENU point J we adjust the internal servo throw so that ~~MICROBEAST PLUS~~ has a reference on how far it must move the servos when controlling the helicopter. To set the throw you ~~have to~~ align one rotorblade on the longitudinal axis (in parallel to the tail boom) and measure the cyclic pitch with a digital pitch gauge on this rotorblade.<br />		At SETUP MENU point J we adjust the internal servo throw so that the AR7210BX receiver has a reference on how far it must move the servos when controlling the helicopter. To set the throw you align one rotorblade on the longitudinal axis (in parallel to the tail boom) and measure the cyclic pitch with a digital pitch gauge on this rotorblade. (You can do this from the front or from the rear!)<br />
	{\|		{\|
	\|-		\|-
Line 6:		Line 6:
	\|}<br />		\|}<br />
	<br />		<br />
	Initially you should see 0 degrees of pitch now (in case you did the setup at SETUP MENU point H ~~correctly~~!). Then you switch to the adjustment position~~, the~~ system will give some amount of pitch ~~and~~ you measure ~~the pitch~~ again. This time you should see 6.0 degrees (+ or - is not of importance). If not increase or decrease the swash throw accordingly. The color of the Status LED gives some indication whether you rotorhead geometry is well suited for flybarless usage or not. Ideally the Status LED on the device should be blue when in 6.0 degress position. If it isn't, this means your servo movements cause very much pitch deflection on the rotorhead. This can be bad for the performance as the system may tend to oversteer and overreact very easily. If you have problem with finding correct gain settings or overcompensation later in flight, the cause may be found here. To solve this you can change geometry by moving the linkage balls on the servo horns closer to the servo center.<br />		Initially you should see 0 degrees of pitch now (in case you did the setup at SETUP MENU point H properly!). Then you switch to the adjustment position. The system will give some amount of pitch which you measure again. This time you should see 6.0 degrees (+ or - is not of importance). If not, increase or decrease the swash throw accordingly.<br />
			<br />
			The color of the Status LED gives some indication whether you rotorhead geometry is well suited for flybarless usage or not. Ideally the Status LED on the device should be blue when in 6.0 degress position. If it isn't, this means your servo movements cause very much pitch deflection on the rotorhead. This can be bad for the performance as the system may tend to oversteer and overreact very easily. If you have problem with finding correct gain settings or overcompensation later in flight, the cause may be found here. To solve this you can change geometry by moving the linkage balls on the servo horns closer to the servo center.<br />
	<br />		<br />
	{\|cellpadding="4" cellspacing="0" border="1"		{\|cellpadding="4" cellspacing="0" border="1"

FuzzyBot: Importing a new version from external source

2017-11-30T13:24:51Z

Importing a new version from external source

New page

At SETUP MENU point J we adjust the internal servo throw so that MICROBEAST PLUS has a reference on how far it must move the servos when controlling the helicopter. To set the throw you have to align one rotorblade on the longitudinal axis (in parallel to the tail boom) and measure the cyclic pitch with a digital pitch gauge on this rotorblade. 
{|
|-
| [[Image:Heli_sideview.png|x120px|border]]
| [[Image:Heli_topview.png|x120px|border]]
|} 
 
Initially you should see 0 degrees of pitch now (in case you did the setup at SETUP MENU point H correctly!). Then you switch to the adjustment position, the system will give some amount of pitch and you measure the pitch again. This time you should see 6.0 degrees (+ or - is not of importance). If not increase or decrease the swash throw accordingly. The color of the Status LED gives some indication whether you rotorhead geometry is well suited for flybarless usage or not. Ideally the Status LED on the device should be blue when in 6.0 degress position. If it isn't, this means your servo movements cause very much pitch deflection on the rotorhead. This can be bad for the performance as the system may tend to oversteer and overreact very easily. If you have problem with finding correct gain settings or overcompensation later in flight, the cause may be found here. To solve this you can change geometry by moving the linkage balls on the servo horns closer to the servo center. 
 
{|cellpadding="4" cellspacing="0" border="1"
| style="width:100px; text-align:left;" | '''Status-LED''' || style="text-align:center;" | '''Cyclic throw'''
|-
| style="color:white; background-color:#CC66CC" | purple || not good
|-
|style="color:white; background-color:#FF3300" | red || OK
|-
| style="color:white; background-color:#0066FF" | blue || perfect!
|}