FuzzyBot: Importing a new version from external source

2018-07-19T10:19:20Z

Importing a new version from external source

← Older revision		Revision as of 10:19, 19 July 2018
Line 1:		Line 1:
	At SETUP MENU point L we can limit the servo movement so that ~~they~~ will not come out of the possible range of action and cause jamming of the linkages or swashplate. ~~Ideally~~ we want to limit as less as possible, so that the system can control the helicopter without any restrictions. For the ease of use, the limiting is only one value to adjust but which will affect all servos and all possible positions at once, especially when steering into the corners. So when adjusting the limit you move pitch, aileron and elevator all at once and into all possible positions and check if there is some point where the servos get jammed. ~~Then you set~~ the limit so that there is just no binding at any point.<br />		At SETUP MENU point L we can limit the servo movement so that the servos will not come out of the possible range of action and cause jamming of the linkages or swashplate. But ideally we want to limit as less as possible, so that the system can control the helicopter without any restrictions!
			<br />
			For the ease of use, the limiting is only one value to adjust but which will affect all servos and all possible positions at once, especially when steering into the corners. So when adjusting the limit, you move pitch, aileron and elevator all at once and into all possible positions and check if there is some point where the servos get jammed. Adjust the limit so that there is just no binding at any point.<br />
	<br />		<br />
	The color of the Status LED gives some indication whether you rotorhead geometry is well suited for flybarless usage or not. Ideally the Status LED on the device should be blue after you've adjusted the limit properly. If it isn't, this means your servos do not make very large deflections and probably you do not have very much cyclic pitch left in the extreme positions. This can for example cause pitching up when flying with high speed and lots of collective input, inprecise flying in general or it can cause you heli not to have equal rotations rates, accelerate slowly or not being able to reach high rotation rates at all.<br />		The color of the Status LED gives some indication whether you rotorhead geometry is well suited for flybarless usage or not. Ideally the Status LED on the device should be blue after you've adjusted the limit properly. If it isn't, this means your servos do not make very large deflections and probably you do not have very much cyclic pitch left in the extreme positions. This can for example cause pitching up when flying with high speed and lots of collective input, inprecise flying in general or it can cause you heli not to have equal rotations rates, accelerate slowly or not being able to reach high rotation rates at all.<br />

FuzzyBot: Importing a new version from external source

2017-11-30T14:11:25Z

Importing a new version from external source

New page

At SETUP MENU point L we can limit the servo movement so that they will not come out of the possible range of action and cause jamming of the linkages or swashplate. Ideally we want to limit as less as possible, so that the system can control the helicopter without any restrictions. For the ease of use, the limiting is only one value to adjust but which will affect all servos and all possible positions at once, especially when steering into the corners. So when adjusting the limit you move pitch, aileron and elevator all at once and into all possible positions and check if there is some point where the servos get jammed. Then you set the limit so that there is just no binding at any point. 
 
The color of the Status LED gives some indication whether you rotorhead geometry is well suited for flybarless usage or not. Ideally the Status LED on the device should be blue after you've adjusted the limit properly. If it isn't, this means your servos do not make very large deflections and probably you do not have very much cyclic pitch left in the extreme positions. This can for example cause pitching up when flying with high speed and lots of collective input, inprecise flying in general or it can cause you heli not to have equal rotations rates, accelerate slowly or not being able to reach high rotation rates at all. 
 
{|cellpadding="4" cellspacing="0" border="1"
| style="width:100px; text-align:left;" | '''Status-LED''' || style="text-align:center;" | '''Servo limit'''
|-
| style="color:white; background-color:#CC66CC" | purple || not good
|-
|style="color:white; background-color:#FF3300" | red || OK
|-
| style="color:white; background-color:#0066FF" | blue || perfect!
|}

Translations:Manuals:MBPlusFblV5:Setupmenu L/2/en - Revision history

FuzzyBot: Importing a new version from external source

FuzzyBot: Importing a new version from external source