FuzzyBot: Importing a new version from external source

2022-03-30T08:24:09Z

Importing a new version from external source

← Older revision		Revision as of 08:24, 30 March 2022
Line 1:		Line 1:
	==Button control==		==Button control==
	Proceed step by step through the different menu points reaching from A to N and perform the basic adjustment as described in the following. By briefly pushing the button at each step you will save the current setting and proceed to the next step. To leave the SETUP MENU you have to go through all menu points. After pushing the button at the last menu point ~~(depending~~ on installed firmware features and receiver type ~~this~~ either ~~can~~ be [[Manuals:MBPlusFblV52:Setupmenu_M\|SETUP MENU point M]] or [[Manuals:MBPlusFblV52:Setupmenu_N\|N]] or [[Manuals:MBPlusFblV52:Governormenu_F\|GOVERNOR MENU point F]] or [[Manuals:MBPlusFblV52:Governormenu_F\|H]]) ~~you will exit the SETUP MENU and the system is ready for operation again.~~<br />		Proceed step by step through the different menu points reaching from A to N and perform the basic adjustment as described in the following. By briefly pushing the button at each step you will save the current setting and proceed to the next step.<br />
			<br />
			To leave the SETUP MENU you have to go through all menu points! After pushing the button at the last menu point you will exit the SETUP MENU and the system is ready for operation again. Depending on installed firmware features and receiver type the last point can either be [[Manuals:MBPlusFblV52:Setupmenu_M\|SETUP MENU point M]] or [[Manuals:MBPlusFblV52:Setupmenu_N\|N]] or [[Manuals:MBPlusFblV52:Governormenu_F\|GOVERNOR MENU point F]] or [[Manuals:MBPlusFblV52:Governormenu_F\|H]]) <br />
	<br />		<br />
	[[Image:Menuskip.png\|x150px\|none]]		[[Image:Menuskip.png\|x150px\|none]]
Line 6:		Line 8:
	<p>		<p>
	If you need to change some specific setting later onwards you can enter the SETUP MENU again as described above and skip menu points by only pressing the button without changing anything at these points. So you can navigate to the desired menu point by simply pressing the button several times until you reach this point. Then after you have finished the adjustment, again press the button repeatedly to proceed to the end of the menu and to get back into operation mode.</p>		If you need to change some specific setting later onwards you can enter the SETUP MENU again as described above and skip menu points by only pressing the button without changing anything at these points. So you can navigate to the desired menu point by simply pressing the button several times until you reach this point. Then after you have finished the adjustment, again press the button repeatedly to proceed to the end of the menu and to get back into operation mode.</p>
	* In operation mode no MENU LED is glowing!		<br />
	* Just for your info at this step: There is another menu called PARAMETER MENU. This is entered by just briefly pressing the button from operation mode. Here the Menu LEDs are flashing quickly. If you see this condition you've entered the wrong menu. Skip through the menu by repeatedly pressing the button until back in operation mode and then retry to enter SETUP MENU, this time holding the button longer so that Menu LED A lights solid!<br />		{{WARNING_QUOTE\|'''Never fly while MICROBEAST PLUS is in SETUP MENU or any other menu!''' In this condition the gyro control and the stick controls are disabled. In operation mode no MENU LED is glowing!}}<br />
			Just for your info at this step: There is another menu called PARAMETER MENU. This is entered by just briefly pressing the button from operation mode. Here the Menu LEDs are flashing quickly. If you see this condition you've entered the wrong menu. Skip through the menu by repeatedly pressing the button until back in operation mode and then retry to enter SETUP MENU, this time holding the button longer so that Menu LED A lights solid!<br />
	<br />		<br />

FuzzyBot: Importing a new version from external source

2020-10-20T13:02:13Z

Importing a new version from external source

New page

==Button control==
Proceed step by step through the different menu points reaching from A to N and perform the basic adjustment as described in the following. By briefly pushing the button at each step you will save the current setting and proceed to the next step. To leave the SETUP MENU you have to go through all menu points. After pushing the button at the last menu point (depending on installed firmware features and receiver type this either can be [[Manuals:MBPlusFblV52:Setupmenu_M|SETUP MENU point M]] or [[Manuals:MBPlusFblV52:Setupmenu_N|N]] or [[Manuals:MBPlusFblV52:Governormenu_F|GOVERNOR MENU point F]] or [[Manuals:MBPlusFblV52:Governormenu_F|H]]) you will exit the SETUP MENU and the system is ready for operation again. 
 
[[Image:Menuskip.png|x150px|none]]
 

If you need to change some specific setting later onwards you can enter the SETUP MENU again as described above and skip menu points by only pressing the button without changing anything at these points. So you can navigate to the desired menu point by simply pressing the button several times until you reach this point. Then after you have finished the adjustment, again press the button repeatedly to proceed to the end of the menu and to get back into operation mode.
* In operation mode no MENU LED is glowing!
* Just for your info at this step: There is another menu called PARAMETER MENU. This is entered by just briefly pressing the button from operation mode. Here the Menu LEDs are flashing quickly. If you see this condition you've entered the wrong menu. Skip through the menu by repeatedly pressing the button until back in operation mode and then retry to enter SETUP MENU, this time holding the button longer so that Menu LED A lights solid!

Translations:Manuals:MBPlusFblV52:Setupmenu intro/4/en - Revision history

FuzzyBot: Importing a new version from external source

FuzzyBot: Importing a new version from external source