Translations:Manuals:MBUltraFblV5:Radio Setup/4/en - Revision history

FuzzyBot: Importing a new version from external source

2023-11-06T10:37:20Z

Importing a new version from external source

← Older revision		Revision as of 10:37, 6 November 2023
Line 1:		Line 1:
	~~'''Binding~~ procedure ~~for~~ Spektrum® ~~remote satellites'''~~		=Bind procedure Spektrum® DSMX satellite=
	<p>		<p>
	* Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST ULTRA.		* Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST ULTRA.
Line 11:		Line 11:
	<br />		<br />
	After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' respectively '''N''' flash alternately to all other LEDs for 2 seconds, then MICROBEAST ULTRA will restart. Cycle power and enter receiver setup menu as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.</p>		After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' respectively '''N''' flash alternately to all other LEDs for 2 seconds, then MICROBEAST ULTRA will restart. Cycle power and enter receiver setup menu as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.</p>
	~~{\|cellspacing="20"~~
	~~\|[[File:Spektrum_bind_v5.png\|x400px]]~~
	\|}
	<p>		<p>
	'''Note:'''		'''Note:'''

FuzzyBot: Importing a new version from external source

2023-02-28T09:22:07Z

Importing a new version from external source

← Older revision		Revision as of 09:22, 28 February 2023
Line 2:		Line 2:
	<p>		<p>
	* Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST ULTRA.		* Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST ULTRA.
	* Disconnect(!) the Spektrum® remote satellite.		* Disconnect(!) the Spektrum® remote satellite (this is different to previous MICROBEAST and MICROBEAST PLUS devices!)
	* In case the power is supplied exclusively at the [SYS] connection, to bind a Spektrum® satellite receiver the power supply must be provided temporarily through any of the other ports [CH1] - [CH5].<br />		* In case the power is supplied exclusively at the [SYS] connection, to bind a Spektrum® satellite receiver the power supply must be provided temporarily through any of the other ports [CH1] - [CH5].<br />
	<br />		<br />
	{{WARNING_QUOTE\|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}}~~<br />~~		{{WARNING_QUOTE\|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}}
	<br />		<br />
	To bind a '''DSMX''' satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).<br />		* To bind a '''DSMX''' satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).<br />
	~~<br />~~		* To select and bind a '''DSM2''' satellite, hold down the button on MICROBEAST ULTRA while switching on the power supply. Here the LED '''N''' on the MICROBEAST ULTRA will flash. Release the button and connect your receiver. Bind the receiver with your transmitter.<br />
	~~<br />~~
	To select and bind a '''DSM2''' satellite, hold down the button on MICROBEAST ULTRA while switching on the power supply. Here the LED '''N''' on the MICROBEAST ULTRA will flash. Release the button and connect your receiver. Bind the receiver with your transmitter.<br />
	<br />		<br />
	After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' respectively '''N''' flash alternately to all other LEDs for 2 seconds, then MICROBEAST ULTRA will restart. Cycle power and enter receiver setup menu as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.</p>		After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' respectively '''N''' flash alternately to all other LEDs for 2 seconds, then MICROBEAST ULTRA will restart. Cycle power and enter receiver setup menu as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.</p>

FuzzyBot: Importing a new version from external source

2023-02-27T14:59:58Z

Importing a new version from external source

New page

'''Binding procedure for Spektrum® remote satellites'''

* Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST ULTRA.
* Disconnect(!) the Spektrum® remote satellite.
* In case the power is supplied exclusively at the [SYS] connection, to bind a Spektrum® satellite receiver the power supply must be provided temporarily through any of the other ports [CH1] - [CH5]. 
 
{{WARNING_QUOTE|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}} 
 
To bind a '''DSMX''' satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system). 
 
 
To select and bind a '''DSM2''' satellite, hold down the button on MICROBEAST ULTRA while switching on the power supply. Here the LED '''N''' on the MICROBEAST ULTRA will flash. Release the button and connect your receiver. Bind the receiver with your transmitter. 
 
After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' respectively '''N''' flash alternately to all other LEDs for 2 seconds, then MICROBEAST ULTRA will restart. Cycle power and enter receiver setup menu as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.
{|cellspacing="20"
|[[File:Spektrum_bind_v5.png|x400px]]
|}

'''Note:'''
* Check carefully what type of receiver you have and what type you setup. You can bind DSMX satellites as "DSM2", which is wrong! An incorrect setting is not obvious but will lead to malfunction or failure of the radio link later in use.
* It makes no difference if you pull off the “Bind Plug” during the binding process or leave it connected as you would expect from some “standard” Spektrum® receivers!