FuzzyBot: Importing a new version from external source

2016-07-26T13:58:21Z

Importing a new version from external source

← Older revision		Revision as of 13:58, 26 July 2016
Line 1:		Line 1:
	{{DISPLAYTITLE: Usage of RPM Governor (optional)\|noerror}}		{{DISPLAYTITLE: Usage of RPM Governor (optional)\|noerror}}
	{{TOC_MBPlus}}		{{TOC_MBPlus}}
	~~{{QUOTE\|~~Please note that the RPM Governor function is an optional feature and may not be accessible on all MICROBEAST PLUS devices.<br />		<b>Please note that the RPM Governor function is an optional feature and may not be accessible on all MICROBEAST PLUS devices.</b><br />
	<br />		<br />
	[[FILE:Warning.png\|sub\|18px]] In general the RPM Governor can only be switched on when MICROBEAST PLUS is ready for operation. ~~During the initialization phase the signal from~~ the throttle ~~channel is passed directly~~ to the throttle ~~servo. Therefore~~ (~~especially with electric models~~) ~~make sure that during~~ the ~~initialization~~ the throttle ~~channel is set~~ to ~~„motor off“~~ position at ~~the transmitter~~ (~~not „Autorotation“!~~).<br />		{{QUOTE\|[[FILE:Warning.png\|sub\|18px]] When using the governor function for nitro helicopters, during the initialization phase the signal from the throttle channel is passed directly to the throttle servo. When using the governor function for electric helicopters, the throttle is held either at low throttle position or at failsafe position, depending on which position is the lowest (firmware version 4.1.x or higher). In general the RPM Governor can only be switched on when MICROBEAST PLUS is ready for operation. Additionaly you must move the throttle to the low throttle position (or lower) once after initialization phase, in order to unlock the governor.<br />
			<br />
			[[FILE:Warning.png\|sub\|18px]] If you need to move the throttle to full throttle position right after power up, i.e. to program your motor speed controller in electric governor mode, you must deactivate the RPM governor function temporarily at [[Manuals:MB_Plus:Setupmenu_N/en\|Setup menu point '''N''']] (firmware version 4.1.x or higher).<br />
	<br />		<br />
	[[FILE:Warning.png\|sub\|18px]] Note that if your receiver does not send a valid control signal to MICROBEAST PLUS within two seconds after power up, the throttle channel will be locked for security reasons. In this case [CH5] output will be set to motor failsafe position (set at Receiver menu point N). Only when MICROBEAST PLUS gets a valid signal from the receiver and the throttle stick is moved to the programmed failsafe position (or below) the throttle channel will be unlocked.<br />		[[FILE:Warning.png\|sub\|18px]] Note that if your receiver does not send a valid control signal to MICROBEAST PLUS within two seconds after power up, the throttle channel will be locked for security reasons. In this case [CH5] output will be set to motor failsafe position (set at Receiver menu point N). Only when MICROBEAST PLUS gets a valid signal from the receiver and the throttle stick is moved to the programmed failsafe position (or below) the throttle channel will be unlocked.<br />

FuzzyBot: Importing a new version from external source

2015-05-26T14:05:58Z

Importing a new version from external source

New page

{{DISPLAYTITLE: Usage of RPM Governor (optional)|noerror}}
{{TOC_MBPlus}}
{{QUOTE|Please note that the RPM Governor function is an optional feature and may not be accessible on all MICROBEAST PLUS devices. 
 
[[FILE:Warning.png|sub|18px]] In general the RPM Governor can only be switched on when MICROBEAST PLUS is ready for operation. During the initialization phase the signal from the throttle channel is passed directly to the throttle servo. Therefore (especially with electric models) make sure that during the initialization the throttle channel is set to „motor off“ position at the transmitter (not „Autorotation“!). 
 
[[FILE:Warning.png|sub|18px]] Note that if your receiver does not send a valid control signal to MICROBEAST PLUS within two seconds after power up, the throttle channel will be locked for security reasons. In this case [CH5] output will be set to motor failsafe position (set at Receiver menu point N). Only when MICROBEAST PLUS gets a valid signal from the receiver and the throttle stick is moved to the programmed failsafe position (or below) the throttle channel will be unlocked. 
 
[[FILE:Warning.png|sub|18px]] With nitro helicopters always ensure that the RPM Governor is disabled when you start the model. Otherwise the RPM Governor would drive the throttle servo up to the full throttle position and stay there as it tries to reach the demanded head speed. So always check the throttle servo position before starting the engine very carefully!}}

Translations:Manuals:MB Plus:Governor usage/1/en - Revision history

FuzzyBot: Importing a new version from external source

FuzzyBot: Importing a new version from external source