Translations:Manuals:MB Plus:Setupmenu N/2/en - Revision history

FuzzyBot: Importing a new version from external source

2015-05-29T12:45:01Z

Importing a new version from external source

← Older revision		Revision as of 12:45, 29 May 2015
Line 1:		Line 1:
	At Setup menu point '''N''' you can choose between three different options:		At Setup menu point '''N''' you can choose between three different options:
	* '''no governor''' - the RPM Governor is not used. All control commands on the throttle channel will be passed to [CH5] output directly.		* '''no governor''' - the RPM Governor is not used. All control commands on the throttle channel will be passed to [CH5] output directly.
	* '''electric governor''' - select this option if your helicopter is powered by an electric motor and an electric speed controller is plugged into [CH5] output of MICROBEAST PLUS. MICROBEAST PLUS reads the rpm signal from the speed controller or a phase sensor and controls the rotor speed accordingly. Note that the controller itself must not be operated in a (heli specific) governor mode. The speed controller must process the incomming throttle signals and control the motor as direct and unfiltered as possible ~~(see chapter 2)~~.		* '''electric governor''' - select this option if your helicopter is powered by an electric motor and an electric speed controller is plugged into [CH5] output of MICROBEAST PLUS. MICROBEAST PLUS reads the rpm signal from the speed controller or a phase sensor and controls the rotor speed accordingly. Note that the controller itself must not be operated in a (heli specific) governor mode. The speed controller must process the incomming throttle signals and control the motor as direct and unfiltered as possible.
	* '''nitro governor''' - with this option MICROBEAST PLUS can govern the rotor rpm of a helicopter with nitro or gas engine. For this MICROBEAST PLUS controls the throttle servo which is connected to [CH5] output and that controls the carburetor of the engine. The motor rpm will be read from a magnetic or optical sensor that captures the rpm from the crankshaft of the motor, the clutch bell or the main gear.		* '''nitro governor''' - with this option MICROBEAST PLUS can govern the rotor rpm of a helicopter with nitro or gas engine. For this MICROBEAST PLUS controls the throttle servo which is connected to [CH5] output and that controls the carburetor of the engine. The motor rpm will be read from a magnetic or optical sensor that captures the rpm from the crankshaft of the motor, the clutch bell or the main gear.
	<br />		<br />
Line 19:		Line 19:
	<br />		<br />
	----		----
	If the RPM Governor is deactivated (option '''no governor''') MICROBEAST PLUS will exit the Setup menu if you briefly press the button. Otherwise pressing the button will lead to [[Manuals:MB_Plus:Governormenu_A\|Governor menu point '''A''']]!		If the RPM Governor is deactivated (option '''no governor''') MICROBEAST PLUS will exit the Setup menu if you briefly press the button. Otherwise pressing the button will lead to [[Manuals:MB_Plus:Governormenu_A\|Governor menu point '''A''']] (after Menu LED '''N''' now Menu LED '''A''' will flash)!
	----		----

FuzzyBot: Importing a new version from external source

2015-05-28T14:58:05Z

Importing a new version from external source

← Older revision		Revision as of 14:58, 28 May 2015
Line 17:		Line 17:
	\|nitro		\|nitro
	\|}<br />		\|}<br />
	If the RPM Governor is deactivated (option "no governor") MICROBEAST PLUS will exit the Setup menu if you briefly press the button. Otherwise pressing the button will lead to [[Manuals:MB_Plus:Governormenu_A\|Governor menu point '''A''']]!		<br />
			----
			If the RPM Governor is deactivated (option '''no governor''') MICROBEAST PLUS will exit the Setup menu if you briefly press the button. Otherwise pressing the button will lead to [[Manuals:MB_Plus:Governormenu_A\|Governor menu point '''A''']]!
			----

FuzzyBot: Importing a new version from external source

2015-05-12T13:16:57Z

Importing a new version from external source

New page

At Setup menu point '''N''' you can choose between three different options:
* '''no governor''' - the RPM Governor is not used. All control commands on the throttle channel will be passed to [CH5] output directly.
* '''electric governor''' - select this option if your helicopter is powered by an electric motor and an electric speed controller is plugged into [CH5] output of MICROBEAST PLUS. MICROBEAST PLUS reads the rpm signal from the speed controller or a phase sensor and controls the rotor speed accordingly. Note that the controller itself must not be operated in a (heli specific) governor mode. The speed controller must process the incomming throttle signals and control the motor as direct and unfiltered as possible (see chapter 2).
* '''nitro governor''' - with this option MICROBEAST PLUS can govern the rotor rpm of a helicopter with nitro or gas engine. For this MICROBEAST PLUS controls the throttle servo which is connected to [CH5] output and that controls the carburetor of the engine. The motor rpm will be read from a magnetic or optical sensor that captures the rpm from the crankshaft of the motor, the clutch bell or the main gear.
<br />
The choice is done by moving the rudder stick in one direction until the LED indicates the desired color and state.<br />
{|cellpadding="4" cellspacing="0" border="1"
!style="width:100px; text-align:left"|Status-LED !! Governor mode
|-
|style="color:white; background-color:black"|off
|no governor
|-
|style="color:white; background-color:#FF3300"{{!}}red
|electric
|-
|style="color:white; background-color:#0066FF"{{!}}blue
|nitro
|}<br />
If the RPM Governor is deactivated (option "no governor") MICROBEAST PLUS will exit the Setup menu if you briefly press the button. Otherwise pressing the button will lead to [[Manuals:MB_Plus:Governormenu_A|Governor menu point '''A''']]!