Translations:The BEASTX servo list/1/en - Revision history

FuzzyBot: Importing a new version from external source

2015-05-04T08:35:38Z

Importing a new version from external source

← Older revision		Revision as of 08:35, 4 May 2015
Line 1:		Line 1:
	Here you find a list of servo specifications so you can see what you have to adjust at MICROBEAST Setup menu points B,C and D. Please note that not all of these specifications have been tested and validated by BEASTX. Some have been directly taken from the manufacturer recommendations in accordance with the maximum specified frequency.<br />		Here you find a list of servo specifications so you can see what you have to adjust at MICROBEAST Setup menu points B,C and D. Please note that not all of these specifications have been tested and validated by BEASTX. Some have been directly taken from the manufacturer recommendations in accordance with the maximum specified frequency.<br />
	<br />		<br />
	~~In relation to servo frequency note~~ that the servos may overheat and get damaged if the frequency is set to high.		{{QUOTE\|[[Image:Warning.png\|18px\|sub]] '''Note that the servos may overheat and get damaged if the frequency is set to high!''' Depending on height of supply voltage, servo load, vibration level and other factors it can happen that practically the frequency must not be set as high as "written on the paper". When a frequency is not "supported" by MICROBEAST/MICROBEAST PLUS simply use the lower frequency that is closest.}}
	Depending on height of supply voltage, servo load, vibration level and other factors it can happen that practically
	the frequency must not be set as high as "written on the paper". When a frequency is not "supported" by MICROBEAST/
	MICROBEAST PLUS simply use the lower frequency that is closest.
	<br />		<br />

FuzzyBot: Importing a new version from external source

2015-03-02T10:44:03Z

Importing a new version from external source

← Older revision		Revision as of 10:44, 2 March 2015
Line 5:		Line 5:
	the frequency must not be set as high as "written on the paper". When a frequency is not "supported" by MICROBEAST/		the frequency must not be set as high as "written on the paper". When a frequency is not "supported" by MICROBEAST/
	MICROBEAST PLUS simply use the lower frequency that is closest.		MICROBEAST PLUS simply use the lower frequency that is closest.
	~~<br />~~
	<br />		<br />

FuzzyBot: Importing a new version from external source

2015-03-02T09:56:41Z

Importing a new version from external source

← Older revision		Revision as of 09:56, 2 March 2015
Line 1:		Line 1:
	Here you find a list of servo specifications so you can see what you have to adjust at MICROBEAST Setup menu points B,C and D. Please note that not all of these specifications have been tested and validated by BEASTX. Some have been directly taken from the manufacturer recommendations in accordance with the maximum specified frequency.<br /> <br />		Here you find a list of servo specifications so you can see what you have to adjust at MICROBEAST Setup menu points B,C and D. Please note that not all of these specifications have been tested and validated by BEASTX. Some have been directly taken from the manufacturer recommendations in accordance with the maximum specified frequency.<br />
	In relation to servo frequency note that the servos may overheat and get damaged if the frequency is set to high. Depending on height of supply voltage, servo load, vibration level and other factors it can happen that practically the frequency must not be set as high as "written on the paper". When a frequency is not "supported" by MICROBEAST/ MICROBEAST PLUS simply use the lower frequency that is closest.		<br />
			In relation to servo frequency note that the servos may overheat and get damaged if the frequency is set to high.
			Depending on height of supply voltage, servo load, vibration level and other factors it can happen that practically
			the frequency must not be set as high as "written on the paper". When a frequency is not "supported" by MICROBEAST/
			MICROBEAST PLUS simply use the lower frequency that is closest.
	<br />		<br />
	<br />		<br />

Shornstein at 09:50, 2 March 2015

2015-03-02T09:50:45Z

← Older revision	Revision as of 09:50, 2 March 2015
Line 1:	Line 1:
		Here you find a list of servo specifications so you can see what you have to adjust at MICROBEAST Setup menu points B,C and D. Please note that not all of these specifications have been tested and validated by BEASTX. Some have been directly taken from the manufacturer recommendations in accordance with the maximum specified frequency.<br /> <br />
		In relation to servo frequency note that the servos may overheat and get damaged if the frequency is set to high. Depending on height of supply voltage, servo load, vibration level and other factors it can happen that practically the frequency must not be set as high as "written on the paper". When a frequency is not "supported" by MICROBEAST/ MICROBEAST PLUS simply use the lower frequency that is closest.
		<br />
		<br />

FuzzyBot: Importing a new version from external source

2015-03-02T09:35:01Z

Importing a new version from external source

Show changes

Shornstein at 18:30, 12 February 2015

2015-02-12T18:30:07Z

← Older revision		Revision as of 18:30, 12 February 2015
Line 6:		Line 6:
	<br />		<br />
	<br />		<br />
	<		<

Shornstein at 18:28, 12 February 2015

2015-02-12T18:28:16Z

Show changes

FuzzyBot: Importing a new version from external source

2015-02-12T18:06:11Z

Importing a new version from external source

New page