Revision as of 14:40, 2 March 2023
Information about message (contribute ) This message has no documentation.
If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Manuals:MBUltraFblV5:Receiver A )
=Adjustment on the device= To get into the RECEIVER MENU press the button on MICROBEAST ULTRA and hold it down before(!) and while turning on the receiver power supply. The yellow Menu LEDs start to cycle immediately. When you release the button, Menu LED '''A''' will be flashing and the color of the Status LED will indicate the receiver type that is selected at the moment.<br /> <br /> [[File:Receiver_setup_1.png|x180px|none]]<br /> <br /> In order to detect the receiver you're using, make sure the receiver is connected properly, bound to the radio and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBUltraFblV5:Radio_System/en|Radio System]]. Then briefly press the button to start automatic receiver detection routine. The Status LED will indicate the scan process:<br /> <br /> {|cellpadding="4" cellspacing="0" border="1" !style="width:100px; text-align:left;" | Status-LED !! Receiver type/protocol |- |style="color:white; background-color:black"{{!}}off |Standard receiver |- |style="color:white; background-color:#CC66CC"{{!}}purple |Receiver at remote port |- |style="color:white; background-color:#FF3300"{{!}}red |No receiver detected |- |style="color:white; background-color:#0066FF"{{!}}blue |Receiver at port IO1 |}<br /> * In case a single-line receiver is used, the system will skip to Menu Point '''B''' when a valid input signal was detected. * When a Standard receiver is used, the system will exit and restart immediately. * When detection fails, the system will stay at Menu Point '''A''' and the Status LED will flash in red color. Once again, make sure your receiver is connected properly to MICROBEAST ULTRA, make sure the receiver is bound to the transmitter and sending out control signals. Then please try again.<br /> {{NL}}
=Adjustment on the device=
To get into the RECEIVER MENU press the button on MICROBEAST ULTRA and hold it down before(!) and while turning on the receiver power supply. The yellow Menu LEDs start to cycle immediately. When you release the button, Menu LED '''A''' will be flashing and the color of the Status LED will indicate the receiver type that is selected at the moment.<br />
<br />
[[File:Receiver_setup_1.png|x180px|none]]<br />
<br />
In order to detect the receiver you're using, make sure the receiver is connected properly, bound to the radio and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBUltraFblV5:Radio_System/en|Radio System]]. Then briefly press the button to start automatic receiver detection routine. The Status LED will indicate the scan process:<br />
<br />
{|cellpadding="4" cellspacing="0" border="1"
!style="width:100px; text-align:left;" | Status-LED !! Receiver type/protocol
|-
|style="color:white; background-color:black"{{!}}off
|Standard receiver
|-
|style="color:white; background-color:#CC66CC"{{!}}purple
|Receiver at remote port
|-
|style="color:white; background-color:#FF3300"{{!}}red
|No receiver detected
|-
|style="color:white; background-color:#0066FF"{{!}}blue
|Receiver at port IO1
|}<br />
* In case a single-line receiver is used, the system will skip to Menu Point '''B''' when a valid input signal was detected.
* When a Standard receiver is used, the system will exit and restart immediately.
* When detection fails, the system will stay at Menu Point '''A''' and the Status LED will flash in red color. Once again, make sure your receiver is connected properly to MICROBEAST ULTRA, make sure the receiver is bound to the transmitter and sending out control signals. Then please try again.<br />
{{NL}}
Translation =Adjustment on the device= To get into the RECEIVER MENU press the button on MICROBEAST ULTRA and hold it down before(!) and while turning on the receiver power supply. The yellow Menu LEDs start to cycle immediately. When you release the button, Menu LED '''A''' will be flashing and the color of the Status LED will indicate the receiver type that is selected at the moment.<br /> <br /> [[File:Receiver_setup_1.png|x180px|none]]<br /> <br /> In order to detect the receiver you're using, make sure the receiver is connected properly, bound to the radio and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter [[Manuals:MBULTRAFblV52:Radio_System/en|Radio System]]. Then briefly press the button to start automatic receiver detection routine. The Status LED will indicate the scan process:<br /> <br /> {|cellpadding="4" cellspacing="0" border="1" !style="width:100px; text-align:left;" | Status-LED !! Receiver type/protocol |- |style="color:white; background-color:black"{{!}}off |Standard receiver |- |style="color:white; background-color:#CC66CC"{{!}}purple |Receiver at remote port |- |style="color:white; background-color:#FF3300"{{!}}red |No receiver detected |- |style="color:white; background-color:#0066FF"{{!}}blue |Receiver at port IO1 |}<br /> * In case a single-line receiver is used, the system will skip to Menu Point '''B''' when a valid input signal was detected. * When a Standard receiver is used, the system will exit and restart immediately. * When detection fails, the system will stay at Menu Point '''A''' and the Status LED will flash in red color. Once again, make sure your receiver is connected properly to MICROBEAST ULTRA, make sure the receiver is bound to the transmitter and sending out control signals. Then please try again.<br /> {{NL}} Adjustment on the device
To get into the RECEIVER MENU press the button on MICROBEAST ULTRA and hold it down before(!) and while turning on the receiver power supply. The yellow Menu LEDs start to cycle immediately. When you release the button, Menu LED A will be flashing and the color of the Status LED will indicate the receiver type that is selected at the moment.
In order to detect the receiver you're using, make sure the receiver is connected properly, bound to the radio and sending out signals. Also make sure the transmitter is setup correctly as shown in the chapter Radio System . Then briefly press the button to start automatic receiver detection routine. The Status LED will indicate the scan process:
Status-LED
Receiver type/protocol
off
Standard receiver
purple
Receiver at remote port
red
No receiver detected
blue
Receiver at port IO1
In case a single-line receiver is used, the system will skip to Menu Point B when a valid input signal was detected.
When a Standard receiver is used, the system will exit and restart immediately.
When detection fails, the system will stay at Menu Point A and the Status LED will flash in red color. Once again, make sure your receiver is connected properly to MICROBEAST ULTRA, make sure the receiver is bound to the transmitter and sending out control signals. Then please try again.