Bureaucrats, Administrators, translate-proofr
15,683
edits
Changes
Jump to navigation
Jump to search
Line 15:
Line 15: + + − + Line 34:
Line 36: − + − <br /> − − <!--T:15--> − '''Futaba® SBus2 telemetry'''<br /> − When using a receiver with Futaba SBUS2 protocol you can choose at menu point '''K''' which type of receiver you're using. As SBus2 uses different timings for the telemetry back link it is necessary to setup this manually here. To select the receiver type, move the rudder stick repeatedly in one direction until the Status LED lights in the correct color:<br /> − <br /> − {|- cellpadding="4" cellspacing="0" border="1" − |- style="width:100px; text-align:left;" − ! Status-LED !! SBUS2 telemetry − |- − |style="color:white; background-color:#000000" | off − | FASSTEST receiver − |- − |style="color:white; background-color:#FF3300" | red − | T-FHSS receiver R300x series − |- − |style="color:white; background-color:#0066FF" | blue − | T-FHSS receiver R310x series − |}<br /> Line 90:
Line 73: − + Line 97:
Line 80: + + + Line 124:
Line 110: − + Line 132:
Line 118: − + + Line 171:
Line 158: + + + + + + +
Manuals:MBUltraFblV5:Receiver M (view source)
Revision as of 08:14, 12 September 2023
, 8 months agono edit summary
* Kontronik® JIVE/PowerJIVE/HeliJIVE
* Kontronik® JIVE/PowerJIVE/HeliJIVE
* Kontronik® JIVE Pro/Kosmik
* Kontronik® JIVE Pro/Kosmik
* YGE® ESC with Texy protocol
* OMP 65A ESC that is included with OMP M4 heli
* Scorpion® Tribunus II ("UnSc" mode)
* Scorpion® Tribunus II ("UnSc" mode)
* Spektrum Avian ESC (connected at [SYS] port)
* Spektrum® Avian ESC (connected at [SYS] port)
* Speed sensor (connected at [RPM] input)<br />
* Speed sensor (connected at [RPM] input)<br />
<br />
<br />
=Adjustment on the device= <!--T:6-->
=Adjustment on the device= <!--T:6-->
In case you're using a receiver with telemetry capability, you can change the telemetry parameters at menu points '''K''', '''L''' and '''M'''. If needed, you can directly skip to these parameters without scanning receiver type and assigning functions at RECEIVER MENU points '''A''' and '''B''' by pushing and holding the button for at least 2 seconds at menu points '''A''' or '''B'''.<br />
In case you're using a receiver with telemetry capability, you can change the telemetry parameters at menu points '''L''' and '''M'''. If needed, you can directly skip to these parameters without scanning receiver type and assigning functions at RECEIVER MENU points '''A''' and '''B''' by pushing and holding the button for at least 2 seconds at menu points '''A''' or '''B'''.<br />
<br />
<br />
|-
|-
|style="color:white; background-color:#CC66CC" | purple
|style="color:white; background-color:#CC66CC" | purple
| Hobbywing® Platinum V5
| Hobbywing® Platinum V5 / OMP 65A ESC
|-
|-
|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" | red flashing
|style="color:white; background: linear-gradient(to right, #FF3300, black, #FF3300)" | red flashing
|style="color:white; background-color:#FF3300" | red
|style="color:white; background-color:#FF3300" | red
| Kontronik® JIVE Pro/Kosmik
| Kontronik® JIVE Pro/Kosmik
|-
|style="color:white; background: linear-gradient(to right, #0066FF, black, #0066FF)" | blue flashing
| YGE® Texy
|-
|-
|style="color:white; background-color:#0066FF" | blue
|style="color:white; background-color:#0066FF" | blue
==Hobbywing® Platinum (V4/V5)== <!--T:9-->
==Hobbywing® Platinum (V4/V5)== <!--T:9-->
Connect the control wire of your Hobbywing® ESC to port [IO1]. Connect the programming port of your Hobbywing® ESC to port [IO3] using a standard servo wire with male servo plugs on each end.<br />
Connect the control wire of your Hobbywing® ESC to port [IO1]. Connect the programming port of your Hobbywing® ESC to port [IO2] using a standard servo wire with male servo plugs on each end.<br />
<br />
<br />
If needed you can connect the yellow wire for measuring the motor speed to the RPM input at MICROBEAST ULTRA. The motor speed signal can be used for the internal governor function of MICROBEAST ULTRA. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />
If needed you can connect the yellow wire for measuring the motor speed to the RPM input at MICROBEAST ULTRA. The motor speed signal can be used for the internal governor function of MICROBEAST ULTRA. For telemetry transmission it is not necessary as the data will be included in the telemtry signal!<br />
[[File:Hobbywing.png|x300px|none]]
[[File:Hobbywing.png|x300px|none]]
<br />
<br />
{{QUOTE|* Smaller Hobbywing® Platinum models (Platinum 60 and 80) do not measure current. Here displayed current and consumed capacity will stay "0.00". However, you can use the displayed battery voltage to estimate the maximum flight time of the model and to effectively prevent a deep discharge of the battery, i. e. by setting a low voltage alarm in your radio.
{{QUOTE|* There are some Hobbywing® Platinum models (i. e. Platinum "LV" series) that do not measure current. Here current and consumed capacity will stay "0.00". However, you can use the displayed battery voltage to estimate the maximum flight time of the model and to effectively prevent a deep discharge of the battery, i. e. by setting a low voltage alarm in your radio.
* Additionally some ESC do not measure temperature, so Temperature will stay at 0 degrees in your telemetry display. It's no malfunction, there simply is no value available.
* '''Hobbywing® Platinum V3''' ESC don't supply any telemtry output. Anyhow, you can connect the motor speed cable as shown above to MICROBEAST ULTRA. Then you can display motor speed/headspeed on your radio at least!}}<br />
* '''Hobbywing® Platinum V3''' ESC don't supply any telemtry output. Anyhow, you can connect the motor speed cable as shown above to MICROBEAST ULTRA. Then you can display motor speed/headspeed on your radio at least!}}<br />
<br />
<br />
<br />
<br />
{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST ULTRA. The voltage pins of [IO2] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST ULTRA or your ESC if not following these instructions properly!}}<br />
{{WARNING_QUOTE|Please be very careful when connecting your ESC with MICROBEAST ULTRA. The voltage pins of [IO2] mustn't be connected with the telemetry port of your JIVE PRO/KOSMIK ESC. Make sure your wiring looks as shown above and make sure to connect the plugs correctly on each side. Do not interchange the sides of the wire. You can heavily damage your MICROBEAST ULTRA or your ESC if not following these instructions properly!}}<br />
<br />
<br />
==OMP 65A ESC== <!--T:20-->
Connect the control wire of your OMP ESC to port [IO1]. Connect the pin labeled with "TX" from the ESC to the port [IO2] using a single servo wire with plugs on both sides. Optionaly you can connect the yellow wire for measuring the motor speed to the [RPM] input at MICROBEAST ULTRA, so that it is out of the way. For telemetry transmission it is not needed as the data will be included in the telemetry signal!<br />
<br />
Make sure the ESC is sending data with OMP telemetry data protocol. This is the factory setting of the ESC. Do not change the protocol to "SBUS2" or other! MICROBEAST ULTRA will convert the data into your radio's protocol as needed.<br />
<br />
<br />
<br />
<br />