Translations:Manuals:MBUltraFblV5:Radio Setup/4/en: Difference between revisions
Jump to navigation
Jump to search
Importing a new version from external source |
Importing a new version from external source |
||
(One intermediate revision by the same user not shown) | |||
Line 1: | Line 1: | ||
=Bind procedure Spektrum® DSMX satellite= | |||
<p> | <p> | ||
* Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST ULTRA. | * Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST ULTRA. | ||
* Disconnect(!) the Spektrum® remote satellite | * Disconnect(!) the Spektrum® remote satellite (this is different to previous MICROBEAST and MICROBEAST PLUS devices!) | ||
* In case the power is supplied exclusively at the [SYS] connection, to bind a Spektrum® satellite receiver the power supply must be provided temporarily through any of the other ports [CH1] - [CH5].<br /> | * In case the power is supplied exclusively at the [SYS] connection, to bind a Spektrum® satellite receiver the power supply must be provided temporarily through any of the other ports [CH1] - [CH5].<br /> | ||
<br /> | <br /> | ||
{{WARNING_QUOTE|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}} | {{WARNING_QUOTE|'''Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!'''}} | ||
<br /> | <br /> | ||
To bind a '''DSMX''' satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).<br /> | * To bind a '''DSMX''' satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).<br /> | ||
* To select and bind a '''DSM2''' satellite, hold down the button on MICROBEAST ULTRA while switching on the power supply. Here the LED '''N''' on the MICROBEAST ULTRA will flash. Release the button and connect your receiver. Bind the receiver with your transmitter.<br /> | |||
To select and bind a '''DSM2''' satellite, hold down the button on MICROBEAST ULTRA while switching on the power supply. Here the LED '''N''' on the MICROBEAST ULTRA will flash. Release the button and connect your receiver. Bind the receiver with your transmitter.<br /> | |||
<br /> | <br /> | ||
After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' respectively '''N''' flash alternately to all other LEDs for 2 seconds, then MICROBEAST ULTRA will restart. Cycle power and enter receiver setup menu as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.</p> | After successful binding procedure the receiver‘s LED will stay solid. LED '''H''' respectively '''N''' flash alternately to all other LEDs for 2 seconds, then MICROBEAST ULTRA will restart. Cycle power and enter receiver setup menu as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.</p> | ||
<p> | <p> | ||
'''Note:''' | '''Note:''' |
Latest revision as of 10:37, 6 November 2023
Bind procedure Spektrum® DSMX satellite
- Insert a Spektrum® “Bind Plug” at the [SYS] port of MICROBEAST ULTRA.
- Disconnect(!) the Spektrum® remote satellite (this is different to previous MICROBEAST and MICROBEAST PLUS devices!)
- In case the power is supplied exclusively at the [SYS] connection, to bind a Spektrum® satellite receiver the power supply must be provided temporarily through any of the other ports [CH1] - [CH5].
Watch out that the motor can not start accidentally when using the BEC of your speed controller to power the unit!
- To bind a DSMX satellite switch on the power supply now. The yellow LED H on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
- To select and bind a DSM2 satellite, hold down the button on MICROBEAST ULTRA while switching on the power supply. Here the LED N on the MICROBEAST ULTRA will flash. Release the button and connect your receiver. Bind the receiver with your transmitter.
After successful binding procedure the receiver‘s LED will stay solid. LED H respectively N flash alternately to all other LEDs for 2 seconds, then MICROBEAST ULTRA will restart. Cycle power and enter receiver setup menu as further setup steps may be required to use this type of receiver. Remove the bind plug and proceed with the setup as described in the following of this manual.
Note:
- Check carefully what type of receiver you have and what type you setup. You can bind DSMX satellites as "DSM2", which is wrong! An incorrect setting is not obvious but will lead to malfunction or failure of the radio link later in use.
- It makes no difference if you pull off the “Bind Plug” during the binding process or leave it connected as you would expect from some “standard” Spektrum® receivers!