Translations:Manuals:BXFbl:Radio Setup:Jeti EXBUS/20/en: Difference between revisions

From BEASTX Wiki
Jump to navigation Jump to search
FuzzyBot (talk | contribs)
7,906 edits
Importing a new version from external source
 
FuzzyBot (talk | contribs)
7,906 edits
Importing a new version from external source
 
Line 1: Line 1:
==NANOBEAST==
==NANOBEAST==
When not using telemetry connect the EXBUS receiver to DI1 port and power up NANOBEAST.  Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. If needed you can set up your telemetry devices at Menus L & M, if applicable (Menu L = Status LED flashes long once and then 5 times, for Menu L 6 times); push button briefly to skip. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br />
When not using telemetry connect the EXBUS receiver to DI1 port and power up NANOBEAST.  Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br />
<br />
<br />
<br />
<br />

Latest revision as of 12:36, 3 July 2024

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Manuals:BXFbl:Radio Setup:Jeti EXBUS)
==NANOBEAST==
When not using telemetry connect the EXBUS receiver to DI1 port and power up NANOBEAST.  Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.<br />
<br />
<br />

NANOBEAST

When not using telemetry connect the EXBUS receiver to DI1 port and power up NANOBEAST. Connect the push button to SYS port. Push and hold the button for 2 seconds, then release. The Status LED will change color or go off. Push the button again to start the scan process. When scan was successful, the Status LED will flash twice. Now push and hold the button for 2 seconds and release in order to load the default channel assignments. Finally teach throttle failsafe position at Menu N (Status LED flashes long once and then 7 times) by bringing the throttle in lowest position on your radio and push the button again. Now your NANOBEAST will start with init sequence. For further information about RECEIVER MENU setup, see next section. Then perform basic setup procedure in SETUP MENU.


Retrieved from "https://wiki.beastx.com/index.php?title=Translations:Manuals:BXFbl:Radio_Setup:Jeti_EXBUS/20/en&oldid=24831"