Help:StudioX:HMSoft: Difference between revisions
Jump to navigation
Jump to search
Shornstein (talk | contribs) Marked this version for translation |
Shornstein (talk | contribs) No edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
<translate> | <translate> | ||
<!--T:1--> | <!--T:1--> | ||
{{DISPLAYTITLE:(Re)Configuration of BLE2SYS interface|noerror}} | |||
The BLE2SYS interface is a bluetooth to serial bridge. The newer version 2 uses a HM-18 blueotooth stack from DSD Tech. In rare cases, the devices may not have been reconfigured at the factory for use with the BEASTX system. Usually this is the case when the device name is ''HMSOFT'' instead of ''BLE2SYS'' when searching for the device in StudioX.<br /> | The BLE2SYS interface is a bluetooth to serial bridge. The newer version 2 uses a HM-18 blueotooth stack from DSD Tech. In rare cases, the devices may not have been reconfigured at the factory for use with the BEASTX system. Usually this is the case when the device name is ''HMSOFT'' instead of ''BLE2SYS'' when searching for the device in StudioX.<br /> | ||
<br /> | <br /> | ||
| Line 40: | Line 41: | ||
<!--T:9--> | <!--T:9--> | ||
At first enter: AT+ | At first enter: AT+MODE2<br /> | ||
The interface should reply: OK+Set:2<br /> | |||
<br /> | <br /> | ||
Then enter: AT+BAUD?<br /> | |||
The interface should reply: OK+Get:7<br /> | The interface should reply: OK+Get:7<br /> | ||
<br /> | <br /> | ||
In case it shows a different number, the baud rate is not set correctly.<br /> | |||
You can change the setting by entering the command: AT+BAUD7<br /> | You can change the setting by entering the command: AT+BAUD7<br /> | ||
The interface will reply: OK+Set:7<br /> | The interface will reply: OK+Set:7<br /> | ||
<br /> | <br /> | ||
<!--T:11--> | <!--T:11--> | ||
If you like you can change the name of the device: AT+NAMEUSB2SYS<br /> | |||
<br /> | |||
The interface should reply: OK+Set:USB2SYS<br /> | The interface should reply: OK+Set:USB2SYS<br /> | ||
<br /> | <br /> | ||
<!--T:10--> | |||
Finally enter: AT+MODE1<br /> | |||
The interface should reply: OK+Set:1<br /> | |||
<br /> | <br /> | ||
<!--T:12--> | <!--T:12--> | ||
===Connection to StudioX app=== | ===Connection to StudioX app=== | ||
Now setup should be finished. Disconnect the device from the app and close the app completely. Power cycle you BLE2SYS and reconnect to the BEASTX | Now setup should be finished. Disconnect the device from the app and close the app completely. Power cycle you BLE2SYS and reconnect to the BEASTX system's SYS-port. The blue LED on BLE2SYS should be flashing steadily.<br /> | ||
<br /> | <br /> | ||
Start StudioX and search for the device ''BLE2SYS'', if needed (click '''Refresh'''). Then click the '''Connect''' button. The blue LED should light up steadily and you BEASTX system should connect now.<br /> | Start StudioX and search for the device ''BLE2SYS'', if needed (click '''Refresh'''). Then click the '''Connect''' button. The blue LED should light up steadily and you BEASTX system should connect now.<br /> | ||