Translations:Manuals:MB Plus:Preliminary steps/2/de: Difference between revisions

From BEASTX Wiki
Jump to navigation Jump to search
Newer edit →
Created page with "===Einbau des MICROBEAST PLUS=== Befestigen Sie MICROBEAST PLUS mit einem der beiliegenden Klebepads an einer möglichst vibrationsarmen Stelle in Ihrem Helikopter (z.B. auf d..."
(No difference)

Revision as of 12:35, 30 April 2015

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Manuals:MB Plus:Preliminary steps)
==Mounting the Microbeast PLUS unit==
Attach the Microbeast PLUS unit by using one of the provided 3M® gyropads at a preferably low vibrating position on your helicopter such as the gyro platform or receiver platform. You may need to choose another type of mounting pad depending on the vibration pattern of your helicopter. For more information please ask you Microbeast PLUS dealer.
<p>
The MICROBEAST PLUS unit can be attached '''flat or upright''' on the helicopter. However, the '''servo connector pins must always point towards the front or rear''' of the helicopter. The small white sensor pinboard on the side must always be inline with flight direction.</p>
<br />
<div class="noprint">
<gallery widths="400" heights="250" mode="nolines">
Image:450 flat.jpg
Image:450 upright.jpg
</gallery>
</div>
<div class="onlyinprint">
{|
|[[Image:450 flat.jpg|x200px]]
|[[Image:450 upright.jpg|x200px]]
|}
</div>
{{NL}}
<p>
'''Pay attention that the edges of the Microbeast PLUS unit are all parallel with the corresponding rotational axes of the helicopter!''' Especially make sure that the mounting platform is perpendicular to the main shaft! On the other hand it is not important that the unit is directly placed on the rotation axis (which is nearly impossible).</p>
<br />
<div class="noprint">
<gallery widths="500" heights="250" mode="nolines" style="padding:5px 130px; ">
Image:Mounting_trex500.jpg
</gallery>
</div>
<div class="onlyinprint">
{|
|[[Image:Blank_30.png|left]]
|[[Image:Mounting_trex500.jpg]]
|}
[[Image:Blank.png|none]]
</div>
{{NL}}
<p>
'''There are eight possible mounting orientations:'''
<gallery mode="nolines" widths=200px>
File:orient1.jpg|flat, cover on top, servo connectors showing to front
File:orient2.jpg|upright, button on top, servo connectors showing to front
File:orient3.jpg|flat, cover showing to bottom, servo connectors showing to front
File:orient4.jpg|upright, button on bottom, servo connectors showing to front
</gallery>
<gallery mode="nolines" widths=200px>
File:orient5.jpg|flat, cover on top, servo connectors showing to rear
File:orient6.jpg|upright, button on top, servo connectors showing to rear
File:orient7.jpg|flat, cover showing to bottom, servo connectors showing to rear
File:orient8.jpg|upright, button on bottom, servo connectors showing to rear
</gallery>
</p>
{{NL}}

Einbau des MICROBEAST PLUS

Befestigen Sie MICROBEAST PLUS mit einem der beiliegenden Klebepads an einer möglichst vibrationsarmen Stelle in Ihrem Helikopter (z.B. auf der Kreisel- oder Empfängerplattform). Abhängig vom Vibrationspotential des Helikopters kann auch ein anderes, geeigneteres Klebepad für die einwandfreie Funktion notwendig sein. Bei Fragen hierzu wenden Sie sich bitte an Ihren MICROBEAST PLUS Fachhändler.

Der Einbau des MICROBEAST PLUS kann wahlweise flach oder hochkant erfolgen, auch verkehrt herum unter dem Helikopter. Die Stecker der Anschlusskabel müssen aber immer in oder gegen die Flugrichtung des Helikopters zeigen.




Achten Sie darauf, dass die Gehäusekanten von MICROBEAST PLUS absolut parallel zu den Drehachsen des Helikopters ausgerichtet sind und der Montageort auf der Roll- und Nickachse winkelrichtig zur Hauptrotorwelle ist!

Retrieved from "https://wiki.beastx.com/index.php?title=Translations:Manuals:MB_Plus:Preliminary_steps/2/de&oldid=5001"