Translations:Manuals:MB Plus:Receiver Installation/5/de: Difference between revisions

From BEASTX Wiki
Jump to navigation Jump to search
Created page with "Grundsätzlich wird das Kabel für die Übertragung des Singlelinesignals beim MICROBEAST PLUS an den Anschluss [ELE/DI1] angesteckt. Wenn Sie das Signal eines einzelnen Spekt..."
(No difference)

Revision as of 13:20, 4 May 2015

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Manuals:MB Plus:Receiver Installation)
<p>
In general the single-line connection wire is plugged into the [DI1] input of MICROBEAST PLUS. When using the signal of a single Spektrum® remote satellite you must connect the optional available Spektrum® satellite adapter (Order Nr. BXA76009) in between, in order to supply the remote satellite with the correct voltage level (figure 3).</p>
<p>
The throttle servo or ESC is connected to the [CH5] output. When using a speed controller with BEC, from here the power will be distributed to receiver and servos. Alternatively or additionally you can connect a power supply/second BEC wire/buffering battery to the [SYS] port. '''Note that all plus and minus connectors are bridged on the MICROBEAST PLUS. Only at the triple input/output [AUX|PIT|RUD] you musn't connect any power source as this is not part of the power rail!''' When using a big heli with standard size servos it may be insufficient to only provide power at the [SYS] port! If there are no other ports left to (additionally) feed in power, we highly recommend using the [[Manuals:MB_Plus:Intro_3|MICROBEAST PLUS HD]] with separate high power input.</p>
<p>
Using a single-line receiver with additional servo output ports you can choose between connecting throttle servo/ESC and additional devices to MICROBEAST PLUS (figure 1) or directly to the receiver (figure 2). But note that when connecting the power supply at the receiver, MICROBEAST PLUS and the servos will only be supplied over the small single-line connection. Especially on big helis with standard size servos this might not be sufficient! Here it is mandatory to connect some supply lines in parallel to other free ports, such as [SYS] or [CH5] or better connect the power supply (i.e. ESC with BEC supply) directly to the MICROBEAST PLUS as shown in figure 1.</p>
{|cellspacing="40" style="text-align:center;"
|[[Image:Singleline_RX.png | x150px]]
|[[Image:Singleline_RX_2.png | x150px]]
|[[Image:Spektrum_RX_Sat.png | x150px]]
|- style="text-align:center;"
| Wiring layout for single-line receivers
| Alternative wiring layout for single-line receiver<br /> with additional servo output channels
| JR®/Spektrum® remote satellite connection with power adapter
|}
{{QUOTE|[[Image:Warning.png|18px|sub]] Ensure a tight fit of the connectors. The pin board of MICROBEAST PLUS is designed so that the plugs firmly clamp each other when they are fully inserted. Nevertheless, especially when using a single-line receiver, it is possible that connectors are plugged in with no adjacent neighbors. Such plugs should additionally be secured against loosening.}}

Grundsätzlich wird das Kabel für die Übertragung des Singlelinesignals beim MICROBEAST PLUS an den Anschluss [ELE/DI1] angesteckt. Wenn Sie das Signal eines einzelnen Spektrum Satellitenempfängers empfangen wollen, beachten Sie, dass hier unbedingt der separat erhältliche Spektrum Satellitenadapter (Best.Nr. BXA76009) zwischengesteckt werden muss, der die Ausgangsspannung auf ein notwendiges Mass reduziert.