Bureaucrats, Administrators, translate-proofr
15,724
edits
Changes
Jump to navigation
Jump to search
Line 70:
Line 70: − + + + − + + + − + − + − + + + + + +
no edit summary
===MICROBEAST does not finish initialization. What can I do?=== <!--T:43-->
===MICROBEAST does not finish initialization. What can I do?=== <!--T:43-->
Watch the running LED lights during the init phase: If the lights A - G light up the sensor's rest positions are beeing calibrated, H - N show determining the RC channels and their center positions. Initially the chase is from A - N. If one step is done the indication light for this step will quit running.
Watch the running LED lights during the init phase: If the lights A - G light up the sensor's rest positions are beeing calibrated, H - N show determining the RC channels and their center positions.
MICROBEAST/AR7x00BX: Initially the chase is from A - N. If one step is done the indication light for this step will quit running.
MICROBEAST PLUS: Initially the chase is from H - N (Stick calibration). Only if this step is finished the chase from A - G (Sensor calibration) will start.
<!--T:44-->
<!--T:44-->
When LEDs A - G do not quit running
When LEDs A - G do not quit running
* The sensors register movement and calibration of rest position can not be finished. Make sure the unit/the helicopter does not get moved e.g. by wind gusts or people leaning on your work bench.
* The sensors register movement and calibration of rest position can not be finished. Make sure the unit/the helicopter does not get moved e.g. by wind gusts or people leaning on your work bench where the heli is standing on.
* Sensors damaged. Return the device for repair.
* Power supply voltage is dropping due to weak power supply or damaged servos.
<!--T:45-->
<!--T:45-->
When LEDs H - N do not quit running
When LEDs H - N do not quit running
* All MICROBEAST/MICROBEAST PLUS: Check whether the receiver sends out control signals and that all cables are properly connected to the MICROBEAST. In particular make sure the plugs are inserted with correct polarity and not offset to the pin connectors of the MICROBEAST.
* Check whether the receiver sends out control signals and that all cables are properly connected to the MICROBEAST/MICROBEAST PLUS. In particular make sure the plugs are inserted with correct polarity and not offset to the pin connectors of the MICROBEAST.
<!--T:46-->
<!--T:46-->
* MICROBEAST/MICROBEAST PLUS Version 2.0.0 and greater: Is the correct type of receiver selected in the receiver setup menu? See [[Setup receiver type - Microbeast, Trajectory]]
* Is the correct type of receiver selected in the [[Manuals:MB_Plus:Receiver_setup_intro|receiver setup menu]]? Particularly when using a Spektrum® radio system note that receivers like Spektrum® AR6100, 7000, 9000 etc. are "Standard" receivers! The selection of "Spektrum®" in the receiver setup menu only applies for direct connection of one single Spektrum satellite with the optional available adapter. In general when using a serial-wire receiver check if the Status-LED lights up in "blue" color at [[Manuals:MB_Plus:Receiver_setup_menu_B|Receiver setup menu point '''B''']] indicating there is a valid signal coming from the receiver.
* AR7200BX: Check binding between transmitter and unit.
* When using a Standard receiver check the wiring. Mainly check receiver wires for polarity on both sides and correct plugging (no vertical offset by one pin).
* MICROBEAST/MICROBEAST PLUS: Check binding between transmitter and receiver.
* AR7200BX/AR7300BX: Check binding between transmitter and receiver.
<br />
<br />
===The brand new MICROBEAST only shows a red flashing LED or even nothing. What's wrong?=== <!--T:47-->
===The brand new MICROBEAST only shows a red flashing LED or even nothing. What's wrong?=== <!--T:47-->