Translations:StudioX Plugins/1/en: Difference between revisions
Importing a new version from external source |
Importing a new version from external source |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
== Connecting a BEASTX gyro to the computer == | |||
All BEASTX gyros come with a serial communication port which typically is marked with the letters ''SYS''. Connect the servo wire coming from your USB interface to this port. Make sure to connect the wire in correct polarity on both sides! When using the USB2SYS interface you have to power the device with a separate power supply, i.e. receiver battery or BEC of the R/C model. It will not be powered from the USB port.<br /> | |||
== Connecting a BEASTX | |||
All BEASTX | |||
<br /> | <br /> | ||
<div style= "padding: 0px 50px;"> | <div style= "padding: 0px 50px;"> | ||
| Line 25: | Line 7: | ||
<br /> | <br /> | ||
<br /> | <br /> | ||
Also you can use a RX2SIM Wireless Multi-Sim Adapter instead of the USB2SYS interface. For this you can switch the RX2SIM into an USB2SYS emulation mode (push button on the RX2SIM several times until the LED lights up in orange color). In this configuration the BEASTX gyro will be powered from the USB port. Anyhow, this only will work when receiver and servos are not connected to the gyro! Otherwise the power of the USB port will not be sufficient to supply all consumers. In this case you have to power the device from the receiver battery as well. '''But here when using more than 6 Volts (i. e. using a 2s Lipo battery as receiver power supply) you must disconnect the red wire (plus pole) from the servo wire going to the interface. Otherwise you will damage the RX2SIM and/or USB port of your computer!'''<br /> | |||
<br /> | <br /> | ||
<table> | <table> | ||
| Line 32: | Line 14: | ||
<td style= "padding: 0px 50px;">[[File:RX2SIM_MBPlus_powered.png|400px]]</td> | <td style= "padding: 0px 50px;">[[File:RX2SIM_MBPlus_powered.png|400px]]</td> | ||
</tr> | </tr> | ||
</table> | </table><br /> | ||
<br /> | |||
<br /> | <br /> | ||
Latest revision as of 11:06, 13 November 2017
Connecting a BEASTX gyro to the computer
All BEASTX gyros come with a serial communication port which typically is marked with the letters SYS. Connect the servo wire coming from your USB interface to this port. Make sure to connect the wire in correct polarity on both sides! When using the USB2SYS interface you have to power the device with a separate power supply, i.e. receiver battery or BEC of the R/C model. It will not be powered from the USB port.
Also you can use a RX2SIM Wireless Multi-Sim Adapter instead of the USB2SYS interface. For this you can switch the RX2SIM into an USB2SYS emulation mode (push button on the RX2SIM several times until the LED lights up in orange color). In this configuration the BEASTX gyro will be powered from the USB port. Anyhow, this only will work when receiver and servos are not connected to the gyro! Otherwise the power of the USB port will not be sufficient to supply all consumers. In this case you have to power the device from the receiver battery as well. But here when using more than 6 Volts (i. e. using a 2s Lipo battery as receiver power supply) you must disconnect the red wire (plus pole) from the servo wire going to the interface. Otherwise you will damage the RX2SIM and/or USB port of your computer!
 |
 |