Manuals:MBPlusFblV5:Box Content: Difference between revisions

From BEASTX Wiki
Jump to navigation Jump to search
← Older edit
No edit summary
No edit summary
 
(8 intermediate revisions by the same user not shown)
Line 1: Line 1:
__NOTOC__
<translate>
<translate>
<!--T:1-->
{{DISPLAYTITLE:Box content and accessories|noerror}}
{{DISPLAYTITLE:Box content and accessories|noerror}}
{{TOC_MBPlusV5}}
{{TOC_MBPlusV5|Manuals:MBPlusFblV5:Intro/en|Manuals:MBPlusFblV5:Hardware_Installation/en}}
__TOC__
<br />
 
= This is what you get when buying the MICROBEAST PLUS = <!--T:2-->
<br />
{|
|- style="vertical-align:bottom;"
|[[File:Box contents mbplus.png|none|x250px]]<br />
|
* the MICROBEAST PLUS flybarless unit
* printed Quickstart manual, Quick reference card and BEASTX sticker set
* all the wires to connect your receiver to the system (wire length 150mm)
* 3M gyro pads
* plastic tool for adjusting the gain dials
<br />
|}
'''Please note:''' MICROBEAST PLUS is usually sold with BASIC firmware. If you like, you can upgrade to PROEDITION firmware later using the StudioX PC software or StudioXm app. Ask your dealer if you need the PROEDITION firmware upgrade installed already.<br />
<br />
<br />
 
= This is what you get when buying the MICROBEAST PLUS HD= <!--T:3-->
<br />
{|
|- style="vertical-align:bottom;"
|[[File:Box contents mbplusHD.png|none|x250px]]
| <br />
<br />
* the MICROBEAST PLUS HD flybarless unit
* printed Quickstart manual, Quick reference card and BEASTX sticker set
* all the wires to connect your receiver to the system (wire length 150mm)
* 3M gyro pads
* plastic tool for adjusting the gain dials
* high power connector and on/off switch
|}<br />
<br />
'''Please note:''' MICROBEAST PLUS HD is usually sold with BASIC firmware. If you like, you can upgrade to PROEDITION firmware later using the StudioX PC software or StudioXm app. Ask your dealer if you need the PROEDITION firmware upgrade installed already.<br />
<br />
<br />
 
= Optional accessory = <!--T:4-->
<br />
 
<!--T:5-->
'''USB2SYS'''<br />
[[File:Usb2sys.jpg|none|x120px]]<br />
<br />
USB2SYS connects your MICROBEAST PLUS / MICROBEAST PLUS HD with your computers USB port. With the StudioX Software (available for Windows and macOS) you can easily configure the system, create backups of your settings, load heli presets, upload firmware update file to your unit and much more.<br />
<br />
For more information please see the [[StudioXm/en|StudioX manual]].<br />
<br />
 
<!--T:6-->
'''BLE2SYS'''<br />
[[File:Ble2sys.jpg|none|x120px]]<br />
<br />
BLE2SYS is a Bluetooth Smart Interface that allows to connect your MICROBEAST PLUS / MICROBEAST PLUS HD to your smartphone or tablet. With the StudioXm app (available for Android and iOS) you can easily configure the system, create backups of your settings, load heli presets, upload firmware update file to your unit and much more. Please note that your mobile device must be Bluetooth Smart/Bluetooth LE compatible.<br />
<br />
For more information please see the [[StudioXm/en|StudioXm manual]].<br />
<br />
<br />
 
</translate>
</translate>

Latest revision as of 12:38, 30 August 2018

MICROBEAST PLUS V5

1. Introduction

2. Box content and accessories

3. Hardware installation

4. Radio system

5. Receiver Menu

6. Basic setup
Device orientation
Swashplate servos
Rudder pulse width
Rudder frequency
Rudder control
Swash mixing
Servo trim
Servo directions
Cyclic throw
Collective pitch
Servo limit
Cyclic directions
7. Headspeed Governor
Activating the governor
Sensor test mode
Throttle low position
Throttle high position
Transmitter setup
Signal divider
Main gear ratio
8. Additional settings
Trimming
Control style
Special parameters
Gains

9. AttitudeControl (Self leveling)

10. Bank Switching

11. Factory reset

12. Version information

13. Firmware update

← →


This is what you get when buying the MICROBEAST PLUS
  • the MICROBEAST PLUS flybarless unit
  • printed Quickstart manual, Quick reference card and BEASTX sticker set
  • all the wires to connect your receiver to the system (wire length 150mm)
  • 3M gyro pads
  • plastic tool for adjusting the gain dials


Please note: MICROBEAST PLUS is usually sold with BASIC firmware. If you like, you can upgrade to PROEDITION firmware later using the StudioX PC software or StudioXm app. Ask your dealer if you need the PROEDITION firmware upgrade installed already.


This is what you get when buying the MICROBEAST PLUS HD


  • the MICROBEAST PLUS HD flybarless unit
  • printed Quickstart manual, Quick reference card and BEASTX sticker set
  • all the wires to connect your receiver to the system (wire length 150mm)
  • 3M gyro pads
  • plastic tool for adjusting the gain dials
  • high power connector and on/off switch



Please note: MICROBEAST PLUS HD is usually sold with BASIC firmware. If you like, you can upgrade to PROEDITION firmware later using the StudioX PC software or StudioXm app. Ask your dealer if you need the PROEDITION firmware upgrade installed already.


Optional accessory


USB2SYS



USB2SYS connects your MICROBEAST PLUS / MICROBEAST PLUS HD with your computers USB port. With the StudioX Software (available for Windows and macOS) you can easily configure the system, create backups of your settings, load heli presets, upload firmware update file to your unit and much more.

For more information please see the StudioX manual.

BLE2SYS



BLE2SYS is a Bluetooth Smart Interface that allows to connect your MICROBEAST PLUS / MICROBEAST PLUS HD to your smartphone or tablet. With the StudioXm app (available for Android and iOS) you can easily configure the system, create backups of your settings, load heli presets, upload firmware update file to your unit and much more. Please note that your mobile device must be Bluetooth Smart/Bluetooth LE compatible.

For more information please see the StudioXm manual.


Retrieved from "https://wiki.beastx.com/index.php?title=Manuals:MBPlusFblV5:Box_Content&oldid=16563"