BEASTX Updater Classic: Difference between revisions

From BEASTX Wiki
Jump to navigation Jump to search
← Older edit
No edit summary
No edit summary
 
(74 intermediate revisions by the same user not shown)
Line 1: Line 1:
===Uninstall existing Software (Windows only)===
<translate>
Uninstall any existing BEASTXUpdater/Microsettings installation prior to install the BEASTXSoftware bundle.
<!--T:1-->
The tool "BEASTX Updater Classic" can be used if you encounter problems with the StudioX application and want to check if your device can be recognized at all. Also you can use it to do a firmware update with a provided update file from the BEASTX service team if necessary. You can find the BEASTX Updater Classic here:<br />
<br />
[http://studiox.beastx.com/download/misc/BXUpdaterClassic.zip Updater Classic for Windows]<br />
<br />
[http://studiox.beastx.com/download/misc/BXUpdaterClassic.pkg Updater Classic for macOS]<br />
<br />


===Download Update Software and Install===
<!--T:47-->
'''On Windows computers make sure that the driver files for your USB2SYS interface have been installed or install the files if necessary.''' For further information see this page: [[USB2SYS/SPMA3030 driver installation]].<br />
<br />


Supported operating systems are:
<!--T:11-->
'''1. Connecting to the BEASTX device'''


    Windows (XP, Vista, 7, 8, 8.1)
<!--T:49-->
    MacOS 10.6.x and later
The BEASTX device will not be powered from the USB2SYS-Interface! So the unit must be supplied with power from a different source
before(!) you connect it to the PC, e.g. simply switch on tx and rx as you would go flying (on electric helis take care of the motor!).


===Driver installation===
<!--T:12-->
Windows:
The cable from the interface goes into the '''[SYS]''' port of the device. Watch out for correct polarity on both devices.<br />
The driver installation will not be launched automatically during setup.
<br />
The installer will be copied and a link to it is added to the BEASTX group in Start-Menu. Do not connect the USB2SYS interface to the computer unless you did not perform the driver installation. After the installation when you connect the interface to the PC, Windows recognize the device and install it as a new device.


MacOS:
<!--T:13-->
The driver is inside the Disk-Image and must be installed manually.
If the COM-Port to which the USB2SYS-Interface has been assigned by windows is known, you can directly choose it from the list of available interfaces. On macOS/Linux usually the port is called "cu.SLAB_USBtoUART" or "tty.SLAB_USBtoUART" (you can use either of them):


===Validate driver installation (Windows only)===
<!--T:14-->
After successful installation of the driver, when the USB2SYS-Interface is connected to the PC, you must be able to find following entry in the Windwos Device Manager:
[[File:Step 5_1.png|200px|thumb|none]]
Klicken Sie auf die Grafik für eine größere Ansicht  Name: Step 4.png  Hits: 1496  Größe: 47,1 KB  ID: 598
 
<!--T:15-->
<br />
If the COM-Port is not known you can use the "Autodetect…" function:
 
<!--T:16-->
[[File:Step 5_2.jpg|200px|thumb|none]]
 
<!--T:17-->
<br />
When the dialog is shown, disconnect the USB2SYS-Interface from the PC (if already connected) and reconnect it again.
The Autodetect-function will only work if the driver was installed successfully.
 
<!--T:18-->
[[File:Step 5_3.jpg|200px|thumb|none]]
 
<!--T:19-->
<br />
After a successful detection the BEASTX Updater Classic will tell you which COM-Port was detected:
 
<!--T:20-->
[[File:Step 5_4.jpg|200px|thumb|none]]
 
 
<!--T:21-->
<br />
'''2. Detection of the BEASTX device'''
 
<!--T:50-->
After you selected a COM-Port the BEASTX Updater Classic will automatically try to identify the unit connected to it.
 
<!--T:22-->
If the MICROBEAST PLUS/AR7210BX/nanoBEAST was not connected at this moment you can manually force a new detection by pressing the "Refresh" button.
 
<!--T:23-->
If the correct COM-Port was chosen (red), and the device is connected to the USB2SYS-Interface, some information (green) about it will be shown in the "BEASTX Device" section:
 
 
<!--T:24-->
[[File:Step 6.jpg|200px|thumb|none]]
 
 
<!--T:25-->
* Hardware-Version 1.1 and 1.2 stand for MICROBEAST units. Hardware-Version 2.x shows that a MICROBEAST PLUS is connected. Hardware Version 8.0 identifies Spektrum AR7200BX units.
* Application-Version is the actually installed firmware of the device (in this case 1.0.0).
* Data-Version is the format that is used to store settings on the MICROBEAST.
* Serial-Number is an unique identifier for each device.
 
 
<!--T:26-->
'''3. Select Update-File'''
 
<!--T:51-->
If the device was successfully identified you can go on with selecting an Update-File:
 
<!--T:27-->
"Open File…" button opens a dialog where you can choose the Update-File.
 
<!--T:28-->
[[File:Step 7_1.png|200px|thumb|none]]
 
 
<!--T:29-->
Or you can just drag'n'drop an Update-File from the Explorer to the Main window of the BEASTXUpdater.
 
<!--T:30-->
An Updates-File can only be loaded if it is free of damage, complete and has the mentioned ".upd" ending.
 
<!--T:31-->
Application-Version, Data-Version and Target-Hardware will be shown if the file was loaded successfully:
 
 
<!--T:32-->
[[File:Step 7_2.jpg|200px|thumb|none]]
 
 
<!--T:33-->
Only a compatible "Target Hardware Version" can be installed to your device.
The firmware version in the Update-File will be shown next to "Application Version" (in this case 1.0.11).
 
<!--T:34-->
The format of settings will be shown next to "Data Version". '''IMPORTANT''': If the major version of the "Data Version" is different between the actual and new firmware, then the Basic-Setup has to be done again after the update.
 
 
<!--T:35-->
'''4. Perform Update'''
 
<!--T:52-->
If a valid COM-Port is selected an a valid Update-File was loaded, the "Start Update…" button will be enabled:
 
<!--T:36-->
[[File:Step 8_1.jpg|200px|thumb|none]]


The name COM3 may be different on your PC. This entry must disappear when you disconnect the USB2SYS-Interface from the PC, and reappear when you connect it again.


To access the device manager under windows 7 type devmgmt.msc in the Startmenu's search bar. Alternatively you can enter the computer properties by pressing and holding the START key on the keyboard and addtionaly pressing the PAUSE key. Then click on device manager in the upper left corner of the appearing window.
<!--T:37-->
After pressing the "Start Update…" button, the actual firmware version, and the new target firmware version will be shown:


===Start BEASTXUpdater===
<!--T:38-->
IMPORTANT: The MICROBEAST will not be powered from the USB2SYS-Interface, so the MICROBEAST must be supplied with power from a different source BEFORE you connect it to the PC, e.g. simply switch on tx and rx as you would go flying (on electric helis take care of the motor!).
[[File:Step 8_2.png|200px|thumb|none]]


The cable from the interface goes into the Microbeast's [SYS] port. Watch out for correct polarity on both devices.


If the COM-Port, to which the USB2SYS-Interface has been assigned by windows, is known you can directly choose it from the list of available interfaces:
<!--T:39-->
Klicken Sie auf die Grafik für eine größere Ansicht  Name: Step 5_1.png  Hits: 753  Größe: 96,0 KB  ID: 599
Press "Yes" to start the update.


If the COM-Port is not known you can use the "Autodetect…" function:
<!--T:40-->
Klicken Sie auf die Grafik für eine größere Ansicht  Name: Step 5_2.jpg  Hits: 441  Größe: 38,7 KB  ID: 600
After a successful update a message will be displayed:
Klicken Sie auf die Grafik für eine größere Ansicht  Name: Step 5_3.jpg  Hits: 471  Größe: 42,9 KB  ID: 601
 
<!--T:41-->
[[File:Step 8_3.png|200px|thumb|none]]


When the dialog is shown, disconnect the USB2SYS-Interface from the PC (if already connected) and reconnect it again.
The Autodetect-function will only work if the driver was installed successfully.


After a successful detection the BEASTXUpdater will tell you which COM-Port was detected:
<!--T:42-->
Klicken Sie auf die Grafik für eine größere Ansicht  Name: Step 5_4.jpg  Hits: 437  Größe: 42,3 KB  ID: 602
After your confirmation with "Ok" BEASTX Updater Classic will detect the version information of the connected the device again.


===Detect connected BEASTX device===
<!--T:43-->
After you selected a COM-Port the BEASTXUpdater will automatically try to identify the unit connected to it.
[[File:Step 8_4.png|200px|thumb|none]]


If the MICROBEAST/Trajectory/AR7200BX was not connected at this moment you can manually force a new detection by pressing the "Refresh" button (or "Connect" when using the MicroSettings Software).


If the correct COM-Port was chosen (red), and the MICROBEAST is connected to the USB2SYS-Interface, some information (green) of this MICROBEAST will be shown in the "BEASTX Device" section:
<!--T:44-->
Klicken Sie auf die Grafik für eine größere Ansicht  Name: Step 6.jpg  Hits: 628  Größe: 48,7 KB  ID: 603
You can refresh this information using the "Refresh" button.


At this moment Hardware-Version 1.1 and 1.2 are existing.
<!--T:45-->
Application-Version is the actually installed firmware of the MICROBEAST (in this case 1.0.0)
Your device is now updated to the latest firmware.
Data-Version is the format of the settings, stored on the MICROBEAST.
</translate>
Serial-Number is a unique identifier for each MICROBEAST.

Latest revision as of 18:42, 6 August 2018

The tool "BEASTX Updater Classic" can be used if you encounter problems with the StudioX application and want to check if your device can be recognized at all. Also you can use it to do a firmware update with a provided update file from the BEASTX service team if necessary. You can find the BEASTX Updater Classic here:

Updater Classic for Windows

Updater Classic for macOS

On Windows computers make sure that the driver files for your USB2SYS interface have been installed or install the files if necessary. For further information see this page: USB2SYS/SPMA3030 driver installation.

1. Connecting to the BEASTX device 

The BEASTX device will not be powered from the USB2SYS-Interface! So the unit must be supplied with power from a different source
before(!) you connect it to the PC, e.g. simply switch on tx and rx as you would go flying (on electric helis take care of the motor!).

The cable from the interface goes into the [SYS] port of the device. Watch out for correct polarity on both devices.

If the COM-Port to which the USB2SYS-Interface has been assigned by windows is known, you can directly choose it from the list of available interfaces. On macOS/Linux usually the port is called "cu.SLAB_USBtoUART" or "tty.SLAB_USBtoUART" (you can use either of them):


If the COM-Port is not known you can use the "Autodetect…" function:


When the dialog is shown, disconnect the USB2SYS-Interface from the PC (if already connected) and reconnect it again. The Autodetect-function will only work if the driver was installed successfully.


After a successful detection the BEASTX Updater Classic will tell you which COM-Port was detected:



2. Detection of the BEASTX device

After you selected a COM-Port the BEASTX Updater Classic will automatically try to identify the unit connected to it.

If the MICROBEAST PLUS/AR7210BX/nanoBEAST was not connected at this moment you can manually force a new detection by pressing the "Refresh" button.

If the correct COM-Port was chosen (red), and the device is connected to the USB2SYS-Interface, some information (green) about it will be shown in the "BEASTX Device" section:



  • Hardware-Version 1.1 and 1.2 stand for MICROBEAST units. Hardware-Version 2.x shows that a MICROBEAST PLUS is connected. Hardware Version 8.0 identifies Spektrum AR7200BX units.
  • Application-Version is the actually installed firmware of the device (in this case 1.0.0).
  • Data-Version is the format that is used to store settings on the MICROBEAST.
  • Serial-Number is an unique identifier for each device.


3. Select Update-File

If the device was successfully identified you can go on with selecting an Update-File:

"Open File…" button opens a dialog where you can choose the Update-File.


Or you can just drag'n'drop an Update-File from the Explorer to the Main window of the BEASTXUpdater.

An Updates-File can only be loaded if it is free of damage, complete and has the mentioned ".upd" ending.

Application-Version, Data-Version and Target-Hardware will be shown if the file was loaded successfully:



Only a compatible "Target Hardware Version" can be installed to your device. The firmware version in the Update-File will be shown next to "Application Version" (in this case 1.0.11).

The format of settings will be shown next to "Data Version". IMPORTANT: If the major version of the "Data Version" is different between the actual and new firmware, then the Basic-Setup has to be done again after the update.


4. Perform Update

If a valid COM-Port is selected an a valid Update-File was loaded, the "Start Update…" button will be enabled:


After pressing the "Start Update…" button, the actual firmware version, and the new target firmware version will be shown:


Press "Yes" to start the update.

After a successful update a message will be displayed:


After your confirmation with "Ok" BEASTX Updater Classic will detect the version information of the connected the device again.


You can refresh this information using the "Refresh" button.

Your device is now updated to the latest firmware.

Retrieved from "https://wiki.beastx.com/index.php?title=BEASTX_Updater_Classic&oldid=16420"