Translations:Help:StudioX/18/en: Difference between revisions

From BEASTX Wiki
Jump to navigation Jump to search
Newer edit →
FuzzyBot (talk | contribs)
7,906 edits
Importing a new version from external source
 
FuzzyBot (talk | contribs)
7,906 edits
Importing a new version from external source
Line 6: Line 6:
<br />
<br />
Usually when you click "Connect" button, the LED on the BLE2SYS must light up solid blue and data transfer should be displayed in the Studiox app. When LED goes off and you get the message "No device found", power off everything and again check for proper connection between BLE2SYS and MICROBEAST SYS port. Completely close the StudioX app (on iPhone double tap Home button and swipe StudioX app away, on Android hold menu button and swipe app away). Then power on Microbeast and BLE2SYS. Start StudioX app again and try again. Ideally BLE2SYS should be selected already in the menu bar, so just click "Connect" button immediately when app opens.<br />
Usually when you click "Connect" button, the LED on the BLE2SYS must light up solid blue and data transfer should be displayed in the Studiox app. When LED goes off and you get the message "No device found", power off everything and again check for proper connection between BLE2SYS and MICROBEAST SYS port. Completely close the StudioX app (on iPhone double tap Home button and swipe StudioX app away, on Android hold menu button and swipe app away). Then power on Microbeast and BLE2SYS. Start StudioX app again and try again. Ideally BLE2SYS should be selected already in the menu bar, so just click "Connect" button immediately when app opens.<br />
<br />
<br />
<br />

Revision as of 12:49, 23 December 2021

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Help:StudioX)
==StudioX doesn't recognize the BEASTX system when using BLE2SYS bluetooth interface==
* The BLE2SYS interface must be connected to the SYS port of the BEASTX device. Watch out for correct polarity! Make sure the LED on the BLE2SYS flashes slow and steady. By default the interface deactivates after 30 seconds when there is no connection. In this case the LED is off. You have to cylce power in order to reactivate the device.
* When LED on BLE2SYS is flashing repeatedly in short intervals the device is locked due to wrong pin code. Also in this case, power cycle and try again.
* Keep some distance between smartphone and bluetooth device (apprx. 30cm or 1 ft). When both devices are too close, the bluetooth connection can be interupted.
* Make sure there are no other devices around that can interfere with the 2,4GHz bluetooth connection. I.e. power off your radio transmitter or make sure to keep it at bigger distance to the helicopter. There have been reports that radio systems can interfer with the bluetooth connection when devices are on the work bench altogether!<br />
<br />
Usually when you click "Connect" button, the LED on the BLE2SYS must light up solid blue and data transfer should be displayed in the Studiox app. When LED goes off and you get the message "No device found", power off everything and again check for proper connection between BLE2SYS and your device's SYS port. Completely close the StudioX app (on iPhone double tap Home button and swipe StudioX app away, on Android hold menu button and swipe app away). Then power cycle your BEASTX and BLE2SYS. Start StudioX app again and try again. Ideally BLE2SYS should be selected already in the menu bar, so just click "Connect" button immediately when app opens.<br />
<br />
<br />

StudioX does not recognize my device (BLE2SYS)

  • The BLE2SYS interface must be connected to the SYS port; watch out for correct polarity! Make sure the LED on the BLE2SYS flashes in intervals of 2 seconds. By default the interface deactivates after 30 seconds when there is no connection. In this case the LED is off. You have to cylce power in order to reactivate the device.
  • When LED on BLE2SYS is flashing repeatedly in short intervals the device is locked due to wrong pin code. Also in this case, power cycle and try again.
  • Keep some distance between smartphone and bluetooth device (apprx. 30cm or 1 ft). When both devices are too close, the bluetooth connection can be interupted.
  • Make sure there are no other devices around that can interfere with the 2,4GHz bluetooth connection. I.e. power off your radio transmitter or make sure to keep it at bigger distance to the helicopter. There have been reports that radio systems can interfer with the bluetooth connection when devices are on the work bench altogether!


Usually when you click "Connect" button, the LED on the BLE2SYS must light up solid blue and data transfer should be displayed in the Studiox app. When LED goes off and you get the message "No device found", power off everything and again check for proper connection between BLE2SYS and MICROBEAST SYS port. Completely close the StudioX app (on iPhone double tap Home button and swipe StudioX app away, on Android hold menu button and swipe app away). Then power on Microbeast and BLE2SYS. Start StudioX app again and try again. Ideally BLE2SYS should be selected already in the menu bar, so just click "Connect" button immediately when app opens.


Retrieved from "https://wiki.beastx.com/index.php?title=Translations:Help:StudioX/18/en&oldid=19103"