Difference between revisions of "Translations:Manuals:BXFbl:Radio Setup:RemoteSat/25/en"

From BEASTX Wiki
Jump to navigation Jump to search
(Importing a new version from external source)
(Importing a new version from external source)
 
Line 1: Line 1:
−
'''MICROBEAST ULTRA'''<br />
+
'''MICROBEAST ULTRA (v5.9.x)'''<br />
−
* Insert a Spektrum® ''Bind Plug'' at the '''[AUX|PIT|RUD]''' port.
+
* Disconnect(!) the Spektrum® remote satellite and switch on the power supply.
−
* Disconnect(!) the Spektrum® remote satellite
+
* During init sequence (LED light H-N is running) push and hold the button for 4 seconds, then release
−
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST ULTRA will start to flash. Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
+
* LEDs A and H flash in alternating sequence
−
* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
+
* Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash in combination with LED A on MICROBEAST
 +
* Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
 +
* After successful binding procedure the receiver‘s LED will stay solid
 +
* Your MICROBEAST will restart and enter RECEIVER MENU. Press button briefly to scan for the receiver and proceed.
 
<br />
 
<br />
 
<br />
 
<br />

Latest revision as of 18:39, 30 May 2024

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Manuals:BXFbl:Radio Setup:RemoteSat)
'''MICROBEAST ULTRA (v5.9.x)'''<br />
* Disconnect(!) the Spektrum® remote satellite and switch on the power supply.
* During init sequence (LED light H-N is running) push and hold the button for 4 seconds, then release
* LEDs A and H flash in alternating sequence
* Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash in combination with LED A on MICROBEAST
* Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* After successful binding procedure the receiver‘s LED will stay solid
* Your MICROBEAST will restart and enter RECEIVER MENU. Press button briefly to scan for the receiver and proceed.
<br />
<br />
Translation'''MICROBEAST ULTRA (v5.9.x)'''<br />
* Disconnect(!) the Spektrum® remote satellite and switch on the power supply.
* During init sequence (LED light H-N is running) push and hold the button for 4 seconds, then release
* LEDs A and H flash in alternating sequence
* Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash in combination with LED A on MICROBEAST
* Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* After successful binding procedure the receiver‘s LED will stay solid
* Your MICROBEAST will restart and enter RECEIVER MENU. Press button briefly to scan for the receiver and proceed.
<br />
<br />

MICROBEAST ULTRA (v5.9.x)

  • Disconnect(!) the Spektrum® remote satellite and switch on the power supply.
  • During init sequence (LED light H-N is running) push and hold the button for 4 seconds, then release
  • LEDs A and H flash in alternating sequence
  • Now connect your remote satellite to the pin board. The receiver's yellow LED will start to flash in combination with LED A on MICROBEAST
  • Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
  • After successful binding procedure the receiver‘s LED will stay solid
  • Your MICROBEAST will restart and enter RECEIVER MENU. Press button briefly to scan for the receiver and proceed.



Retrieved from "https://wiki.beastx.com/index.php?title=Translations:Manuals:BXFbl:Radio_Setup:RemoteSat/25/en&oldid=23779"