Bureaucrats, Administrators, translate-proofr
15,683
edits
Changes
Jump to navigation
Jump to search
Line 2:
Line 2: − ===1. Uninstall existing Software (Windows only)=== <!--T:1-->+ − ===2. Download Update Software and Install=== <!--T:2-->+ Line 14:
Line 14: − ===3. Driver installation=== <!--T:5-->+ Line 23:
Line 23: − ===4. Validate driver installation (Windows only)=== <!--T:7-->+ Line 35:
Line 35: − ===5. Start BEASTXUpdater=== <!--T:11-->+ Line 72:
Line 72: − ===6. Detect connected BEASTX device=== <!--T:21-->+ Line 92:
Line 92: − ===7. Select Update-File=== <!--T:26-->+ Line 124:
Line 124: − ===8. Perform Update=== <!--T:35-->+
no edit summary
<br />
<br />
<translate>
<translate>
'''1. Uninstall existing Software (Windows only)'''<!--T:1-->
Uninstall any existing BEASTXUpdater/Microsettings installation prior to install the BEASTXSoftware bundle.
Uninstall any existing BEASTXUpdater/Microsettings installation prior to install the BEASTXSoftware bundle.
'''2. Download Update Software and Install'''<!--T:2-->
<!--T:3-->
<!--T:3-->
MacOS 10.6.x and later
MacOS 10.6.x and later
'''3. Driver installation'''<!--T:5-->
Windows:
Windows:
The driver installation will not be launched automatically during setup.
The driver installation will not be launched automatically during setup.
The driver is inside the Disk-Image and must be installed manually.
The driver is inside the Disk-Image and must be installed manually.
'''4. Validate driver installation (Windows only)'''<!--T:7-->
After successful installation of the driver, when the USB2SYS-Interface is connected to the PC, you must be able to find following entry in the Windwos Device Manager:
After successful installation of the driver, when the USB2SYS-Interface is connected to the PC, you must be able to find following entry in the Windwos Device Manager:
To access the device manager under windows 7 type devmgmt.msc in the Startmenu's search bar. Alternatively you can enter the computer properties by pressing and holding the START key on the keyboard and addtionaly pressing the PAUSE key. Then click on device manager in the upper left corner of the appearing window.
To access the device manager under windows 7 type devmgmt.msc in the Startmenu's search bar. Alternatively you can enter the computer properties by pressing and holding the START key on the keyboard and addtionaly pressing the PAUSE key. Then click on device manager in the upper left corner of the appearing window.
'''5. Start BEASTXUpdater'''<!--T:11-->
IMPORTANT: The MICROBEAST will not be powered from the USB2SYS-Interface, so the MICROBEAST must be supplied with power from a different source BEFORE you connect it to the PC, e.g. simply switch on tx and rx as you would go flying (on electric helis take care of the motor!).
IMPORTANT: The MICROBEAST will not be powered from the USB2SYS-Interface, so the MICROBEAST must be supplied with power from a different source BEFORE you connect it to the PC, e.g. simply switch on tx and rx as you would go flying (on electric helis take care of the motor!).
[[File:Step 5_4.jpg|500px]]
[[File:Step 5_4.jpg|500px]]
'''6. Detect connected BEASTX device'''<!--T:21-->
After you selected a COM-Port the BEASTXUpdater will automatically try to identify the unit connected to it.
After you selected a COM-Port the BEASTXUpdater will automatically try to identify the unit connected to it.
Serial-Number is a unique identifier for each MICROBEAST.
Serial-Number is a unique identifier for each MICROBEAST.
'''7. Select Update-File'''<!--T:26-->
If the MICROBEAST was successfully identified you can go on with selecting an Update-File (if you don't have a firmware update file yet, have a look [[Update_request|here]]).
If the MICROBEAST was successfully identified you can go on with selecting an Update-File (if you don't have a firmware update file yet, have a look [[Update_request|here]]).
IMPORTANT: If the major version of the "Data Version" is different between the actual and new firmware, then the Basic-Setup has to be done again after the update.
IMPORTANT: If the major version of the "Data Version" is different between the actual and new firmware, then the Basic-Setup has to be done again after the update.
'''8. Perform Update'''<!--T:35-->
If a valid COM-Port is selected an a valid Update-File was loaded, the "Start Update…" button will be enabled:
If a valid COM-Port is selected an a valid Update-File was loaded, the "Start Update…" button will be enabled: