Difference between revisions of "Translations:Manuals:BXFbl:Radio Setup:RemoteSat/24/en"

From BEASTX Wiki
Jump to navigation Jump to search
(Importing a new version from external source)
 
(Importing a new version from external source)
Line 1: Line 1:
 
'''MICROBEAST PLUS / NANOBEAST'''<br />
 
'''MICROBEAST PLUS / NANOBEAST'''<br />
 
* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.
 
* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.
−
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''H''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
+
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
−
* After successful binding procedure the receiver‘s LED will stay solid. On the MICROBEAST PLUS LED '''H''' will flash alternating with all other LEDs for 2 seconds, then the device will restart. Remove the bind plug. If needed cycle power and enter RECEIVER MENU as further setup steps may be required to use this type of receiver (see above).
+
* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
 
<br />
 
<br />

Revision as of 19:25, 20 May 2024

Information about message (contribute)
This message has no documentation. If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (Manuals:BXFbl:Radio Setup:RemoteSat)
'''MICROBEAST PLUS / NANOBEAST'''<br />
* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
<br />
<br />
Translation'''MICROBEAST PLUS / NANOBEAST'''<br />
* Insert a Spektrum® ''Bind Plug'' at the '''[SYS]''' port.
* To bind a DSMX satellite switch on the power supply now. The yellow LED '''A''' on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
* After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.
<br />

MICROBEAST PLUS / NANOBEAST

  • Insert a Spektrum® Bind Plug at the [SYS] port.
  • To bind a DSMX satellite switch on the power supply now. The yellow LED A on the MICROBEAST PLUS will start to flash immediately. The receiver's yellow LED will start to flash as well. Now you can bind the transmitter as usual (for more information refer to the instructions of your radio control system).
  • After successful binding procedure the receiver‘s LED will stay solid. Then the device will restart and enter RECEIVER MENU if the current receiver type is not set to DSMX or will start with init sequence. Remove the bind plug and proceed.


Retrieved from "https://wiki.beastx.com/index.php?title=Translations:Manuals:BXFbl:Radio_Setup:RemoteSat/24/en&oldid=23554"